• Journal of Advanced Marine Engineering and Technology
• /
• 제23권1호
• /
• pp.79-87
• /
• 1999

The most part of the faculty drop a trouble and damage of machine equipment even if whatever cause they break out take place at local and trifling place and the factor dominating their trouble is due to wear debris occurred in the lubricated machine moving surface. This study has been car-ried out to identify morphology of wear debris on the lubricated machine moving system by means of computer image analysis. Namely the wear debris contained in lubricating oil extracted from movable machine equipment will be filtered through membrane filter(void diameter 0.45${\mu}m$) and will be analyzed with its data information such as 50% volume diameter aspect roundness and reflectivity. Morphological characteristic of wear debris is easily distinguished by four shape parameters it is necessary to divide small class of every 100 wear debris in total wear particles in order to distinguish morphological characteristic of wear debris more easily by computer image analysis. We are sure that operation condition diagnosis of the lubricated machine moving surfaces is possible by computer image analysis.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.152-160
• /
• 1997

A diesel engine oil which was formulated and a commercial diesel engine oil (API CG4) made from same base oil were tested by car and analyzed of their physical, chemical and mechanical properties. The tested oil to be analyzed were sampled from engine every 1000 km until 8000 km and determined the kinematic viscosity, TAN, TBN, metal content in oil, additive depletion, antiwear property and IR analysis. From the study, both the tested oils were almost same properties for the change of TAN and TBN, but the change of kinematic viscosity of formulated oil was slightly higher than that of commercial oil. But the concentration of metal in the formulated oil, especially iron, were increased much less during test. The iron content of the commercial oil was increase rapidly from 7000 km while the formulated oil was still low. These results were conformed by the antiwear test by 4-ball wear test machine for the samples. Also for the commercial oil, the depletion factor of the Zn-DTP which was added as an antiwear property was not change any more after 7000 km. But the formulated oil was change continuously until 8000 km, which mean that the ability of wear protection of the sliding parts exists for the formulated oil. With the results which were analyzed of the properties of oils by field test, it was found that the commercial oil could be used only within 7000 km, but the formulated oil can use more than 8000 km without severe wear of the sliding parts in the diesel engine.

• Journal of Biosystems Engineering
• /
• 제25권6호
• /
• pp.481-488
• /
• 2000

This study was initiated in order to find alternative fuel substituting for light oil the most common fuel for heating greenhouse. The tire oil used in this research was produced by pyrolysis process, one of the final products besides steel string and carbon black in which waste tires as a form of chopped pieces broken by shredding machine are heated up to 200~30$0^{\circ}C$ with maximum restraining of oxygen supply. In order to justify light oil equivalent qualities in tire oil combustion characteristics were defined in the way of comparing kinetic viscosities in the wide range of temperature flame sizes and exhaust gas components in the various combustion conditions. We found that kinetic viscosity of tire oil was lower than light oil by 1 to 2 cSt in the temperature range showing better flowing mobility in the fuel line of the burner and no significant difference in flame size between the two oils in the all combustion treatments. However much more NO and SO$_2$ were detected from the exhaust gases of tire oil than light oil combustions. In fact tire oil contains more nitrogen and total sulfur, by 25 times and 40 times respectively than light oil according to the composition analysis. Tolerable limit for SO$_2$discharge amount defined by the national air pollution standards is under 540ppm so tire oil combustion satisfies the requirement though. It is desirable if sulfur and nitrogen filtering process shall be added in the tire oil production line. Except the exhaust gas components all greenhouse heating qualities of tire oil including hot air temperature are very identical to those of light oil.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.416-423
• /
• 2004

This paper presents the thermal characteristic analysis of a high-speed horizontal machining center with spindle speed of 50,000rpm and feedrate of 120m/fin. The spindle system is designed based on the built-in motor, angular contact ceramic ball bearings, oil-air lubrication and oil-jacket cooling method. The X-axis and Y-axis feeding systems are composed of the linear motors and linear motion guides, and the Z-axis feeding system is composed of the servo-motor, ball screw and linear motion guides. The thermal characteristics such as the temperature distribution, temperature rise, thermal deformation and step response, are estimated based on the finite element model of machining center and the heat generation rates of heat sources related to the machine operation conditions. Especially, the thermal time constant assessed from the step response function is introduced as an index of thermal response characteristics.

• Tribology and Lubricants
• /
• 제24권4호
• /
• pp.179-185
• /
• 2008

Microporous polymer lubricants(MPLs) are solid polymer materials containing micropores which are filled with liquid lubricants, and which are molded or formed to suit rolling bearings or other machine parts requiring lubrication. MPLs can be effectively applied to provide long-term, maintenance-free lubrication of a variety of machine elements without fully replacing of oils and greases. The application of rolling bearings packed fully with an MPL could reduce or eliminate the problems such as grease deterioration, leakage, under-lubrication caused by insertion of water or foreign matters under severe operation conditions. This paper discuss the application of MPLs for lubrication of rolling ball bearings. Two different MPLs were synthesized and the features of MPLs were tested. Characteristics of the bearings which are packed fully with synthesized MPLs were investigated using SEM, TG/DSC, extents of oil leakage, OIT, and life time test. After these preliminary tests twelve MPLs were synthesized and evaluated by measuring extents of oil leakage and OIT values. Then synthesis conditions for the optimum MPL were selected by SSRED(Six Sigma Robust Engineering Design) pro gram using extents of oil leakage and OIT values respectively. The optimum MPL by means of OIT value showed higher performance such as long life time and application at higher temperature of $140^{\circ}C$ than previous temperature of $100^{\circ}C$.

• 농업과학연구
• /
• 제42권4호
• /
• pp.439-446
• /
• 2015

Kimbugak is one of Korea's traditional snacks made of laver. This study was conducted to investigate the physical drying and frying characteristics of kimbugaks made by a pasting & garnishing machine. The drying and frying characteristics should be analyzed to develop a continuous operation system for manufacturing kimbugak because kimbugak has a high moisture content after pasting process. Materials for pasting and garnishing on laver were rice gruel and sesame. The aluminum shelf with square hole was selected as a drying shelf. The recommended size of the square hole type was $1.5mm{\times}1.5mm$ because characteristics of deformation and easy separation from the shelf were excellent at the hole size. The drying time of 2 hours was also recommended with the drying temperature of $70^{\circ}C$ based on the test results such as dried condition (good), moisture conten t (3.7%), deformation (12.1 mm), and shrinkage rate (19.8%). As the frying conditions for dried kimbugaks, recommended oil temperature and frying time were $170^{\circ}C$, 15 seconds, respectively when corn oil was used. In the case of frying for undried kimbugaks, recommended oil temperature and frying time were $210^{\circ}C$, 2 - 3 minutes, respectively for improvement of work efficiency.

• 한국공작기계학회논문집
• /
• 제13권5호
• /
• pp.30-37
• /
• 2004

This paper presents the thermal characteristic analysis of a high-speed horizontal machining center with spindle speed of 50,000rpm and feedrate of 120m／min. The spindle system is designed based on the built-in motor, angular contact ceramic ball bearings, oil-air lubrication and oil-jacket cooling method. The X-axis and Y-axis feeding systems are composed of the linear motors and linear motion guides, and the Z-axis feeding system is composed of the servo-motor, ball screw and linear motion guides. The thermal characteristics such as the temperature distribution, temperature rise, thermal deformation and step response, are estimated based on the finite element model of machining center and the heat generation rates of heat sources related to the machine operation conditions. Especially, the thermal time constant assessed from the step response function is introduced as an index of thermal response characteristics.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.199-203
• /
• 2011

With the improvement of standard of manufacturing process, oil cooling unit for manufacturing machine has been developed. A control system must be designed in order to keep oil temperature of the machine within a very restricted range and also to reduce energy consumption. In order to get the low deviation of the controlled temperature and the low efficiency, the on/off control scheme is gradually being replaced by a variable speed refrigeration system (VSRS) with an inverter driven compressor over recent decades. This paper gives the flowchart to control the compressor speed and also the electronic expansion valve (EEV) aperture in oil cooling unit refrigeration system using R22 as the refrigerant. This control scheme has already tested in experiment apparatus with room temperature condition constant at $25^{\circ}C$ and variable load condition at 4kW, 6kW, 7kW, 8kW and 10kW.

• Tribology and Lubricants
• /
• 제13권1호
• /
• pp.8-13
• /
• 1997

Generally, A motor integrated spindle is selected to perform the high speed machining, to improve the machining flexibility, and to simplify the structure of machine tools. The thermal deformation caused by heat generation of the integrated motor is, however, serious problem in motor integrated spindle system. In this study, cooling characteristics for the several kinds of cooling systems(such as, oil-jacket cooling, air cooling) are investigated and more efficient cooling method is presented. The results show that the shaft cooling by the air cooling system is effective to improve the thermal characteristic of motor integrated spindle.

• 한국정밀공학회지
• /
• 제13권7호
• /
• pp.140-147
• /
• 1996

Machining accuracy of machine tools spindles using the hydrostatic bearing, largely depends on the static stiffness and the thermal deformation of the spindle unit. In this paper, the modelling and static, thermal analysis of the hydrostatic spindles were performed for the relationship between the design variables like the bearing span, overhang, bearing stiffness and static stiffness at spindle. The goal of optimization is the mazimum, static stiffness at spindle nose with lower temperature rise in hydrostatic bearing. Temperature rise of hydrostatic bearing is minimized with the variables of spindle diameter and oil supply pressure. Finally, validity of the proposed algorithm is verified by improving the static, thermal performance of the existing hydrostatic spindles.