• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.221-223
• /
• 2000

This paper describes the design of SVC fuzzy logic controller (SVC-FLC) using adaptive evolutionary algorithm and we tuned the gain of input-output variables of SYC-FLC using it. We performed the nonlinear simulation on an single-machine infinite system to prove the efficiency of the proposed method. The proposed SYC-FLC showed the better performance than PD controller in terms of the settling time and damping effect, for system operation condition used in evaluating the robustness and three phase grounding default in cases of nominal loading used in tuning SVC-FLC for a single-machine infinite system.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.3
• /
• pp.57-64
• /
• 2016

This paper deals with the PCB assembly time minimization problem that the PAP (pick-and-placement) machine pickup the K-weighted group of N-components, loading, and place into the PCB placement location. This problem considers the rotational turret velocity according to component weight group and moving velocity of distance in two component placement locations in PCB. This paper suggest heavy-weight component group first pick-and-place strategy that the feeder sequence fit to the placement location Hamiltonean cycle sequence. This algorithm applies the quadratic assignment problem (QAP) that considers feeder sequence and location sequence, and the linear assignment problem (LAP) that considers only feeder sequence. The proposed algorithm shorten the assembly time than iATMA for QAP, and same result as iATMA that shorten the assembly time than ATMA.

• The Journal of the Korean dental association
• /
• v.11 no.1
• /
• pp.41-44
• /
• 1973

The experiment consisted of cementing full veneer crown of extracted teeth and a standardized cylindrical metal dies (6mm diameter, 6mm height, 1mm shoulder) and then measuring the tensile strength required to remove the cemented restoratoins by the Instron testing machine in the Korea Institude of Science and Technology. The Instron machine was operated at a rate of loading of 0.2cm per minute. From the experiments, the following results obtained. 1. The tension of zinc phosphate and alumina EBA cements were highest all of the cements. 2. The tension of Fynal and the addition of eugenol to zinc Phosphate cements were similar. The addition of eugenol to zinc phosphate cement was half stength and Fynal cement was on third strength than zinc phosphate cement. 3. The tension of zinc oxide-eugenol cement was lowest all of the cements.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.651-657
• /
• 1996

Industrial products are getting more and more complex. The number of parts or components and the variety of manufacturing processes are increasing. This leads to rapid product oriented machine tools. The process integrated CNC lathe is one of the these machine tools which can produce numerous parts and various machining processes and reduce the lead time and non-machining time. Therefore this study deals with the design technique of a process-intergated CNC lathe which can reduce the tact time and production cost by the speed-up of the tooling system and the high-speed machining oriented construction of 2 spindles and 2 turrets.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.10a
• /
• pp.33-37
• /
• 2000

Milling fixture is one kind of machining device according to the industrial demands for multi manufacturing products on the growing at alarming rate. In the field of design and making for machine tool working, welding, assembling with fixture for mass production is a specific division. In order to prevent the production defects, occurring, the optimum design of product, fixture putting in the field is very significant manufacturing method. They require analysis of many kinds of important factors, theory and practice of machine tool operating process and its situations, fixture and its structure, machining condition for tool making tool materials, heat treatment of fixture components, know-how and so on. In this study we designed and constructed a milling fixture of mass production and performed tryout under the AUTO CAD, database, I-DEAS and WINDOW environment. Especially part 1 of this study is reveals with the analysis of part drawing, fixture planning, fixture design etc.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.441-446
• /
• 2000

Although the net-shape molding of composites is generally recommended, molded composites frequently required cutting or grinding due to the dimensional inaccuracy for precision machine elements. During the composite machining operations such as cutting and grinding, the temperature at the grinding area may increase beyond the allowed limit due to the low thermal conductivity of composites, which might degrade the matrix of composite. Therefore, in this work, the temperature at the grinding point during surface grinding of carbon fiber epoxy composite was measured. The grinding temperature and surface roughness were also measured to investigate the surface grinding characteristics of the composited. The experiments were performed both under dry and wet grinding conditions with respect to cutting speed, feed speed, depth of cut and stacking angle. From the experimental investigation, the optimal conditions for the composite plain grinding were suggested.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.6
• /
• pp.98-104
• /
• 1999

As the accuracy of manufactured goods needed high accuracy processing has made the efficiency of NC and measurement technology development, the innovation of machine tools has influence the development of the semi-conductor and optical technology. The movement errors can be expressed in terms of yaw, roll an pitch etc. In the case of expanding the error range, static, dynamic and servo gain errors can be included. Machining center might have twenty-one movement errs including three types of joint errors. Those errors have been measured on the condition of just loading of standard table. Regarding these measuring methods, the mechanical compliance of the structure has not been considered. In this paper, therefor, the influences of the additional load on the positioning accuracy are investigated. The results and the techniques proposed in this study can be considered very effective and useful to compensate more correctly the positioning motion.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.229-234
• /
• 1999

This thesis presents the design method using CAE(Computer Aided Engineering) with the consideration of reliability for optimal gear driving system. The validity and feasibility of the proposed method are verified by the application to transmission of machine tool. The reliability and life analysis is based on the two-parameter Weibull distribution lives of the gears and bearings. Ninety-percent of reliability life is the life of the component or system in million output rotations or hours at which ninety percent of identical components or system would survive under the given loading conditions.

• Transactions of Materials Processing
• /
• v.3 no.3
• /
• pp.359-374
• /
• 1994

Process sequence design in sheet metal forming process by the finite element method is investigated. The forming of sheet metal into a washing machine container is used to demonstrate the design of an improved process sequence which has fewer operations. The design procedure makes extensive use of the finite element method which has simulation capabilities of elastic-plastic modeling. A one-stage process to make an initial blank to the final product is simulated to obtain information on metal flow requirements. Loading simulation for a conventional method is also performed to evaluate the design criteria which are uniform thickness distribution around the finished part and maximum punch load within limit of available press capacity. The newly designed sequence has two forming operations and can achieve net-shape manufacturing, while the conventional process sequence has three forming operations. This specific case conventional process sequence has three forming operations. This specific case can be considered for application of the method and for development of the sequence design methodology in general.

• Steel and Composite Structures
• /
• v.31 no.5
• /
• pp.427-435
• /
• 2019

The estimation of moment and rotation in steel rack connections could be significantly helpful parameters for designers and constructors in the initial designing and construction phases. Accordingly, Extreme Learning Machine (ELM) has been optimized to estimate the moment and rotation in steel rack connection based on variable input characteristics as beam depth, column thickness, connector depth, moment and loading. The prediction and estimating of ELM has been juxtaposed with genetic programming (GP) and artificial neural networks (ANNs) methods. Test outcomes have indicated a surpass in accuracy predicting and the capability of generalization in ELM approach than GP or ANN. Therefore, the application of ELM has been basically promised as an alternative way to estimate the moment and rotation of steel rack connection. Further particulars are presented in details in results and discussion.