• 대한기계학회논문집B
• /
• 제21권9호
• /
• pp.1198-1206
• /
• 1997

The flow characteristics of an intermittent fuel injection into a stationary ambient air were investigated using gasoline. The measurements were made by two-channel, air cooling type Phase Doppler Anemometer(PDA) system (DANTEC, 750 MW). And a pintle type injector of MPI (Multi-point Port Injection) system was utilized as a fuel injector. The PDA receiver optic was set up in a 60.deg. C forward scatter arrangement to obtain the optimum scattering signal of fuel droplets. The data were obtained by synchronizing PDA system with the fuel injection period, and the axial and radial velocity and turbulent components of fuel droplets were mainly measured for the analysis of temporal and spatial distribution depending upon the fuel injection pressures.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.97-103
• /
• 1997

Effects of fuel injection timing on the lean misfire limit of a sequential MPI SI engine has been investigated. To investigate the interaction of injection timing and intake flow characteristics, so called axial stratification phenomena, 4 kinds of different intake swirl port of the same combustion chamber geometry have been teated in a single cylinder engine test bench. And 2 kinds of fuel, gasoline and compressed natural gas(CNG), were used to see the effect of liquid fuel vaporization. Result shows that combination of port swirl and injection timing governs the lean misfire limit and lean misfire limit envelopes remain almost the same for a given ratio regardless of engine speed. It is also found that two phase flow has some effects on lean misfire limit.

• 한국분무공학회지
• /
• 제16권3호
• /
• pp.146-151
• /
• 2011

LPG(Liquified Petroleum Gas) fuel for vehicles has lots of advantages such as low emission level, cheaper fuel cost and enough infrastructure. Therefore it arouses interest as an alternative engine to reduce emission of diesel engines. Especially MPI(Multi Point Injection) type LPLi(Liquid Phase LPG injection) system could have overcome the disadvantages of mixer types such as low engine performance, decreased charging efficiency and cold starting difficulty. However ice formation on the nozzle tip and intake port due to the freezing of moisture around the components is often observed in LPLi systems. This icing phenomenon is the direct cause of unstable engine combustion, resulting in engine emissions. Therefore in this research, a spray visualization test for LPG injection was carried out to obtain the basic information of an LPLi injector, then the effects of butane and propane mixing rates on ice formation at the intake port and nozzle tip was investigated. As a result, the icing characteristics of them showed contrary results according to the mixing rates.

• 한국자동차공학회논문집
• /
• 제14권6호
• /
• pp.73-81
• /
• 2006

A commercial diesel engine was converted into a dedicated natural gas engine to reduce the exhaust emissions in a retrofit of a diesel-fueled vehicle. The cylinder head and piston were remodeled into engine parts suited for a spark ignition engine using natural gas. The remodeling of the combustion chamber changed the compression ratio from 21.5 to 10.5. A multi-point port injection(MPI) system for a dedicated natural gas engine was also adopted to increase the engine power and torque through improved volumetric efficiency, to allow a rapid engine response to changes in throttle position, and to control the precise equivalence ratio during cold-start and engine warm-up. The performance and exhaust emissions of the retrofitted natural gas engine after remodeling a diesel engine are investigated. The emissions of the retrofitted natural gas engine were low enough to satisfy the limits for a transitional low emission vehicle(TLEV) in Korea. We concluded that a diesel engine can be effectively converted into a dedicated natural gas engine without any deterioration in engine performance or exhaust emissions.

• 한국가스학회지
• /
• 제23권6호
• /
• pp.90-96
• /
• 2019

셰일가스의 채굴량 확장과 러시아를 통한 PNG (Pipeline Natural Gas)의 도입은 천연가스가 유력한 대체 연료임을 시사해주고 있다. 따라서 향후 증대될 천연가스의 공급에 맞추어 해당 연료의 수요처 증대가 필수적인 상황이다. 이와 같은 상황에서 수송분야는 저탄소 기체 연료인 천연가스를 적용하기 적합한 분야이며, 이를 통해 이산화탄소와 입자상 물질 등의 유해 배기물질을 저감하는 데 큰 역할을 할 것으로 기대된다. 천연가스는 자발화 특성이 낮고, 내노킹(Anti-knocking)성이 우수하기 때문에 전기점화 방식에 적합하다. 최근 가솔린 엔진은 연비 개선을 위해 연소실에 직접 분사하는 방식을 주로 채택하고 있으나,연소실 내로 액상 직분사를 하는 반면 천연가스의 경우 액상분사 혹은 고압 분사가 어렵다. 따라서 포트에 분사하는 방식을 사용하므로 동등 흡기압력에서 연료의 분율이 흡입공기의 체적을 대체하여 가솔린 직분 방식에 비해 출력이 저하되는 현상을 피할 수 없게 된다. 이에 본 연구에서는 터보차저를 천연가스 포트 분사 엔진에 적용하여 흡기 압력 상향을 통한 출력 보상을 도모하고자 하였다.그 결과 천연가스 적용 시 흡기압력을 기존 가솔린 대비 5-27 % 상향 시 가솔린 직분사 엔진과 동등 출력을 확보함과 동시에 향상된 제동 열효율을 확인 할 수 있었다.