• Journal of the Korean Graphic Arts Communication Society
• /
• v.30 no.1
• /
• pp.1-19
• /
• 2012

According as gradually increasing the demand for eco-friendly at the printing process, it has been progressed fairly development. Especially, the inks are used by soy oil beginning of ink industry for preventing environment, it is possible to make eco-friendly inks with vegetable ester. So it is not necessary to use petroleum-based solvents at all for preventing environment. These eco-friendly inks have a benefits they are able to use the renewable resource. But basically vegetable oils have that reduce the VOC(Volatile Organic Compound) and high viscosity, high solubility properties. So if the vegetable oils use in the ink, set off problem occur on the paper because of slow drying time. In case of vegetable ester, it has similar the molecular weight and kinetic viscosity with hydrocarbon solvent, it is able to control the power of dilution about the resin. So, it has benefit that solve the problem of the existing eco-friendly inks. In this study, different types of ester were made by six types of vegetable oils and used ester in the varnishes and inks properties are comparison with hydrocarbon solvent based ink. By considering the intrinsic properties of vegetable oil, ester used to analyze the changes in ink properties, using ester varnish is applied to study the rheology characteristics and emulsification with inks.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.4
• /
• pp.302-311
• /
• 2016

This paper proposes a hybrid ESS that integrates an energy storage system (ESS) with an uninterruptible power supply (UPS). The hybrid ESS has a demand management and emergency power supply function while increasing the battery utilization of the UPS, which has just been used in a power failure. In addition to the critical load, the proposed system augments the capacity of emergency generation using an additional load, which has voltage and frequency-dependent characteristics to the grid side. The control algorithm of the AC-DC converter and bidirectional DC-DC converter is proposed for demand management and emergency power supply. Furthermore, seamless and autonomous transfer methods to alleviate the transient during mode transfer are proposed. To validate the proposed control scheme, experimental results from a 5 kW prototype are provided.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.339-344
• /
• 1993

An H$_{\infty}$ control system design for a magnetic levitation system is presented. In the control system design, we consider the influence of both disturbances and uncertainties in the model. The main disturbances stem from the position sensors.The uncertainties are divided into electromagnetic and mechanical ones: the former are due to the gain change in the current amplifier, the influence of leakage flux and modelling error in the magnetic circuit and the latter are due to the changes of the mass and the moments of inertia of the vehicle. Therefore, the designed controller is indispensable to guarantee the robustness of this system for both stability and performance. The controller design is based on the standard H$_{\infty}$ optimal control problem. As the novel features in this paper :(1) there are two poles on j.omega.-axis in the control model;(2) an integrator is included in the controller so that equivalently there are three poles on j.omega.-axis in the model. Finally, several experiments and simulations are carried out to verify the high performance and robustness of the designed control system.m.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.1
• /
• pp.26-34
• /
• 2010

Effects of drying condition (IR radiation) on the optical properties and the printability of coated paper were elucidated at various latex sizes and low and high coating color concentrations. It was found that the smaller latex provided better rheology and higher dry and wet pick strength than the larger one. The high solids coating resulted in higher paper gloss and smaller roughness than the low solids coating, even though the clay addition was reduced by 20 parts in the high solids coating. Increasing IR radiation prohibited binder migration into the base paper. Thus it improved binder distribution and decreased pores in the coated layer, resulting in the increased dry and wet pick strength and the improved printing gloss. On the other hand, the color trapping and ink set-off was impaired with increasing IR radiation. Print mottle index passed through a maximum with increasing IR radiation.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.21 no.2
• /
• pp.75-87
• /
• 2003

Printing inks are mainly composed of pigment and vehicles. Among these components, the Vehicle affect the rheologic property of the ink the most but pigment content of characteristic also after to the fluidity property not less than the vehicle. In the study, It is tested effect to the ink fluidity and structure recovery according to change the pigment particle size. The ink fluidity have been observed by using rheometer at the various conditions and it has been tested to observe what the ink fluidity has different means. In result We have found that the viscosity value of the low shear rate range has relatively higher value with decreasing the pigment particle size in the ink. Also, it has been found that when the pigment particle size decreases, the yield stress gradually increase. In the case of ink's structure recovery, when the pigment particle size decreases in the ink, the less changing shear rate, and it takes less time to recover.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.45 no.2
• /
• pp.114-121
• /
• 2009

There are increased in using the bio-ethanol, as the carbon neutral attracts many researchers due to a reduction in carbon dioxide spotted as the global warming gas. A gasoline engine with 100% of the bioethanol was developed and used in Brazil already, but researches of using the bio-ethanol in diesel engines are lack. In this study, combustion tests with blend fuel of the gas oil and bio ethanol by 50% maximally due to a low cetane number of bio-ethanol were accomplished as a basic study of introduction of using the bioethanol in diesel engines. The result was that smoke emission was decreased with increase in proportion of the bio-ethanol, due to the increase of a amount of pre-mixed combustion with ignition delay. Although the amount of $CO_2$ is reduced according as the bio-ethanol is used(carbon neutral), the emission of $CO_2$ with increase in the proportion of the bio-ethanol was more increased due to lower a heat value of bio-ethanol than gas oil.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.301-306
• /
• 2002

This paper presents the use of the neural network technology to establish a mathematical model for predicting bead geometry (top-bead width, top-bead height, back-bead width and back-bead height) for multi-pass welding, and understand relationships between process parameters and bead geometry for robotic GMA welding process. Using a series of robotic arc welding, additional multi-pass butt welds were carried out in order to verify the performance of the developed neural network model. The results show that not only the proposed model can predict the bead geometry with reasonable accuracy and guarantee the uniform weld quality, but also the neural network model could be better than the linear and curvilin ear equations developed from Lee [8].

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.722-727
• /
• 1996

A simple compost windrow-forming car and a compost tuner were developed at the aim of low cost manure management systems. The developed compost windrow- forming car is possible windrows formation at a short time. In order to be pulverized and mixed by upper and lower beaters at the windrow-forming, the condition of air and the mixing of materials to play a major role in composting is filled. This car can also utilized for a manure spreader by folding the windrow-forming cover. The developed compost turner is a type equipped with tractor rear-right side. Main specifications are 2.5m working width, overall length 3.3m and 45degrees conveyer inclination angle, 2 beaters for mixing and pulverization are equipped in front parts. Windrows of 2.5m width and 1.5m height are turned at the speed of 4.5-5.1m/min. In accordance with the above, by combining the compost windrow-forming car and the compost turner, a simple composting system for each farmer could be constructed by the low c st.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.5
• /
• pp.36-41
• /
• 2008

Multi-ply sheet forming has many advantages including the possibility of using wide range of materials in a given structure, lowering production cost, making higher grammage products and so on. But, incorrect structure of sheet makes flow resistance higher so that it shows poor dewatering in press section. One of major factors that affect sheet structure and dewatering property is fines content in each layer. We, therefore, examined the press dewatering of multi-ply sheet that has the different fines content in each layer and the effect of fines distribution on physical properties of sheet to find a technology for optimum utilization of raw materials. In case of two layered sheet, the sheet which was composed of layers with the different flow resistance showed higher dewatering rate than one which has the same flow resistance. And the more difference in fines content for layers existed, the more dewatering occurred. For three layered sheets, dewatering is mainly dependent on fines content of bottom layer. Strength properties were affected by dewatering degree and multi-ply sheet structure.

• Elastomers and Composites
• /
• v.22 no.3
• /
• pp.213-218
• /
• 1987

In this study, the rheological properties of a partially valcanized black filled EPDM were investigated as a function of degree of crosslinks using capillary rheometer. In order to obtain the samples having various degree of crosslinks between 0 and 6 percent, the vulcanization kinetics was also studied by Monsanto rheometer. The results showed that the die swell ana the pressure drop at the capillary entrance and exit increase nearly linearly with the increase in degree of crosslinks. However, melt fracture occurred at a lower shear rate for the samples of higher degree of crosslinks. These results were discussed in terms of the melt elasticity produced at the entrance region of capillary by the partial vulcanization. It is also interesting to note that the fluctuation of die swell during the practical extrusion or calendering process in the factories can be caused by the partial vulcanization occurred during the process.