• 대한치과기공학회지
• /
• 제26권1호
• /
• pp.35-40
• /
• 2004

In order to understand alloying effects on the corrosion resistance of Ti-(10$\sim$20)%Zr-(2$\sim$8%)Nb-0.2%Pd alloys, Polarization curves were measured at 5%HCI solution. The results were interpreted in terms of two parameters obtained by the molecular orbital calculation ; one is the bond order($B_{\circ}$) and the other is the metal d-orbital level($M_{d}$). $B_{\circ}$ is a measure of the strength of covalent bonds between titanium and alloying elements. $M_{d}$ is correlative with the electronegativity of elements. It was found that increasing of Zr and Nb with higher $B_{\circ}$ values showed a lower critical anodic current density in the polarization curve and hence higher corrosion resistance. On the other hand, increasing of Zr and Nb with higher $M_{d}$ values showed a higher corrosion resistance.

• Journal of Electrochemical Science and Technology
• /
• 제10권2호
• /
• pp.148-158
• /
• 2019

The corrosion protection of AA2024 PPy coated samples doping with nanosized metal oxides, including $TiO_2$ and $CeO_2$ nanoparticles and $Nd_2O_3$ nanorods, during exposure to the solutions of 0.1 M $H_2SO_4$ and 3.5% NaCl was evaluated by electrochemical impedance spectroscopy (EIS) and linear polarization resistance (LPR) techniques. The nanorods of $Nd_2O_3$ were synthesized by cathodic pulse electrochemical deposition technique. The barrier properties of the different PPy coatings containing nanosized metal oxides immersed in $H_2SO_4$ solution were ranked as follows: $Nd_2O_3$ > $TiO_2$ > $CeO_2$. Therefore, the $Nd_2O_3$ coating sample provided the highest corrosion protection at any time of immersion up to 72 hours after immersing in $H_2SO_4$ solution. On the other hand, the $CeO_2$ coating sample displayed the best anticorrosive properties among the other coating samples after immersion in NaCl solution up to 28 days. This is due to the inhibition effect of cerium ions on aluminum alloys at near-neutral solutions.

• 천문학회보
• /
• 제46권1호
• /
• pp.45.2-46
• /
• 2021

The Hayabusa 2 mission target asteroid (162173) Ryugu is a near-Earth, carbonaceous (C-type) asteroid. Before the arrival, this asteroid is expected to be covered with mm- to cm- sized grains through the thermal infrared observations [1]. These grains are widely understood to be formed by past impacts with other celestial bodies and fractures induced by thermal fatigue [2]. However, the close-up images by the MASCOT lander showed lumpy boulders but no abundant fine grains [3]. Morota et al. suggested that there would be submillimeter particles on the top of these boulders but not resolved by Hayabusa 2's onboard instruments [4]. Hence, we conducted polarimetry of Ryugu to investigate microscopic grain sizes on its surface. Polarimetry is a powerful tool to estimate physical properties such as albedo and grain size. Especially, it is known that the maximum polarization degree (Pmax) and the geometric albedo (pV) show an empirical relationship depending on surface grain sizes [5]. We observed Ryugu from UT 2020 November 30 to December 10 at large phase angles (ranging from 78.5 to 89.7 degrees) to derive Pmax. We modified TRIPOL (Triple Range Imager and POLarimeter, [6]) to attach to the 1.8-m telescope at the Bohyunsan Optical Astronomy Observatory (BOAO). With this instrument, we observed the asteroid and determined linear polarization degrees at the Rc-band filter. We obtained sufficient data sets from 7 nights at this observatory to determine the Pmax value, and collaborated with other observatories in Japan (i.e., Hokkaido University, Higashi-Hiroshima, and Nishi-Harima) to acquire linear polarization degrees of the asteroid from total 24 nights observations with large phase angle coverage (From 28 to 104 degrees). The observational results have been published in Kuroda et al. (2021) [7]. We thus found the dominance of submillimeter particles on the surface of Ryugu from the comparison with other meteorite samples from the campaign observation. In this presentation, we report our activity to modify the TRIPOL for the 1.8-m telescope and the polarimetric performance. We also examine the rotational variability of the polarization degree using the TRIPOL data.

• 멤브레인
• /
• 제2권1호
• /
• pp.59-66
• /
• 1992

십자류 흐름 평판형 cell에서 비대칭 cellulose acetate 막으로 PEG #6000 및 dextran 70T 용액의 한외여과를 압력차와 도입용액 농도 변화에 따라 실험하여 막투과량 및 용질 배제도를 측정하고, 막투과량에 미치는 농도분극층 저항을 고찰하였다. 이 결과 농도분극층 저항 $R_{b1}$을 농도분극층내의 고분자 용액의 평균 농도 $C_{b1}$과 상관시켜 다음의 무차원 관계식으로 나타낼 수 있었다. $\frac{R_{b1}}{{R_m}}=\alpha[\frac{\rho_{b1}}{C_{b1}}]^\beta$

• 한국결정성장학회지
• /
• 제6권4호
• /
• pp.571-583
• /
• 1996

1 mM의 $[Fe(CN)_{6}]^{3-}/[Fe(CN)_{6}]^{4-}$ 이온이 첨가된 0.5 M $K_{2}SO_{4}$용액에서 Impedance spectroscopy를 통하여 비교적 porous한 표면조직을 갖는 흑연재료인 electrographite와 graphite foil의 계면의 전기화학적 거동을 조사하였다. 이들 두 흑연재료의 변전위 전류 전압곡선의 경우 전극표면의 구조로 인하여 비교적 높은 전류가 나타났으며, graphite foil의 경우 높은 이중층 용량이 나타났다. 또한 두 재료 모두 field transport의 작용에 의해 분극증가에 따른 임피던스 스펙트럼의 변화와 Faraday-임피던스의 변화가 크게 나타나지 않았다. 특히 electrographite의 경우 전극계면에서 흡착현상이 나타났으며, 양극분극의 증가에 의해 흡착현상은 현저하게 증가하였다.

• Restorative Dentistry and Endodontics
• /
• 제12권1호
• /
• pp.39-49
• /
• 1986

The purpose of this study was to observe characteristic properties through the polarization curves and SEM images from 4 different types of amalgam obtained by using the potentiostats (Princeton EG & G) & SEM (Jeol/35), and to investigate the degree of corrosion on the oxidation peak of the each phase of amalgam. After each amalgam alloy and Hg was triturated as the direction of the manufacturer by means of the mechanical amalgamator (Shofu Co.), the triturated mass was inserted into the cylindrical metal mold which was 12mm in diameter and 10.0mm in height and was condensed by using routine manner. The specimen was removed from the mold and stored at room temperature for about 24 hours. The standard surface preparation was routinely carried out. Anodic polarization measurement was employed to confirm the corrosion behaviour of the amalgams in a 0.9% saline solution (P.H: 6.8-7.0) at $37^{\circ}C$. The initial rest potential (corrosion potential) was determined after 30 minutes of immersion of specimen in electrolyte, and the potential scan was begun at the point of 100mV cathodic from the corrosion potential. The scan rate was 0.17mV/sec. in the study to observe the degree of corrosion of each phase. SEI and EPMA images on the determined oxidation peaks of each amalgam were observed. The results were as follows: 1. In the four anodic polarization curves, low copper amalgams have three oxidation peaks and high copper amalgams have two oxidation peaks, -270mV, +26mV and +179mV(SEC) in the low copper lathe cut, and -300mV, +39mV and +163mV(SEC) in the low copper spherical. -4mV and +154mV(SEC) in the Dispersalloy, and +17mV and +180mV(SEC) in the Tytin as high copper amalgams. 2. ${\gamma}_2$ phase in the low copper amalgam and ${\eta}$ phase in the high copper amalgam were the most corrodible phases and Ag-Cu eutectic in high copper amalgam was the most slowly corroded phase. 3. Low copper amalgam was more susceptible in corrosion than high copper amalgam.

• 한국광학회지
• /
• 제32권2호
• /
• pp.49-54
• /
• 2021

본 논문에서는 고출력 광섬유 레이저의 핵심 부품인 대구경 광섬유 엔드캡을 제작하는 장비를 설계 및 제작하였으며, 제작장비를 이용하여 대구경 광섬유 엔드캡을 제작하였다. 대구경 광섬유 엔드캡 제작장비는 레이저 광을 조사하여 접속 열원으로 사용하기 위한 CO2 레이저 광원부, 대구경 광섬유와 엔드캡의 위치를 이송하기 위한 정밀 스테이지 조립체, 스테이지 조립체와 연동되어 융착 시 정렬에 사용되는 비전 시스템으로 구성되어 있다. 레이저 광원의 출력은 스테이지 조립체와 연동되어 출력을 제어하며, 비전 시스템으로 대구경 편광유지 광섬유의 편광축을 정렬할 수 있도록 제작되었다. 자체 제작한 장비를 이용하여 클래드 직경이 400 ㎛인 대구경 편광유지 광섬유와 10(W)×5(D)×2(H) ㎣의 엔드캡을 레이저 융착하여 대구경 광섬유 엔드캡을 제작하였다. 제작된 대구경 광섬유 엔드캡의 신호광 삽입손실, 소광률 및 빔품질(M2)은 각각 0.6%, 16.7 dB, M2x=1.21, M2y=1.22로 측정되었다.

• 대한화학회지
• /
• 제41권1호
• /
• pp.1-11
• /
• 1997

0.5 M $K_2SO_4$ 용액에서 여러 가지 세 탄소전극(glassy carbon, 인조흑연, graphite foil)에 대하여 양극분극에 따른 전극표면반응에 대한 연구를 임피던스 스펙트로스코피를 통하여 실시했다. Graphite foil 전극의 경우 이중츨 capacotance는 다른 두 전극재료에 비하여 높게 나타났으며, 양극분극시 glassy carbon과 인조 흑연(PVDF 혼합 graphite)은 전극계면에서 흡착현상에 의한 capacitance C의 영향이 현저하게 나타남을 알 수 있었다. 3종류 전극재료의 전기화학적 거동은 전극표면 조직의 차이에 의해 glassy carbon의 경우는 분극시 파라데이 임피던스의 영향을 받으며, graphite foil의 경우는 field transport의 지배를 받아 전압의 변화에 의한 임피던스 파라미터의 변화는 거의 나타나지 않았다.

• Molecules and Cells
• /
• 제38권10호
• /
• pp.886-894
• /
• 2015

Macrophages are divided into two subpopulations: classically activated macrophages (M1) and alternatively activated macrophages (M2). BCG (Bacilli Calmette-$Gu{\acute{e}}rin$) activates disabled $na{\ddot{i}}ve$ macrophages to M1 macrophages, which act as inflammatory, microbicidal and tumoricidal cells through cell-cell contact and/or the release of soluble factors. Various transcription factors and signaling pathways are involved in the regulation of macrophage activation and polarization. We discovered that BCG-activated macrophages (BAM) expressed a new molecule, and we named it Novel Macrophage Activated Associated Protein 1 (NMAAP1). 1 The current study found that the overexpression of NMAAP1 in macrophages results in M1 polarization with increased expression levels of M1 genes, such as inducible nitric oxide synthase (iNOS), tumor necrosis factor alpha (TNF-${\alpha}$), Interleukin 6 (IL-6), Interleukin 12 (IL-12), Monocyte chemoattractant protein-1 (MCP-1) and Interleukin-1 beta (IL-$1{\beta}$), and decreased expression of some M2 genes, such as Kruppel-like factor 4 (KLF4) and suppressor of cytokine signaling 1 (SOCS1), but not other M2 genes, including arginase-1 (Arg-1), Interleukin (IL-10), transforming growth factor beta (TGF-${\beta}$) and found in inflammatory zone 1 (Fizz1). Moreover, NMAAP1 overexpression in the RAW264.7 cell line increased cytotoxicity against MCA207 tumor cells, which depends on increased inflammatory cytokines rather than cell-cell contact. NMAAP1 also substantially enhanced the phagocytic ability of macrophages, which implies that NMAAP1 promoted macrophage adhesive and clearance activities. Our results indicate that NMAAP1 is an essential molecule that modulates macrophages phenotype and plays an important role in macrophage tumoricidal functions.

• International Journal of Concrete Structures and Materials
• /
• 제18권1E호
• /
• pp.3-9
• /
• 2006

Five slab specimens with predefined cracks are examined to evaluate the corrosion behavior of epoxy-coated bars in chloride contaminated concrete, using linear polarization method. The test specimens were subjected to alternating weekly cycles of ponding in a salt solution and drying for 48 weeks. Test results show that the current density of the specimen of normal steel bars becomes 0.715 ${\mu}A/cm^2$ indicating that the steel bars are in moderate or high corrosion condition. However, the corrosion rates of the specimens with damaged epoxy-coated bars are significantly below 0.1 ${\mu}A/cm^2$ and the bars appears to be in passive condition. The damaged epoxy-coated bars with a corrosion inhibitor of calcium nitrite showed a corrosion rate of 0.110 ${\mu}m/year$ or 56 percents of the corrosion rate of damaged epoxy-coated specimen without such an inhibitor, 0.195 ${\mu}m/year$. However, the corrosion rates of specimens containing the other two corrosion inhibitors, a combination of amines and esters or mixtures of organic alkenyl dicarboxyl acid salts are quite equivalent to the control specimen. The research technique of linear polarization resistance method has proven itself to be useful in measuring corrosion rates of reinforcement in concrete.