• Tribology and Lubricants
• /
• v.38 no.6
• /
• pp.267-273
• /
• 2022

Surface texturing is the latest technology for processing grooves or dimples on the friction surface of a machine. When appropriately applied, it can reduce friction and significantly increase durability. Despite many studies over the past 20 years, most are isothermal (ISO) analyses in which the viscosity of the lubricant is constant. In practice, the viscosity changes significantly owing to the heat generated by the viscous shear of the lubricant and film-temperature boundary condition (FTBC). Although many thermohydrodynamic (THD) analyses have been performed on various sliding bearings, only few results for surface-textured bearings have been reported. This study investigates the effects of the FTBC and groove number on the THD lubrication characteristics of a surface-textured parallel thrust bearing with multiple rectangular grooves. The continuity, Navier-Stokes, and energy equations with temperature-viscosity-density relations are numerically analyzed using a commercial computational fluid dynamics code, FLUENT. The results show the pressure and temperature distributions, variations of load-carrying capacity (LCC), and friction force with four FTBCs. The FTBCs greatly influence the lubrication characteristics of surface-textured parallel thrust bearings. A groove number that maximizes the LCC exists, which depends on the FTBC. ISO analysis overestimates the LCC but underestimates friction reduction. Additional analysis of various temperature boundary conditions is required for practical applications.

• Tribology and Lubricants
• /
• v.16 no.6
• /
• pp.415-424
• /
• 2000

The use of magnetoresistive (MR) head requires much tighter control of particle contamination in a drive since loose particles on the disk surface will generate thermal asperities (TA). In this study, a spinoff test was performed to investigate the adhesion and removal capability of a particle to disk surface. Numerical simulation was also performed to investigate dominant factor of particle detachment and to support experimental results. It was shown that particles are detached from the disk surface by the moment derived from the centrifugal force and the drag force and that the centrifugal force and capillary force are the dominant force, which determines spin-off of a particle on the disk surface. Removal of particles smaller than several micrometers, which are the main source of TA generation, is extremely difficult since the adhesion forces exceed the centrifugal force. Lubricant types and manufacturing process also influence the particle removal. Lower bonding ratio and lower viscosity of the lubricant will help to increase the removal rate of the particles from the disk surface.

• Transactions of Materials Processing
• /
• v.14 no.8 s.80
• /
• pp.668-674
• /
• 2005

In sheet metal forming, drawbeads are often used to control uneven material flow which may cause deffets such as wrinkles, fractures, surface distortion and springback. Appropriate setting and adjusting of the drawbead force is one of the most important parameters in sheet forming process control. Therefore in this study, drawbead friction test with circular shape bead was performed at various sheets, lubricants(dry, three kinds of lubricants having different viscosities), bead materials and surface treatments of bead surface. The results obtained by drawbead friction test show that the friction and drawing characteristics of deforming panels were mainly influenced by strength of sheet, viscosity of lubricant and hardness of bead surface.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.269-274
• /
• 2004

It is important to decide the minimum film thickness and viscosity variations of a multigrade lubricant in the contact surface under the high pressure conditions. By carrying out acceleration, deceleration, and various sliding-rolling ratio movement between two contact bodies, it is experimented that film formation variations in the contact surface are captured with multigrade lubricants in order to exactly investigate the variations of film formations. Optical interference images are continuously captured with high resolution CCD camera during the captured period of acceleration, deceleration. The friction forces between the contacting bodies are also measured simultaneously with the film formation.

• Tribology and Lubricants
• /
• v.19 no.2
• /
• pp.85-93
• /
• 2003

In this study, a multigrid multi-integration method has been used to solve the steady-state, elastohydrodynamic lubrication (EHL) point contact problem of a ball joint mechanism used in small reciprocating compressors. Pressure and film thickness profiles have been calculated at minimum and maximum Moes M parameter conditions during one revolution of crankshaft. The effects of various lubricant viscosities, loads, ball velocities, elastic modulli, and radii of curvature on the calculated pressure distribution and film thicknesses have been investigated. The results indicate that the viscosity of lubricant, the sliding velocity of ball, and the reduced radius of curvature have considerable effects on the minimum and central film thicknesses. Solutions obtained with the multigrid analysis are compared with results calculated according to the Hamrock ＆ Dowson relations for the minimum and central film thicknesses.

• Tribology and Lubricants
• /
• v.35 no.5
• /
• pp.300-309
• /
• 2019

Gas foil thrust bearings (GFTBs) support axial loads in oil-free, high speed rotating machinery using air or gas as a lubricant. Due to the inherent low viscosity of the lubricant, GFTBs often have super-laminar flows in the film region at operating conditions with high Reynolds numbers. This paper develops a mathematical model of a GFTB with turbulent flows and validates the model predictions against those from the literature. The pressure distribution, film thickness distribution, load carrying capacity, and power loss are predicted for both laminar and turbulent flow models and compared with each other. Predictions for an air lubricant show that the GFTB has high Reynolds numbers at the leading edge where the film thickness is large and relatively low Reynolds numbers at the trailing edge. The predicted load capacity and power loss for the turbulent flow model show little difference from those for the laminar flow model even at the highest speed of 100 krpm, because the Reynolds numbers are smaller than the critical Reynolds number. On the other hand, refrigerant (R-134a) lubricant, which has a higher density than air, had significant differences due to high Reynolds numbers in the film region, in particular, near the leading and outer edges. The predicted load capacity and power loss for the turbulent flow model are 2.1 and 2.3 times larger, respectively, than those for the laminar flow model, thus implying that the turbulent flow greatly affects the performance of the GFTB.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.34-39
• /
• 1999

IN this study when drawing a square cup blank holder pressure necessary for flange wrinkling prevention was experimentally studied. The materials used in the experiment were SPCC and SUS304 and drawing ratio was 1.62∼2.0 Two case for lubrication condition were experimented. One was without lubricant and the other was with lubrication of high viscosity.

• Polymer(Korea)
• /
• v.29 no.6
• /
• pp.565-570
• /
• 2005

Melt processing characteristics of nylon 6 (N6) has been investigated by controlling the melt viscosity in melt impregnation process. Calcium stearate (CaST) was introduced as a lubricant for N6 and the melt viscosity of N6 decreased with adding only 1 wt$\%$ of CaST. In addition, reactive blending with polycaprolactone (PCL) was carried out by lowering the melt viscosity in N6. It was found that the melt viscosity of N6 could be controlled and further melt viscosity drop could be obtained by applying phenyl phosphite (PP) and diphenyl phosphite (DPP) to enhance the transesterification between N6 and PCL. Our approaches show that the melt viscosity of N6 could be reduced without loss of thermal stability which is the critical problem in high temperature melt impregnation process of N6.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.91-92
• /
• 2002

Most studies of elsatohydrodynamic lubrication are oriented only to the measurement of film thickness itself with optical interferometer. In order to exactly investigate the characteristics of a certain lubricant under the condition of additives. especially for traction performance. it is also important to get the information of traction force as well. In this work. we developed the device for measuring friction force of EHL contact condition, which can trace the film thickness over the contact area with optical interferometer. To verify the validity of the measuring system, the friction force and film thickness under EHL condition are measured with the variation of additive ratios of viscosity Index improvers.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.85-86
• /
• 2002

For rheology investigation of lubricating oils, first phase diagrams were made from determined free volume based on density measurements and the temperature-pressure relation was estimated using the expansion coefficient of free volume and the temperature-pressure relation of the viscoelastic transition point. Next, the authors proposed the density-pressure-temperature relation and the viscosity-pressure-temperature relation of the tested oils based on the free volume and the phase diagrams. Moreover, it was shown that the Ehrenfest equation or the gradient of the phase diagram is closely related to the expansion coefficient of free volume.