• 한국세라믹학회지
• /
• 제32권6호
• /
• pp.643-652
• /
• 1995

Si-SiC-graphite composites were developed by incorporating solid lubricant graphite into Si-SiC, in the light of improving tribological properties of Si-SiC ceramics. Si-SiC-graphite composites were fabricated by infilterating silicon melt into the mixture of α-SiC, carbon black and graphite powder at 1750℃ under 3 Torr. The particle size of graphite was in the range of 150 to 500㎛, and the loading content of graphite was 0, 20, 25, 30, 35 vol% in the mixture of α-SiC and carbon black. The mechanical and tribological properties of this composites were studied. The density, hardness, flexural strength, compressive strength and Young's modulus were decreased with increasing of graphite content. An additiion of solid-lubricant graphite up to 30 vol% has improved tribological properties of Si-SiC ceramics without considerable degradation of mechanical properties.

• Tribology and Lubricants
• /
• 제37권6호
• /
• pp.203-207
• /
• 2021

This study presents the development of dielectric constant sensors to measure lubricant properties. The lubricant oil sensor is used to measure oil properties and machine conditions. Various condition monitoring methods are applied to diagnose machine conditions. Machine condition monitoring using oil sensors has advantage over other machine condition monitoring methods. The fault conditions can be noticed at the early stages by the detection of wear particles using oil sensors. Therefore, it provides an early warning in the failure procedure. A variety of oil sensors are applied to check the machine condition. Among all oil sensors, only one sensor can measure the tendency of several properties such as acidity and water content. A dielectric constant sensor is also used to measure various oil properties; therefore, it is very useful. The dielectric constant is the ratio of the capacitance of a capacitor using that material as a dielectric to that of a similar capacitor using vacuum as its dielectric. The dielectric constant has an effect on water content, contaminants, base oil, additive, and so forth. In this study, the dielectric constant sensor is fabricated using MEMS process. In the fabrication process, the shape, gap of the electrode array, and thickness of the insulation material are considered to improve the sensitivity of the sensor.

• 한국표면공학회지
• /
• 제36권2호
• /
• pp.176-184
• /
• 2003

New lubricant film of organic and inorganic composite resin was developed to improve the press formability of galvannealed steel sheets (GA) for automotive body panels. The frictional coefficient of lubricant GA steel sheets is about 20% superior to that of uncoated GA. The current range of spot welding of lubricant GA is similar to that of the uncoated GA, but the burning trace of spot welding is inferior to that of the uncoated GA in the oiling condition. The alkaline degreasability of lubricant GA shows 100% in alkaline degreasing condition of automotive company. The size and shape of the phosphated coating layer are similar to those of the uncoated GA sheet. The powdering property of the lubricant GA gives rise to 20∼50% improved property compared with the uncoated GA sheet.

• 한국추진공학회지
• /
• 제17권5호
• /
• pp.95-100
• /
• 2013

동적 기밀구조에 사용되는 고체윤활재의 선택에 있어 중요 설계 변수들은 기밀성, 내마멸성, 윤활막의 형성 등이 있다. 본 연구에서 그라파이트의 고체유할 특성에 영향을 미치는 영향인자들이 분석되었고 다양한 시험 조건들에 대하여 발생하는 마모거동이 왕복동 마모시험으로부터 얻은 결과들과 비교되었다. 또한 윤활 막들의 생성에 대한 최적조건들이 그라파이트 소재의 특성들을 평가하기 위하여 조사되었다. 마멸입자의 생성, 윤활 막의 생성, 윤활 막의 소멸의 과정을 반복하는 과정이 마모 깊이의 변화와 통하여 마모 메커니즘을 평가하였다. 따라서 그라파이트 씰의 윤활막은 마모된 표면위에 마모 입자들의 응착에 의해 발생한 윤활막이 발생되었고 이는 마모특성에 매우 유용하였다.

• 한국재료학회지
• /
• 제19권3호
• /
• pp.156-162
• /
• 2009

Lubricant-based nanofluids were prepared by dispersing carbon nanoparticles in gear oil. In this study, the effects of the particle size, shape and dispersity of the particles on the tribological properties of nanofluids were investigated. Dispersion experiments were conducted with a high-speed bead mill and an ultrasonic homogenizer, and the surfaces of the nanoparticles were simultaneously modified with several dispersants. The effective thermal conductivity of the nanofluids was measured by the transient hot-wire method, and the tribological behaviors of the nanofluids were also investigated with a disk-on-disk tribo-tester. The results of this study clearly showed that the combination of the nanoparticles, the deagglomeration process, the dispersant and the dispersion solvent is very important for the dispersity and tribological properties of nanofluids. Lubricant-based nanofluids showed relatively low thermal conductivity enhancement, but they were highly effective in decreasing the frictional heat that was generated. For nanofluids containing 0.1vol.% graphite particles in an oil lubricant, The friction coefficient in the boundary and fluid lubrication range was reduced to approximately 70% of the original value of pure lubricant.

• 한국표면공학회지
• /
• 제43권1호
• /
• pp.41-45
• /
• 2010

The effect of $MoS_2$ and graphite content on wear resistance and mechanical properties of Cu/Sn bonded diamond micro blades was comparatively investigated in terms of volume and weight fraction. For the evaluation of endurance and cutting performance, instantaneous electric power consumption and cumulative wear loss during cutting glass work piece at constant velocity were measured with the micro blades of the wide range of lubricant content. The energy consumption of blades for glass cutting decreased with the content of lubricants. Wear amount of blade in volume increased with the amount of lubricant addition. It was found to be relevant to the decrease in flexural strength and hardness with the amount of lubricants. With the same amount of lubricant content in volume fraction $MoS_2$ showed superiority in mechanical properties and cutting performance than graphite while graphite could result in stronger effect on lowering electric consumption during cutting work piece for the same weight percent fraction than $MoS_2$ because of lower density.

• Bulletin of the Korean Chemical Society
• /
• 제34권7호
• /
• pp.2044-2050
• /
• 2013

A series of poly(glycerol-succinic acid) dithiocarbamate and 1,3,4-thiadiazole dendrimers, which have potential as anti-wear oil additives, were synthesized. Their anti-wear properties in three different oils (100N, DB-51, and soybean) were evaluated using a four-ball wear tester. The results indicated that thiocarbamate dendrimers have moderate anti-wear properties in DB-51 oil, and 1,3,4-thiadiazole dendrimers exhibited good anti-wear properties in 100N and DB-51 oils. However, dithiocarbamate and 1,3,4-thiadiazole dendrimers were not effective anti-wear additives in soybean oil.

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.113-118
• /
• 2005

Small form factor optical disks for near-field optics using solid immersion lens were developed. Disk durability properties in terms of head-disk interface (HDI) properties were investigated by drag test, diamond like carbon film and lubricant film were coated on the small form factor disk to enhance HDI. Disks with glass substrates and lubricant films after heat treatment showed more durable characteristics. Coverlayers made of UV resin were uniformly coated by spin coating In which the ski-jump could not be formed by adopting outer ring technique.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.321-322
• /
• 2006

Nano-structured ceramics, which consist of structural elements with nanometer-size crystallites, are expected to show various unusual properties. We developed the novel nano-structured ceramics which consists of $Si_3N_4$ and TiN and a self-lubricant material. The ceramics was fabricated by powder metallurgy process using mechano-chemical grinding process and short-time sintering process. Each grain size of matrix and the self-lubricant particle was under about 50 nm and a few namometer. It showed high wear resistance and low friction coefficient by controlling of microstructure.

• 한국추진공학회지
• /
• 제17권3호
• /
• pp.15-20
• /
• 2013

Graphite는 고온/고압의 가스가 추진기관 내의 구동장치에 유입되지 않게 기밀 소재로 사용되며, 마모 과정에서 윤활막을 형성하여 구조물 안에서 윤활과 기밀을 돕는다. 본 연구는 기밀 소재로 사용되는 Graphite의 고온 마모 시험을 통해 고온 마모 특성을 평가하였다. 고밀도 Graphite (HK-6)에 대하여 실제 작동환경에 기초 한 온도, 미끄럼 속도, 접촉 하중 조건에 따른 마모 특성을 평가 및 고찰하였다. 마모 표면 관찰을 통해 마모 메카니즘을 파악하고 고온 마모 특성을 통하여 최적화된 작동 환경 조건에 대하여 제안 하였다. 결과적으로, 상온에서 보다 고온 환경에서 윤활막 형성에 유리 하여 마찰 계수가 비교적 낮게 나타나는 것을 알 수 있다.