• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.5
• /
• pp.63-70
• /
• 2020

In this paper, the transmit-receive module for military seekers has been designed and fabricated in 35 GHz. To increase the performance of substrates and high integration of circuits in millimeter-wave band, a 4-layer LCP(Liquid Crystal Polymer) substrate was developed. This substrate was implemented with three FCCL substrates and two adhesive layers, and a process using the difference in melting point between the substrates was used for lamination. Using a strip line and a microstrip line was confirmed by the transmission loss along the length of the substrate, and the performance of LCP substrates was validated with a power divider in 35 GHz. After confirming the performance of individual blocks such as power amplifier and low noise amplifier, a single channel Ka-band transmission/reception module was developed using a 4-layer liquid crystal polymer substrate. The transmit power of this module has above 1.1W in pulse duty 10% and has an output power of 1.1W and it has receive noise figure less than 8.5 dB and receive gain more than 17.6 dB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.5
• /
• pp.869-876
• /
• 2001

In modern wireless communication, it has been regarded as a important problem for the spectrum efficiency to utilize the limited frequency-resource efficiently. In addition, the system architecture has been designed for low cost, low power consumption and ultra-lightweight. In this paper, we directly modulated the BCPFSK with a superior spectrum efficiency using the DDS and applied the direct conversion to the system architecture. Finally, we designed a transceiver which has the 433 MHz BCPFSK output and evaluated the system performance. In the measured result, we know that as for spectrum and the power efficiency, BCPFSK method is better than conventional one. Also, the results of the designed system is 433.92 MHz in center frequency and about 33 dBc in carrier suppression ratio. And we get the better results in local oscillator leakage and the spurious of the ISM out-band the same as -69dBc and under 60dBc.

• Smart Structures and Systems
• /
• v.6 no.5_6
• /
• pp.579-593
• /
• 2010

Low-power radio frequency (RF) chip transceiver technology and the associated structural health monitoring platforms have matured recently to enable high-rate, lossless transmission of measurement data across large-scale sensor networks. The intrinsic value of these advanced capabilities is the allowance for high-quality, rapid operational modal analysis of in-service structures using distributed accelerometers to experimentally characterize the dynamic response. From the analysis afforded through these dynamic data sets, structural identification techniques can then be utilized to develop a well calibrated finite element (FE) model of the structure for baseline development, extended analytical structural evaluation, and load response assessment. This paper presents a case study in which operational modal analysis is performed on a three-span prestressed reinforced concrete bridge using a wireless sensor network. The low-power wireless platform deployed supported a high-rate, lossless transmission protocol enabling real-time remote acquisition of the vibration response as recorded by twenty-nine accelerometers at a 256 Sps sampling rate. Several instrumentation layouts were utilized to assess the global multi-span response using a stationary sensor array as well as the spatially refined response of a single span using roving sensors and reference-based techniques. Subsequent structural identification using FE modeling and iterative updating through comparison with the experimental analysis is then documented to demonstrate the inherent value in dynamic response measurement across structural systems using high-rate wireless sensor networks.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.1
• /
• pp.17-22
• /
• 2009

A switch or circulator is used for distinguishing between the paths of transmitter and receiver in TDD systems. If the isolation between Tx and Rx paths is low in TDD systems, the output signal of the ransmitter acts as an interferer to the receiver even if the transceiver operates on the receiver mode. In this paper we propose a method to get high isolation characteristics between transmitting and receiving paths in TDD systems. We implement the module with a proposed improving method to verify the effect of the isolation improvement and the experimental results are presented. The isolation improvement of above 44.8 dB over the frequency bandwidth of 30 MHz is obtained from the implemented isolation improvement module.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.67-73
• /
• 2015

This paper presents a fully integrated 3 - 5 GHz IR-UWB(impulse radio ultra-wide band) RFIC for Location based system. The receiver architecture adopts the energy detection method and for high speed sampling, the equivalent time sampling technique using the integrated DLL(delay locked loop) and 4 bit ADC. The digitally synthesized UWB impulse generator with low power consumption is also designed. The designed IR-UWB RFIC is implemented on $0.18{\mu}m$ CMOS technology. The receiver's sensitivity is -85.7 dBm and the current consumption of receiver and transmitter is 32 mA and 25.5 mA respectively at 1.8 V supply.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.3
• /
• pp.1-10
• /
• 2010

Impulse Radio Ultra-wideband (IR-UWB) system employing the short pulse has the tolerable characteristics for the multipath environment. The corresponding transceiver with low power consumption can be simply implemented. On the other hand, in the receiver side, the precise channel estimation is required for the knowledge of essence in channel due to the short period of pulse. The estimated gains and delays in channel are used in the rake receiver. The resulting parameters we search have a strong influence on the performance in the entire system. We introduce that the essential parameters can be obtained more precisely through the preamble in receiver side for the channel estimation and related technologies are presented.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.1
• /
• pp.43-51
• /
• 2012

This paper presents the design optimization technique for a phase interpolator(PI) and suggests the inductor-loaded PI structure for low power consumption suitable for high-speed applications. An analytical study leads to the design criterion composed of the process constants for the minimum power consumption and the proposed inductor-loaded PI reduces the power by half with determined bandwidth and gain of PI. Designed 7-bit PI using $0.13{\mu}m$ 1.2V CMOS technology consumes $721.2{\mu}W$ in 12GHz with inductor and the suggested optimization technique.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.219-226
• /
• 2000

In this paper, we design and implement a IF(intermediate frequency) module for WLL(wireless local loop) CDMA(code division multiple access) basestation. The implemented IF transceiver is consists of transmitter, receiver and local oscillator. The considered signal bandwidth is 10 MHz and the local carrier frequency is 40 MHz. As test results, the If transmitter output power is -5dBm $\pm3dB$when the baseband input is -10dBm $\pm3dB$, and the IF receiver output power is -10dBm $\pm3dB$when the IF input is -5dBm $\pm3dB$. Also the AGC(automatic gain control) circuit has dynamic range of 9 dB from -7dBm to +2dBm with output power 2dBm. And the group delay characteristic is analyzed by comparing the phase delay from 1 MHz to 5 MHz and the phase distortion is very low. We can conclude that this IF system can be applied to high speed data rate communication system.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.58-63
• /
• 2013

This paper presents a transceiver design for DisplayPort interface using an optical channel. By converting the electronic channel to the optical channel, the DisplayPort's main channel can provide a high-speed data transmission for long distance. The design converting the electronic channel to the optical channel in the main channel and AUX channel of the DisplayPort is presented in this paper. Futhermore, the HPD signal transmission by using AUX channel is proposed. In order to minimize power consumption, this paper also proposed a method of controlling the TX block in the main link. The proposed system is designed by a FPGA and an optical module. The FPGA used 651 ALUT(adaptive look-up table)s, 511 resisters and 324 block memory bits. The maximum operating rate of the FPGA is 250MHz. With the proposed power control scheme, 740mW of power dissipation reduction can be achieved at the main link optical TX module.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.5
• /
• pp.261-269
• /
• 2016

A high-performance transmit/receive (T/R) switch is essential for every radio-frequency (RF) device. This paper proposes a T/R switch that is designed in the CEDEC 0.13 μm complementary metal-oxide-semiconductor (CMOS) technology for 2.4 GHz ISM-band RF applications. The switch exhibits a 1 dB insertion loss, a 28.6 dB isolation, and a 35.8 dBm power-handling capacity in the transmit mode; meanwhile, for the 1.8 V/0 V control voltages, a 1.1 dB insertion loss and a 19.4 dB isolation were exhibited with an extremely-low power dissipation of 377.14 μW in the receive mode. Besides, the variations of the insertion loss and the isolation of the switch for a temperature change from - 25℃ to 125℃ are 0.019 dB and 0.095 dB, respectively. To obtain a lucrative performance, an active inductor-based resonant circuit, body floating, a transistor W/L optimization, and an isolated CMOS structure were adopted for the switch design. Further, due to the avoidance of bulky inductors and capacitors, a very small chip size of 0.0207 mm² that is the lowest-ever reported chip area for this frequency band was achieved.