• Corrosion Science and Technology
• /
• 제2권1호
• /
• pp.53-57
• /
• 2003

The MarM247 based superalloy (8wt.%Cr- 9wt.%Co- 3wt.%Ta- 1.5wt.%Hf- 5.6%wt.Al- 9.5wt.%W- Bal. Ni) specimens were diffusion aluminized by for types of pack cementation methods, and their coating structure and their high temperature oxidation resistance were investigated. The coated specimens treated at 973K in high aluminum concentration pack had a coating layer containing large hafunium rich precipitates, which were originally included in substrate alloy. After the high temperature oxidation test in air containing 30 vol.% $H_2O$ at 1273K ~ 323K, the deep localized corrosion which reached to the substrate were observed along with these hafnium rich precipitates. On the other hand, the coated specimens treated at 1323K using low aluminum concentration pack showed the coating layer without the large hafunium rich precipitates, and after the high temperature oxidation test at 1273K for 1800 ksec, it did not show the deep localized corrosion. The nickel electroplating before the aluminizing forms thick hafnium free area, and its high temperature oxidation resistance were comparable to platinum modified aluminizing coatings at 1273K.

• 청정기술
• /
• 제2권1호
• /
• pp.60-68
• /
• 1996

고정층 반응기에서 망간광석을 이용하여 저농도의 일산화탄소 산화제어반응에 대하여 고찰하였다. 고려된 실험변수는 일산화탄소 농도 (500ppm~10000ppm), 산소 농도(500ppm~99.8%)와 촉매의 온도($50{\sim}750^{\circ}C$)이다. 또한 망간광석의 특성은 Thermogravimetric Analysis(TGA), 일산화탄소에 의한 환원, Temperature Programmed Reduction(TPR)실험을 이용하여 규명하였다. 망간광석의 일산화탄소 산화력은 순수이산화망간에 비해서 단위 면적당 높은 산화력과 $750^{\circ}C$까지 가열된 후에도 산화력이 유지될 수 있는 안정된 촉매작용을 보였다. Temperature Programmed Desorption(TPD), TPR 실험과 TG 등의 분석결과 산소의 농도가 낮거나 무산소하에서 망간광석의 격자내 산소가 쉽게 제공될 수 있음을 알 수 있었다. 일산화탄소의 농도가 500~3500ppm일 때 일산화탄소의 반응차수는 0.701이며 3500~10000ppm구간에서 일산화탄소의 농도에 무관한 0차 반응이었다.

• 한국재료학회지
• /
• 제13권12호
• /
• pp.831-838
• /
• 2003

Anisotropic mesophase carbon fiber(AMCFs) was exposed to isothermal oxidation in air and $CO_2$atmosphere, and burn-off rates have measured by TGA. The microstructure changes of oxidized carbon fibers, were observed by SEM. It was observed that oxidation rate in the air is over 100 times faster than that in $CO_2$atmosphere. The activation energy obtained in air was about 43.4 Kcal/mole in the temperature range of $600∼800^{\circ}C$, and in $CO_2$was about 55.2 Kcal/mole in the temperature range of $950∼1200^{\circ}C$. Therefore, the oxidation reaction in both atmospheres was under chemical reaction regime in the above temperature ranges. It was shown that the oxidation of the AMCFs is initiated at the end of fibers at high temperature($1100^{\circ}C$) with developing the large pores, and the small pores are developed on the fiber surface at low temperature($900^{\circ}C$). In conclusion, the oxidation of the AMCFs is progressed through the imperfection.

• 한국수소및신에너지학회논문집
• /
• 제23권2호
• /
• pp.173-182
• /
• 2012

Effects of temperature, pressure, and gas residence time on methane combustion characteristics of mass produced oxygen carrier particle (OCN706-1100) were investigated in a pressurized fluidized bed reactor using methane and air as reactants for reduction and oxidation, respectively. The oxygen carrier showed high fuel conversion, high $CO_2$ selectivity, and low CO concentration at reduction condition and very low NO emission at oxidation condition. Moreover OCN706-1100 particle showed good regeneration ability during successive reduction-oxidation cyclic tests up to the 10th cycle. Fuel conversion and $CO_2$ selectivity decreased and CO emission increased as temperature increased. These results can be explained by trend of calculated equilibrium CO concentration. However, $CO_2$ selectivity increased as pressure increased and fuel conversion increased as gas residence time increased.

• 한국환경과학회지
• /
• 제18권10호
• /
• pp.1071-1077
• /
• 2009

A novel pretreatment technique was applied to the conventional Pt/alumina catalyst to prepare for the highly efficient catalyst for the preferential oxidation of carbon monoxide in hydrogen-rich condition. Their performance was investigated by selective CO oxidation reaction. CO conversion with the oxygen-treated Pt/Alumina catalyst increased remarkably especially at the low temperature below $100^{\circ}C$. This result is promising for the normal operation of the proton exchange membrane fuel cell (PEMFC) without CO poisoning of the anode catalyst. XRD analysis results showed that metallic Pt peaks were not observed for the oxygen-treated catalyst. This implies that well dispersed small Pt particles exist on the catalyst. This result was continued by high resolution transmission electron microscopy (HRTEM) analysis. Consequently, it can be concluded that highly dispersed Pt nanoparticles could be prepared by the novel pretreatment technique and thus, CO conversion could be increased considerably especially at the low temperatures below $100^{\circ}C$.

• 한국대기환경학회지
• /
• 제14권4호
• /
• pp.313-320
• /
• 1998

The most desirable diesel oxidation catalyst (DOC) should have the properties of oxidibing CO and HC effectively at low exhaust gas temperature while minimizing the formation of sulfate at high exhaust gas temperature. Precious metals such as platinum and palladium have been known to be sufficiently active for oxidizing CO and HC and also to have high activity for the oxidation of sulfur dioxide (SO2) to sulfor trioxide (SO3). There is a need to develop a highly selective catalyst which can promote the oxidation of CO and HC efficiently, but, on the other hand, suppress the oxidation of SO2. One approach to solve this problem is to load a base metal such as vanadium in Pt-based catalyst to suppress sulfate formation. In this study, a Pt-V catalyst was prepared by impregnating platinum and vanadium onto a Ti-Si wash coated catalyst in a laboratory reactor by changing the formulations and reaction temperatures.

• 한국대기환경학회지
• /
• 제6권1호
• /
• pp.57-72
• /
• 1990

The oxidation of carbon monoxide on a catalyst, $LaSrNiCoO_3$ was investigatigated with a plug flow system. Kinetic quantities such as reaction-rate, reaction order and Arhenius-parameters at various reactor temperature from 200$^\circ$C to 300$^\circ$C were determined. Also, the optimum condition for the oxidation of carbon monoxide with this catalyst was determined and are as follows. Partial pressure of oxigen ; 428mmHg Partial pressure of carbon monoxide ; 332mmHg Mixed moral ratio of oxigen and Carbon monoxide ; 1.3 : 1 Total gas flow ; 224ml/min Reaction temperature ; 340$^\circ$C The reaction kinetic equation at the optimum condition, temperature range from 200$^\circ$C to 340$^\circ$C, are as follow. $$ $v = Ae^{6.5Kcal/RT} [CO]^{0.93 \sim 0.98} [O_2]^{0.42 \sim 0.50}$ $$ In addition to this, numerical calculation were performed to evaluate the mass and heat transfer effect on this system.

• 한국안전학회지
• /
• 제19권4호
• /
• pp.74-79
• /
• 2004

[ $CO_3O_4/{\gamma}-Al_2O_3$ ] catalysts were reported high activity on the low temperature CO oxidation. The effects of the calcination temperature, the loaded amount of cobalt and the oxygen concentration on the characteristics of CO oxidation have been investigated for a emergency escape mask cartridge. $Co(NO_3)_2\cdot6H_2O$ was used as cobalt precursor and the catalysts were prepared by incipient wetness impregnation. TGA shows that enough calcination is accomplished at $450^{\circ}C$ and cobalt phase is $Co_3O_4$ after calcination in the temperature range of $300\ ~500^{\circ}C$. The specific surface area and pore volume of catalysts are decreased with increasing of loaded amount of cobalt. And with the increase of loaded amount of cobalt and the oxygen concentration, the catalytic activity is increased.

• 한국안전학회지
• /
• 제21권2호
• /
• pp.35-45
• /
• 2006

Cobalt catalysts for gas mask loaded on various supports such as $Al_{2}O_{3},\;TiO_{2}$, AC(activated carbon) and $SiO_{2}$ were used to examine influences of calcination temperatures and reaction temperatures for CO oxidation. $Co(NO_{3})_2{\cdot}6H_{2}O$ was used as cobalt precursor and the catalysts were prepared by incipient wetness impregnation. The catalysts were characterized using XRD, TGA/DTA, TEM, $N_{2}$ sorption, and XPS. For the catalytic activity, support was in the order of ${\gamma}-Al_{2}O_{3}>TiO_{2}>SiO_{2}>AC\;and\;Al_{2}O_{3}$. The catalytic activity at lower temperature than $80^{\circ}C$ showed that with the increase of reaction temperature, cobalt catalysts on ${\gamma}-Al_{2}O_{3},\;TiO_{2},\;AC\$ has the negative activation energy but that of $SiO_{2}$ was positive.

• 대한기계학회논문집B
• /
• 제31권10호
• /
• pp.855-859
• /
• 2007

Hydrogen as an energy carrier in fuel cell offers perhaps the largest potential benefits of reduced emissions of pollutants and greenhouse gases. The generation of high-purity hydrogen from hydrocarbon fuels is essential for efficient operation of fuel cell. Reduction of carbon monoxide to an acceptable level of 10ppm involves high temperature and low temperature water gas shift (WGS), followed by selective oxidation of residual carbon monoxide. The WGS reactor was designed and tested in this study to produce hydrogen-rich gas with CO to less than 5000 ppm. In the water gas shift operation, gas emerges from the reformer is taken through a high temperature shift (HTS) catalyst to reduce the CO concentration to about $2{\sim}4%$ followed to about 5000 ppm via a low temperature shift (LTS) catalyst.