• 한국정밀공학회지
• /
• 제16권4호통권97호
• /
• pp.37-45
• /
• 1999

Many automated welding equipment are used in the industry. However, there are some problems to get quality welds because of the geometric error, thermal distortion, and incorrect joint fit-up. These factors can make the gap between base plates in case of a thick plate welding. The welding product with the quality welds can not be obtained without consideration of the gap. In this paper, the robot path and welding conditions are modified to get the quality weld by detecting the position and size of the gap. In this work, a low-priced laser range sensor is used. The 3-dimensional information is obtained using the motion of a robot, which holds a laser range sensor. The position and size of the gap is calculated using signal processing of the measured 3-dimensional information of joint profile geometry. The data measured by a laser range sensor is segmented by an iterative end point method. The segmented data is optimized by the least square method. The existence of gap is detected by comparing the data with the segmented shape of template. The effects of robot measuring speed and gap size are also tested. The recognizability fo the gap is verified as good by comparing the real joint profile and the calculated joint profile using the signal processing.

• 한국레이저가공학회지
• /
• 제17권2호
• /
• pp.19-25
• /
• 2014

Optical embedded diffraction gratings with the bulk modification in BK-7 glass plates excited by tightly focused high-intensity femtosecond (130fs) Ti: sapphire laser (peak wavelength = 790nm) were demonstrated. The structural modifications with diameters ranging from 400nm to $4{\mu}m$ were photo-induced after plasma formation occurred upon irradiation with peak intensities of more than $1{\times}1013W/cm^2$. The graded refractive index profile was fabricated to be a symmetric around from the center of the point at which low-density plasma occurred. The maximum refractive index change was estimated to be $1.5{\times}10^{-2}$. The two optical embedded gratings in BK-7 glass plate were demonstrated with refractive index modification induced by the scanning of low-density plasma formation.

• 한국전자파학회논문지
• /
• 제20권12호
• /
• pp.1233-1242
• /
• 2009

본 논문에서는 도체 판 대신 인공 자기 도체를 반사판으로 이용하여 방사 특성이 개선되고 두께를 줄인 PCS용 기지국 안테나 구조를 제안하였다. 반사판으로 도체 판을 사용하는 기존 기지국 안테나의 경우, 도체 판 끝부분에서 기생 방사가 발생하고 이는 안테나의 후방사를 증가시켜 기지국 안테나의 방사 특성을 악화시킨다. 하지만 인공 자기 도체를 사용하면 표면에서의 높은 임피던스에 의해 표면파가 억압되어 후방사를 크게 줄일 수 있다. 그리고 부엽 특성도 개선되어 서비스 지역이 겹치는 문제를 막을 수 있다. 뿐만 아니라, 인공 자기 도체 표면에서의 $0^{\circ}$ 반사 위상에 의해 기지국 안테나의 두께를 또한 줄일 수 있다.

• Journal of the Korean Wood Science and Technology
• /
• 제48권5호
• /
• pp.581-590
• /
• 2020

Pulp refining is the major way to alter the properties of fibers and formed paper. Different combinations of the bar profile of the rotor and stator during low consistency refining processes directly affect the properties of the paper. In this study, a mixture of softwood and hardwood pulp was refined by varying the bar angle of the stator while that of the rotor is fixed at 0º. The pulp samples were collected at different refining times. Then, the pulp and paper properties, such as beating degree, fiber external fibrillation, and tensile and tear indexes were measured to explore the effects of the combined refining plates at different bar angles on paper properties. The results of the experiment show that the combined refining plate of 0º and 5º recorded the most significant improvement in the pulp beating degree and fiber external fibrillation. This consequently increased the fiber bonding area, which in turn, improved both the tensile and the tear indexes of the paper. Also, the influence of the combined refining plates with a larger bar angle on the paper properties was weaker compared to that of smaller angles. This study not only provides ideas for the bar profile design but also improves the optimal selection of refining plates.

• 한국전자파학회논문지
• /
• 제14권8호
• /
• pp.855-862
• /
• 2003

본 논문에서 제안하는 안테나는 기존 내장형 안테나의 일종인 PIFA의 단점으로 협대역 문제를 해결하기 위하여, 복사 소자와 접지면 사이에 단락판을 위치시키는 변형된 안테나 형태인 PIFA(Planar Inverted-FAntenna) 구조를 제안하였다. 또한 보다 넓은 대역폭을 가지도록 방사 패치에 톱니모양의 perturbation을 주었다. 제안된 방식으로 단말기에 내장형으로 사용하기 위하여 안테나의 높이(h=0.015λ)를 최소한으로 하여 원하는 대역폭(5.2 %)을 얻었다. slim형으로 하기 위해 안테나의 특성을 급전위치(Yf, Zf), 단락 스트립(Short plate)의 위치 (Zs), 폭 (Ws), perturbation폭(w), 길이(d), 단락 스트립 높이(h), 유전율 변화($\varepsilon$$_{r}$)가 안테나에 어떤 변화를 미치는지를 조사하였다. 또한 기존 PIFA 안테나와의 대역을 비교하고, 제안된 패턴을 H, E plane으로 나타내었다. 논문의 객관성을 입증하기 위하여 FIM(Finite Integration Method) 방식에 기반인 MWS(Microwave Studio) 소프트웨어를 이용하여 Simulation 하였으며, 각각의 구조 파라미터 변화에 따른 안테나 특성을 분석하였다. 그리고 실제 제작한 안테나의 실험결과와 비교하여 증명한 결과, 제안된 방식의 PIFA 안테나 실용화가 가능성을 확인하였다..

• 천문학회보
• /
• 제35권2호
• /
• pp.52.2-52.2
• /
• 2010

107P/(4015) Wilson-Harrington is one of possible candidates of the dormant or inactive comet nuclei. It was discovered on a photographic plate exposed with the 48-inch Schmidt at Palomar Observatory on 1949 November 19 UT, displaying the faint extended cometary tail. No comet activity has not been after 1949 apparition. Here we present the optical observations of 107P/(4015) Wilson - Harrington during 2009/2010 apparition taken in search of low-level comet activity. Our photometric and spectroscopic data were collected 28 - 86 days after the perihelion passage on 2009 October 22 in a wide range of solar phase angle of 39-68 degree. A disk-integrated phase function was constructed, giving a geometric albedo of 0.055+/-0.012, phase integral of q=0.34, and Bond albedo of A_B=0.019. The photometric property shows profile similar to low albedo asteroids and comet nuclei. Any emission lines were found in our spectrum, giving a flat reflectance similar to low albedo asteroids. Although we could not find any evidence for the comet activity in our photometric and spectroscopic data, we found an upper limit of the fractional active area of 0.001%. We derived the upper limit of the optical depth of the dust trail and tail 7x10^{-10}. We conclude that 107P/(4015)Wilson-Harrington became completely dormant or inactive in 2009/2010 return.

• Asian-Australasian Journal of Animal Sciences
• /
• 제33권9호
• /
• pp.1470-1476
• /
• 2020

Objective: This study was carried out to investigate physicochemical properties, and antioxidant and antimicrobial activities of low-fat sausages (LFSs) covered with sodium alginate (SA) film alone and with powder film (TSA-film) formed by cross-linking cherry tomato powder (CTP) and SA with calcium chloride (CaCl₂). Methods: Sausages covered with the biodegradable film were assessed based on the measurement of pH, color (L^⋆, a^⋆, b^⋆), proximate analysis, expressive moisture (EM), texture profile analysis, total plate counts (TPC), violet red bile, and 2-Thiobarbituric acid reactive substances (TBARS) during storage under refrigeration. LFSs wrapped with TSA-film were compared with those wrapped with SA-film and without film (control) during storage at 10℃ for 35 days. Results: The LFSs covered with the mixed film had lower pH, lightness (L^⋆), EM%, TBARS, and TPC, but lower yellowness (b^⋆) and hardness values than those wrapped with TSA-film alone. Conclusion: Lipid oxidation and microbial growth was retarded in sausages covered with biodegradable films, especially multiple films as compared to single film, thereby resulting in extended shelf-life of the LFSs.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.494-499
• /
• 2011

One of the devices to prevent separated flow over a wing or a flap at high angle of attack is a vortex generator. In the present work, we numerically study the flow around a low-profile or micro vortex generator whose height is less than local boundary layer thickness which can delay separation with a minimum drag penalty owing to its very small wetted surface area. As a first step toward a parametric study to efficiently design this MVG flow control system, we simulate the flow around a single MVG on a flat plate. For the simulation, we employ OpenFOAM with Launder-Sharma ${\kappa}$-epsilon model. The analysis results are validated by comparing with experimental results of a rectangular MVG at an angle of attack of 10 degrees whose height is 20% of local boundary layer. Important results and aspects of this numerical study are discussed. We also simulate the flow around rectangular, triangular and trapezoidal MVGs and the results are compared

• 수산해양기술연구
• /
• 제30권2호
• /
• pp.109-115
• /
• 1994

This paper presents a new concept to reduce turbulent frictional drag by injecting micro-bubble into near the buffer layer of turbulent boundary layer on flat plate. The concentrations of micro bubble distribution in the boundary was calculater by eddy viscosity equations in the governing equations. When near region of the buffer layer of turbulent boundary layer is filled with micro-bulle of air and viscous of the region is kept low, the velocity profile in the near region should be changed substantially. Then the Reynolds stress in the region becomes less, which guide to lower velocity gradient there. It results in reduction of velocity gradient at the viscous sublayer, which gives the reduction of shear stress at the wall.

• 수산해양교육연구
• /
• 제5권2호
• /
• pp.128-137
• /
• 1993

This paper presents a new concept to reduce turbulent frictional drag by injecting micro-bubble into buffer layer of turbulent boundary layer on flat plate. The buffer layer of boundary was specified by minus velocity gradient of law of the wall. When the buffer layer region of turbulent boundary layer is filled with micro-bubble of air and viscous of the region is kept low, the velocity profile in the region should be changed substantially. Then the Reynolds stress in the buffer layer region becomes less, which guide to higher velocity gradient there. It results in reduction of velocity gradient at the viscous sublayer, which gives the reduction of shear stress at the wall.