• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.116.1-116.1
• /
• 2011

Materials with a combination of high electrical conductivity and optical transparency are important components of many electronic and optoelectronic devices such as liquid crystal displays, solar cells, and light emitting diodes. In this study, to fabricate a low-resistance and high optical transparent electrode film for organic photovoltaic, the following steps were performed: the design and manufacture of an electroforming stamp mold, the fabrication of thermal roll imprinted (TRI) poly-carbonate (PC) patterned films, the manufacture of high-conductivity and low-resistance Ag paste which was filled into patterned PC film using a doctor blade process and then coated with a thin film layer of conductive polymer by a spin coating process. As a result of these imprinting processes the PC films obtained a line width of $10{\pm}0.5{\mu}m$, a channel length of $500{\pm}2{\mu}m$, and a pattern depth of $7.34{\pm}0.5{\mu}m$. After the Ag paste was used to fill part of the patterned film with conductive polymer coating, the following parameters were obtained: a sheet resistance of $9.65{\Omega}$/sq, optical transparency values were 83.69 % at a wavelength of 550 nm.

• Progress in Superconductivity
• /
• 제8권2호
• /
• pp.175-180
• /
• 2007

High temperature superconductor $YBa_2Cu_3O_{7-x}$ (YBCO) films have been grown by in-situ electron beam evaporation on artificial metal tapes such as ion-beam assisted deposition (IBAD) and rolling assisted biaxially textured substrates (RABiTS). Deposition rate of the YBCO films is $10{\sim}100{\AA}/sec$. X-ray diffraction shows that the films are grown epitaxially but have inter-diffusion phases, like as $BaZrO_3\;or\;BaCeO_3$, at their interfaces between YBCO and yttrium-stabilized zirconia (YSZ) or $CeO_2$, respectively. Secondary ion mass spectroscopy depth profile of the films confirms diffused region between YBCO and the buffer layers, indicating that the growth temperature ($850{\sim}900^{\circ}C$) is high enough to cause diffusion of Zr and Ba. The films on both the substrates show four-fold symmetry of in-plane alignment but their width in the -scan is around $12{\sim}15^{\circ}$. Transmission electron microscopy shows an interesting interface layer of epitaxial CuO between YBCO and YSZ, of which growth origin may be related to liquid flukes of Ba-Cu-O. Resistivity vs temperature curves of the films on both substrates were measured. Resistivity at room temperature is between 300 and 500 cm, the extrapolated value of resistivity at 0 K is nearly zero, and superconducting transition temperature is $85{\sim}90K$. However, critical current density of the films is very low, ${\sim}10^3A/cm^2$. Cracking of the grains and high-growth-temperature induced reaction between YBCO and buffer layers are possible reasons for this low critical current density.

• 한국분무공학회지
• /
• 제23권4호
• /
• pp.192-204
• /
• 2018

In this study, a 3D CFD analysis method for the combustion process was established for a low calorific value syngas-diesel dual-fuel engine operating under very lean fuel-air mixture condition. Also, the accuracy of computational analysis was evaluated by comparing the experimental results with the computed ones. To simulate the combustion for the dual-fuel engine, a new dual-fuel chemical kinetics set was used that was constituted by merging two verified chemical kinetic sets: n-heptane (173 species) for diesel and Gri-mech 3.0 (53 species) for syngas. For dual-fuel mode operations, the early stage of combustion was dominated by the fuel burning inside or near the spray plume. After which, the flame propagated into the syngas in the piston bowl and then proceeded toward the syngas in the squish zone. With the baseline injection system and piston shape, a significant amount of unburned syngas was discharged. To solve this problem, effects of the injection parameters and piston shape on combustion characteristics were analyzed by calculation. The change in injection variables toward increasing the spray plume volume or the penetration length were effective to cause fast burning in the vicinity of TDC by widening the spatial distribution of diesel acting as a seed of auto-ignition. As a result, the unburned syngas fraction was reduced. Changing the piston shape with the shallow depth of the piston bowl and 20% squish area ratio had a significant effect on the combustion pattern and lessened the unburned syngas fraction by half.

• 치위생과학회지
• /
• 제22권3호
• /
• pp.139-147
• /
• 2022

Background: Temporary crown resins are used prior to prosthesis placement, indicating the importance of aesthetics. The aim of this study was evaluate the color stability of various staining solutions according to the color of temporary crown resins using VITA Easyshade^Ⓡ V. Methods: The temporary crowns used were the powder-liquid type and included four shades. A total of 36 specimens were fabricated in the form of disks with a diameter of 1.8 mm and a depth of 2 mm. They were divided into four groups of nine each, and staining was performed for seven days by precipitation in 3 mL of three staining solutions composed of distilled water, black coffee, and red wine. Color and color stability evaluations were performed by a trained examiner using a digital spectrophotometer (VITA Easyshade^Ⓡ V). Color stability was analyzed using the ΔE value. Results: Because of the color stability evaluation using the ΔE value, the difference between three and seven days was significant in the specimen I and III groups (p<0.05). Further, post hoc analysis showed that the ΔE value of red wine was significant, indicating that the color stability in red wine was low. The ΔE values in group II between days three and seven were statistically significant (p<0.05). Post hoc analysis showed that distilled water, coffee, and wine had the highest ΔE values on day three. On day seven, the ΔE value for wine was significant, and the color stability was low. There was no significant difference in group IV according to the staining period and staining solution; therefore, color stability was high (p>0.05). Conclusion: This study showed that most temporary resin restorations exhibited color stability in the staining solution. The darker the color of the temporary resin restoration, the higher the color stability against extrinsic staining.

• 대한토목학회논문집
• /
• 제2권2호
• /
• pp.39-46
• /
• 1982

회전원판접촉법(回轉圓板接觸法)에 의한 폐수처리(廢水處理)의 이해(理解)를 증진(增進)시키고 여러가지 조건(條件)의 변화(變化)에 따라 달라지는 처리효율(處理效率)을 산정(算定)하기 위하여 모형(模型)을 개발(開發)하고 Simulation을 통하여 정상상태(定常狀態)와 비정상상태(非定常狀態)에서의 모형(模型)을 분석(分析)하였다. 회전원판(回轉圓板)에 의한 기질제거모형(基質除去模型)은 용액(溶液)으로부터 미생물막내부(微生物膜內部)로의 기질전달(基質傳達)과 미생물(微生物)에 의한 기질(基質)의 분해(分解)에 의해 처리(處理)가 이루어진다고 가정(假定)하고 정립(定立)되었고 모형(模型)은 여러개의 요소(要素)로 나뉘어진 액체막(液體膜)과 미생물막(微生物膜), 그리고 용액중(溶液中)의 기질농도(基質濃度)에 관한 일련의 물질수지식(物質收支式)으로 구성(構成)된다. 정상상태(定常狀態)에서 처리효율(處理效率)은 기질(基質)의 확산계수(擴散係數)와 미생물(微生物)의 최대기질분해율(最大基質分解率)에 의해 좌우(左右)되고 확산(擴散)에 의한 영향은 용액중(溶液中)의 기질농도(基質濃度)가 낮고 최대기질분해율(最大基質分解率)이 높을 경우 현저하게 나타난다. 기질제거효율(基質除去效率)은 미생물막(微生物膜)의 두께가 얇을 때는 거의 두께에 비례(比例)하여 증가(增加)하나 두께의 증가(增加)에 따라 효율증가(效率增加)는 둔화(鈍化)되고 한계(限界)두께에 이르면 기질(基質)의 침투(浸透)가 불충분(不充分)하여 효율(效率)은 일정(一定)해진다. 비정상상태(非定常狀態)에서 유출수(流出水)의 수질(水質)은 반응조(反應槽)의 체적(體積)에 의해 영향을 받는다. 반응조(反應槽)의 체적증가(體積增加)는 첨두부하(尖頭負荷)에 대하여 첨두농도(尖頭濃度)를 낮게하는 완충효과(緩衝效果)를 나타내기 때문에 반응조(反應槽)는 균등조(均等槽)의 역할을 한다 할 수 있다.

• 한국지반환경공학회 논문집
• /
• 제20권2호
• /
• pp.59-67
• /
• 2019

전남 남해안 지역인 광양항 동측배후단지 연약지반에서 수행한 실내시험, 현장베인시험 및 피에조콘 관입시험 결과를 이용하여 연약지반의 공학적 특성을 규명하고, 피에조콘계수 산정을 위해 최적의 피에조콘 관입시험 심도를 결정하였다. 본 논문에서 이용한 자료는 61개의 실내시험과 226회의 현장베인시험, 피에조콘 관입시험 26개소이다. 실내시험 분석 결과 남해안의 다른 지역에 비해 비중, 함수비, 액성한계 및 소성지수 등의 물리적 특성이 높게 나타나며, 일축압축강도와 비배수전단강도의 역학적 특성은 넓은 범위로 분포하고 비교적 작은 값을 나타냈다. 소성도에 의한 흙 분류 결과 소성이 큰 무기점토(CH)와 소성이 작은 무기점토(CL)로 분류되었으며, Robertson(1990) 분류도표에 의한 흙 분류 결과 대부분 Type 3인 점성토에 해당하였다. 현장베인시험으로 구한 비배수전단강도를 기준으로 경험적 방법에 의해 피에조콘계수를 산정했다. 이를 위해 현장베인시험 측정심도와 비교되는 피에조콘 관입시험의 적정 측정심도 범위를 설정하기 위해 3가지 심도범위로 상관성을 분석한 결과 베인 길이의 5배 범위 측정값의 평균을 사용하는 것이 높은 상관성을 보여준다.

• 융합신호처리학회논문지
• /
• 제19권2호
• /
• pp.61-67
• /
• 2018

용접예열은 본 용접 전에 금속이 융착되는 모재면을 일정한 온도로 가열하는 것을 의미한다. 냉각속도 조절에 따른 재료 경화 정도 감소, 불순물 편석억제, 열적 변형방지, 그리고 수분제거 등 인접 영향부의 균열을 방지할 수 있다. 이러한 이유에서 고품질의 용접을 위하여 반드시 필요한 작업이다. 유도가열은 전자기유도 현상을 응용하여 전기에너지를 열에너지로 변환시키는 효율적인 가열방식이다. 기체 및 액체를 이용한 연소발열과 비교하여 신속한 가열뿐만 아니라 청결하고, 안정적이며, 경제적이다. 단순한 구조로 주파수와 코일의 형태를 변형하여 가열체의 형상, 깊이, 재질에 관계없이 가열할 수 있다. 본 논문에서는 유도가열 기법을 이용하여 저주파 용접예열 시스템을 구현하였으며, 3종의 자동차 변속기 부품을 대상으로 권선코일 내에서 각 변속기 높이에 따라 권선코일 저항, 인덕턴스 및 자동차 변속기 부품의 온도변화를 관찰한 결과 전류의 변화는 저주파 가열에 있어 매우 중요한 요인으로 작용함을 확인하였다.

• 자원환경지질
• /
• 제2권4호
• /
• pp.1-21
• /
• 1969

The Sin po fluorite deposit is of a fissure vein type which strikes $N75^{\circ}E$, dips $80^{\circ}SE$, and is embedded in the pre-Cambrian crystalline schist. The vein is 1 meter in average in thickness, about 800 meters in length and nearly 400 meters in depth. Narrow veins of crustified fluorites and agatic quartz are discontinuously embedded in the quartz gangue. Two-phase fluid inclusions, which are available for the homogenization method by using the Heating Stage Microscope 350, are found in the fluorite crystals. Most of the fluid inclusions are primary in origin and mainly composed of liquid phase associated with minor gas phase. They are tetrahedral, rounded-tubular, wedge shaped, rectangulartrapezoid, and irregular in shape. The maximum diameter of inclusions is 0.5mm and the minimum, 0.03mm, ranging from 0.2mm to 0.08mm in an average. The homogenization temperatures obtained from the test are $135-147^{\circ}C$, $125-138^{\circ}C$, $121-137^{\circ}C$, $116-133^{\circ}C$ and $106-128^{\circ}C$ in greenish, bluish, violet, light grayish blue, colorless and pinkish fluorites respectively. The range of formation temperatures of fluorites is $106-147^{\circ}C$. Therefore, the fluorite deposit of Sinpo Mine is considered to be of low temperature hydrothermal origin. The isothermal lines were drawn on the longitudinal section of the vein from the data of homogenization test. According to the results, the central and lower parts of the ore shoot in the west ore body show the higher temperatures of $130-138^{\circ}C$ and the peripheral and upper parts of it show the lower temperatures of $108-128^{\circ}C$. It seems that the isothermal trend roughly coinside with the pitch of the ore shoot.

• 한국재료학회지
• /
• 제20권11호
• /
• pp.559-569
• /
• 2010

The liquid-phase sintering method was used to prepare a glass lens forming core composed of SiC-$Al_2O_3-Y_2O_3$. Spark plasma sintering was used to obtain dense sintered bodies. The sintering characteristics of different SiC sources and compositions of additives were studied. Results revealed that, owing to its initial larger surface area, $\alpha$-SiC offers sinterability that is superior to that of $\beta$-SiC. A maximum density of $3.32\;g/cm^3$ (theoretical density [TD] of 99.7%) was obtained in $\alpha$-SiC-10 wt% ($6Al_2O_3-4Y_2O_3$) sintered at $1850^{\circ}C$ without high-energy ball milling. The maximum hardness and compression stress of the sintered body reached 2870 Hv and 1110 MPa, respectively. The optimum ultra-precision machining parameters were a grinding speed of 1243 m/min, work spindle rotation rate of 100 rpm, feed rate of 0.5 mm/min, and depth of cut of $0.2\;{\mu}m$. The surface roughnesses of the thus prepared final products were Ra = 4.3 nm and Rt = 55.3 nm for the aspheric lens forming core and Ra = 4.4 nm and Rt = 41.9 for the spherical lens forming core. These values were found to be sufficiently low, and the cores showed good compatibility between SiC and the diamond-like carbon (DLC) coating material. Thus, these glass lens forming cores have great potential for application in the lens industry.

• Geomechanics and Engineering
• /
• 제16권2호
• /
• pp.125-140
• /
• 2018

Tianjin, which is located on the west shore of the Bohai Sea, is part of China's Circum-Bohai-Sea Region, where very weak clay is deposited. From the 1970s to the early $21^{st}$ century, Tianjin marine clay deposits have been the subject of numerous geotechnical investigations. Because of these deposits' geological complexity, great depositional thickness, high water content, large void ratio, excessive settlement, and low shear strength, the geotechnical properties of Tianjin marine clay need to be summarized and evaluated based on various in situ and laboratory tests so that Tianjin can safely and economically sustain more infrastructure in the coming decades. In this study, the properties of Tianjin marine clay, especially its consolidation properties, are summarized, evaluated and discussed. The focus is on establishing correlations between the geotechnical property indexes and mechanical parameters of Tianjin marine clay. These correlations include the correlations between the water content and the void ratio, the depth and the undrained shear strength, the liquid limit and the compression index, the tip resistance and the constrained modulus, the plasticity index and the ratio of undrained shear strength and the preconsolidation pressure. In addition, the primary consolidation properties of Tianjin marine clay, such as the intrinsic compression line (ICL), sedimentation compression line (SCL), compression index, $C_c$, coefficient of consolidation, $C_v$, and hydraulic conductivity change index, $C_{kv}$, are evaluated and discussed. A secondary consolidation property, i.e., the secondary compression index, $C_a$, is also investigated, and the results show that the ratio of $C_a/C_c$ for Tianjin marine clay can be used to calculate $C_a$ in secondary consolidation settlement predictions.