• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.1
• /
• pp.3293-3301
• /
• 1974

An experimental work was conducted by using a laboratory-made model dryer to investigate the effect of the rate of natural forced-air on the drying rate of rough rice which was deposited in the deep-bed. The dryer consisted of 8 cylinderical containers with grain holding screen at their bottoms, each of which having 30cm in diameter and 15cm in height. The containers were sacked vertically with keeping them air-tight by using paper tape during dryer operation. Two separate layers of containers were operated in the same time to have two replications. The moisture contents of grains within each bins after predetermined period of dryer operation were determined indirectly by measuring the weight of the individual containers. The air-rates were maintained at 6 levels, or 5, 8, 10, 15, 18 and 20 millimenters of static head of water. The roomair conditions during dryer operation were maintained in the range of 10-l5$^{\circ}C$ in temperature and 40-60% in relative humidity. The results of the study are summarized as follows: 1. Drying characteristics of the grains in the bottom layers were approximately the same regardless of airdelivery rates, giving the average drying rate as about 0.35 percent per hour after 40-hour drying period, during which moisture content (w. b.) reduced from 24 percent to about 10 percent. 2. After about 40-hour drying period, the mean drying rates increased from 0.163 percent per hour to 0.263 percent per hour as air-flow rates increased from 5mm to 87.16mm of static head of water. In the same time, the moisture differences of grains between lower and upper layers varied from 12.7 percent at the air rate of 5mm of water head to 7.5 percent at the air-flow rate of 20mn of water head. Thus, the greater the air-flow rate was, the more overall improvement in drying performance was. Additionally, from the result of ineffectiveness of drying grain positioned at 70cm depth or above by the air rate of 5mm of static head of water it may be suggested in practical application that the height of grain deposit would be maintained adequately within the limits of air-rates that may be actually delivered. 3. Drying after layer-turning operation was continued for about 30 hours to test the effectiveness of reducing moisture differences in the thick layers. As a result of this layer-turning operation, moisture distribution through layers approached to narrow ranges, giving the moisture range as about 7 percent at air-flow rate of 5mm head of water, about 3 percent at 10mm head about 2 percent at 15mm head, and less than 1 percent at 20mm head. In addition, from the desirable results that drying rate was rapid in the lower layers and dully in the upper layers, layer-turning operation may be very effective in natural air drying with deep-layer grain deposit, especially when the forced air was kept in low rate. 4. Even though the high rate of air delivery is very desirable for deep-layer natural-air drying of rough rice, it can be happened that the required air delivery rate could not be attained because of limitation of power source available on farms. To give a guide line for the practical application, the power required to perform the drying with the specified air rate was analyzed for different sizes of drying bin and is given in Table (5). If a farmer selects a motor of which size is 1 or {{{{1 { 1} over {2 } }}}} H.P. and air-delivery rate which ranges from 8~10mm of head, the diameter of grain bin may be suggested to choose about 2.4m, also power tiller or other moderate size of prime motor may be recommended when the diameter of grain bin is about 5.0m or more for about 120cm grain deposit.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.7
• /
• pp.906-913
• /
• 2019

To evaluate the removal performance of PO₄-P and NH₃-N, laboratory experiments were conducted by filling a container with oyster shells, pyrolyzed at 100℃ (POS100), 600℃ (POS600) and 800℃ (POS800), and passing artificial wastewaters through the container. The pH in the ef luent was found to increase due to CaO eluted from oyster shell. Removal amounts of PO₄-P of ~23.1 mg/kg, 16.1 mg/kg, and 15.9 mg/kg were obtained when POS100, POS600, and POS800, respectively, were used; therefore, the highest PO₄-P removal amount was obtained when POS100 was used. It is considered that Ca and dolomite in the oyster shells adsorbed and precipitated PO₄-P. Removal amounts of NH₃-N were of ~3.56 mg/kg, 5.72 mg/kg, and 3.97 mg/kg were obtained when POS100, POS600, and POS800, respectively, were used The low removal rate for NH₃-N is probably due to unstable nitrification, use of sealed containers, and the effect of NH₃-N being converted to NH₄⁺ upon increasing pH. Based on these results, pyrolyzed oyster shell is expected to promote changes in PO₄-P and NH₃-N concentrations through chemical reactions. These results can also be used for basic research in the development of wastewater treatment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.77-88
• /
• 2000

In this paper, the 3-mode variable gain high power amplifier for a transmitter of INMARSAT-B operating at L-band(1626.5-1646.5 MHz) was developed. This SSPA can amplify 42 dBm in high power mode, 38 dBm in medium power mode and 36 dBm in low power mode for INMARSAT-B. The allowable errol sets +1 dBm as the upper limit and -2 dBm as the lower limit, respectively. To simplify the fabrication process, the whole system is designed by two parts composed of a driving amplifier and a high power amplifier. The HP's MGA-64135 and Motorola's MRF-6401 were used for driving amplifier, and the ERICSSON's PTE-10114 and PTF-10021 for the high power amplifier. The SSPA was fabricated by the RP circuits, the temperature compensation circuits and 3-mode variable gain control circuits and 20 dB parallel coupled-line directional coupler in aluminum housing. In addition, the gain control method was proposed by digital attenuator for 3-mode amplifier. Then il has been experimentally verified that the gain is controlled for single tone signal as well as two tone signals. In this case, the SSPA detects the output power by 20 dB parallel coupled-line directional coupler and phase non-splitter amplifier. The realized SSPA has 41.6 dB, 37.6 dB and 33.2 dB for small signal gain within 20 MHz bandwidth, and the VSWR of input and output port is less than 1.3:1. The minimum value of the 1 dB compression point gets more than 12 dBm for 3-mode variable gain high power amplifier. A typical two tone intermodulation point has 36.5 dBc maximum which is single carrier backed off 3 dB from 1 dB compression point. The maximum output power of 43 dBm was achieved at the 1636.5 MHz. These results reveal a high power of 20 Watt, which was the design target.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.1 s.129
• /
• pp.87-96
• /
• 2005

This study was carried out to evaluate the shear bond strength and adhesive bond durability of structural glued laminated timber (glulam) manufactured with mixed species lumber of Korean red pine, Korean pine and Japanese larch, using resorcinol adhesive and water-based polymeric-isocyanate adhesive (WPI). Each board used as a glulam lamina was graded by visual inspection. The visual lumber grade of the all species was very low due to the large size and number of knots and the steep slope of grain. In view of the results, appropriate pruning, sawing and drying processes might be needed to produce high grade lamina lumber with small knot size and drying defect free. Shear bond strength of every tested glulam specimen ranged between 7.9 and $9.9N/mm^2$, and much higher than the Korean Standard (KS) for glulam shear bond strength, $7.1N/mm^2$. There was not much shear bond strength difference between wood/resorcinol and wood/WPI. The resorcinol adhesive bond durability exceeded KS requirements. However, delamination on the end-grain surfaces of WPI glulam submerged in both room temperature and boiling water severely occurred, and its durability did not meet KS requirements. Further investigations may be required, and special care should be taken, to ensure long service life of WPI glulam used for exterior application. Results of this study are expected to be useful for improvement of mechanical properties and structural performance of mixed species glulam.

• Korean Journal of Breeding Science
• /
• v.41 no.3
• /
• pp.299-305
• /
• 2009

A new six-rowed naked barley cultivar "Jinjuchal" with high whiteness after cooking and high $\beta$-glucan content was developed from the cross between 'Jinmichapssalbori' with high winter hardiness, lodging tolerance, grain whiteness and pearling yield, and 'Suwon 333' with waxy endosperm by the Honam Agricultural Research Institute (HARI), NICS, RDA in 2007. An elite line, SB962002G-B-B-B-84-4 was selected in 2002 and designated as 'Iksan 79' It showed good agronomic performance in the regional yield trials (RYT) from 2005 to 2007 and was released with the name of "Jinjuchal" possessing high whiteness and low proanthocyanidin waxy endosperm. The average heading and maturing dates of "Jinjuchal" were April 27 and June 1 in paddy field, which were same and one day later than those of the check cultivar 'Saechalssalbori' respectively. The new cultivar, "Jinjuchal" had 81 cm of culm length that was 1cm longer than that of 'Saechalssalbori' and 4.9 cm of spike length. It showed 673 spikes per $m^2$, 56 grains per spike, 27.0 g of 1,000-grain weight, and 752 g of test weight. "Jinjuchal" showed stronger hardiness and better resistance to powdery mildew and BaYMV (Barley yellow mosaic virus) than those of the check cultivar, 'Saechalssalbori' It showed higher $\beta$-glucan content(8.4%) and water absorption rate than those of the check cultivar, 'Saechalssalbori' Its average yield of the pearled grain in the regional yield trial was 3.79 MT/ha in upland, and 3.73 MT/ha in paddy field, which were 1% lower and 3% higher than those of the check cultivar, respectively. Total phenol and proanthocyanidin contents were 4.2 and 0.2 mg/g, respectively. This cultivar is suitable for the area of the daily minimum temperature above $-6^{\circ}C$ in January in Korean peninsula.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.3
• /
• pp.209-213
• /
• 2019

Recently, demand for high energy density and long cycling stability of energy storage system has increased for application using with frequency regulation (F/R) in power grid. Supercapacitor have long lifetime and high charge and discharge rate, it is very adaptable to apply a frequency regulation in power grid. Supercapacitor can complement batteries to reduce the size and installation of batteries. Because their utilization in a system can potentially eliminate the need for short-term frequent replacement as required by batteries, hence, saving the resources invested in the upkeep of the whole system or extension of lifecycle of batteries in the long run of power grid. However, low energy density in supercapacitor is critical weakness to utilization for huge energy storage system of power grid. So, it is still far from being able to replace batteries and struggle in meeting the demand for a high energy density. But, today, LIC (Lithium Ion Capacitor) considered as an attractive structure to improve energy density much more than EDLC (Electric double layer capacitor) because LIC has high voltage range up to 3.8 V. But, many aspects of the electrochemical performance of LIC still need to be examined closely in order to apply for commercial use. In this study, in order to improve the capacitance of LIC related with energy density, we designed new method of pre-doping in anode electrode. The electrode in cathode were fabricated in dry room which has a relative humidity under 0.1% and constant electrode thickness over $100{\mu}m$ was manufactured for stable mechanical strength and anode doping. To minimize of contact resistance, fabricated electrode was conducted hot compression process from room temperature to $65^{\circ}C$. We designed various pre-doping method for LIC structure and analyzing the doping mechanism issues. Finally, we suggest new pre-doping method to improve the capacitance and electrochemical stability for LIC.

• Korean Journal of Breeding Science
• /
• v.43 no.6
• /
• pp.513-518
• /
• 2011

'Hongjinju', the reddish brown coloured rice variety, was developed by the rice breeding team of National Institute of Crop Science, RDA during the period from 1990 to 2006 and released in 2007. The cultivar was derived from a cross between Suwon 383, and $SR18164F_2$, a reddish brown pigmented line. 'Hongjinju' is medium maturity with 133 days of growth duration from seeding to heading and is japonica-type with about 82 cm in culm length. 'Hongjinju' has slightly less number of tillers per hill and more spikelets of panicles than those of 'Heugjinjubyeo'. It is susceptible to leaf blast, other disease and insect pests. It shows intermediate germination ratio at low temperature and similar tolerance to leaf discolor at seeding stage and heading-delay but it is resistant to spikelets-sterility type of cold damage at maturing stage compared with 'Heugjinjubyeo'. The yield performance of this variety in brown rice is about 5.07 MT/ha and is adaptable to the central and southern plain areas of Korea.

• Korean Journal of Breeding Science
• /
• v.41 no.2
• /
• pp.177-181
• /
• 2009

'Pyeongwon' is a new japonica rice cultivar which is developed from a cross between Jinbu19 and Samjiyeon4 from North Korea by the rice breeding team of National Institute of Crop Science, RDA. Pyeongwon has about 107 days duration from seeding to heading in mid-northen plain, alpine, north-eastern coastal and southern alpine areas. It has about 67 cm culm length and tolerance to lodging. Pyeongwon has 13 tillers per hill and 82 spikelets per panicle. It showed tolerance to heading delay and spikelet sterility due to cold treatment similar to Odaebyeo. It also showed slow leaf senescence and moderate tolerance to viviparous germination during the ripening stage. Pyeongwon has resistance to blast disease but susceptible to stripe virus and brown planthopper. Milled rice of Pyeongwon has translucent kernels, relatively clear non-glutinous endosperm and medium short grain. It is characterized as a low gelatinization temperature and slightly lower amylose content (17.1%) variety compared to Odaebyeo (19.5%) and has good palatability of cooked rice. The milled rice yield performance of this cultivar was about 5.28 MT/ha by ordinary culture in local adaptability test for three years. This cultivar may be highly adaptable to the mid-northen plain, alpine, north-eastern coastal and southern alpine areas of Korea.