• 대한치과보철학회지
• /
• 제39권6호
• /
• pp.682-697
• /
• 2001

This investigation evaluated the fracture toughness($K_{IC}$) of eight currently available core materials, and relate the fracture toughness value to fractography analysis and surface characteristics using a atomic force microscope (AFM). Single-edge notched (SEN) test specimens (n=10) and compact tension (CT) test specimens (n=10) were prepared conforming to the ASTM Standard E-399 for a high copper amalgam, three composite core materials (Core-Max II, Core Paste, Bisfil Core), two reinforced composite core materials (Ti-Core, Ti-Core Natural), a resin-modified glass ionomer core material (Vitremer), and a conventional glass ionomer core material (Ketac-Molar). The specimens were tested with an Instron Universal Testing Machine. The maximum loads were measured to calculate the fracture toughness ($K_{IC}$). Thereafter, fracture surfaces of SEN specimens of each material were investigated for fractography analysis using scanning electron microscope. And, disc-shaped specimens with 1mm thickness were fabricated for each material and were investigated under AFM for surface morphology analysis. The results were as follows: 1. Bisfil Core showed the highest mean fracture toughness regardless of test methods. 2. For the tooth-colored materials, Ti-Core Natural exhibited the highest fracture toughness. 3. Ketac Molar showed a significantly low fracture toughness when compared with the amalgam and the composite resin core materials(p<0.05). 4. The fracture toughness values obtained with the single-edge notched test, except Ketac Molar, were higher than those obtained in the compact tension test. 5. SEM revealed that the fracture surface of high fracture toughness material was rougher than that of low fracture toughness material. 6. AFM revealed that the surface particles of the composite resins were smaller in size, with a lower surface roughness than the glass ionomer core materials.

• Journal of Welding and Joining
• /
• 제16권6호
• /
• pp.77-85
• /
• 1998

Effects of non-cleaning and cleaning fluxes on the wetting properties and defects at flow soldered joints were investigated. Non-cleaning flux (R-type of 3.3% solid content) and cleaning flux (RMA-type of 15% solid content) were used. Wetting test was accomplished by wetting balance method with changing surface state of wetting specimen, CU. Sn-37%Pb solder was used for wetting test and flow soldering. As experimental results, the wetting time for vertical force from the surface tension being zero was mainly affected by surface state of the wetting specimen. Non-cleaning flux had a good wettability compared with cleaning flux. In case of non-cleaning flux, conveyor speed had a great affection to defects of bridge, icicle, and poor solder.

• BMB Reports
• /
• 제36권4호
• /
• pp.367-372
• /
• 2003

The stability of four hemoglobins (Hb) in dimer forms (low concentration) were investigated by the kinetics of denaturation. The rate constants of denaturation were obtained by variation of 280 nm absorption versus time in 10 mM Tris-HCl, 10 mM EDTA, pH 8.0 at $45^{\circ}C$ in the absence and presence of 0.5 M ethanol, dimethyl sulfoxide (DMSO), formamide, and glycerol. The results show the trend of rate constants in different co-solvents in the following order: chicken hemolysate < human hemolysate and chicken Hb D < chicken Hb A. The buried surface area was calculated for Hb samples in the absence of cosolvents. Accordingly, the trend points out that: chicken Hb D > chicken Hb A > human Hb A. These results suggest that both chicken hemolysate and chicken Hb D are relatively more stable than human and chicken Hb A, respectively. However, the denaturation rate constants of Hb in different co-solvents have designated the following order: ethanol > DMSO > formamide > glycerol. As a matter of fact, this phenomenon is an indication of an increase in the denaturation capacity (DC) and hydrophobicity, and a decrease in the surface tension of the solution in the preceding co-solvents.

• 한국표면공학회지
• /
• 제33권5호
• /
• pp.387-397
• /
• 2000

Antimony in the galvanizing bath had greater effect on the growth of grains in the solidification of molten coating layer and on the decrease of its surface roughness than lead. Particularly 0.01 wt % antimony in the galvanizing bath showed much stronger effect than expected considering its low surface tension value. These effects were seemingly originated from the development of preferred orientation of (0002) plane parallel to steel surface. Antimony was found to be widely distributed in form of orderly arrangement throughout the coating layer unlike lead from the results of surface analyses on coating layers as received and on those as etched in chromating solution. In addition, supercooling in the 0.07 % antimony and the 0.2 % lead galvanizing bath was also measured to be in the range of$ 2~4^{\circ}C$ and $9~11^{\circ}C$ respectively, and it indicates that antimony forms fine dendrite expanded rapidly on the steel surface.

• 콘크리트학회논문집
• /
• 제24권1호
• /
• pp.61-70
• /
• 2012

최근 정부는 '저탄소 녹색성장 기본법'을 시행하여 국가 총체적 차원에서 에너지 절감, 온실가스 저감을 위한 노력을 기울이고 있다. 건물부문에서는 건물외피와 단열재의 열적 특성을 검토하여 건물 자체의 단열성능을 높임으로써 에너지를 절감할 수 있다. 이 연구는 건물부문의 에너지 절감을 목적으로 건물에 적용 가능한 경량기포 콘크리트 단열패널을 개발하기 위한 연구로서, 기포제 종류(AES, AOS, VS, FP)와 기포제 희석농도(1%, 3%, 5%), 기포율(30%, 50%, 70%)에 따른 기포 콘크리트의 물리·역학적 특성 및 열적 특성을 검토하여 에너지 절감을 위한 단열재로서의 최적조건을 찾고자 하였다. 실험 결과, 발포율에 영향을 미치는 기포제가 포함된 수용액의 표면장력은 AOS를 사용한 경우가 다른 기포제를 사용한 경우보다 낮게 나타났다. FP는 표면장력의 저하량이 크지 않고 발포율이 낮기 때문에 저농도로 희석한 경우 다량의 수분을 함유하고 있는 안정적이지 못한 기포가 생성되어 3% 이상 사용하여야만 비교적 안정적인 기포를 만드는 것이 가능하였다. 또한, 압축강도와 열전도율은 저밀도 영역에서는 기포제 종류에 따른 차이는 발생하지 않았으나, 상대적으로 고밀도영역에서 압축강도는 AOS와 FP, 열전도율은 VS와 FP가 더 효과적인 것으로 나타났다. 또한, 기포농도와 기포율이 증가할수록 공극 크기는 커지며 열린공극을 형성하는 것으로 나타났으며 모든 기포제에 대한 열전도율은 KS기준을 만족하여 우수한 단열재로서의 가능성을 보였다. 종합적인 분석 결과, FP를 농도 3%로 사용하여 제조한 시험체가 건물에 적용시 기포 콘크리트 단열패널로서 가장 우수한 성능을 발현할 것으로 판단된다.

• 미생물학회지
• /
• 제42권4호
• /
• pp.286-293
• /
• 2006

대전일원의 유류오염 지역의 토양으로부터 원유를 단일 탄소원으로 이용하는 총 322균주를 순수분리 하였고, 이중 생물 계면활성제(biosurfactant) 생성능이 가장 우수한 한 균주를 최종 선별하여 형태 및 생리 생화학적 특성을 조사하고 16S rRNA 염기서열을 분석을 통하여 동정한 결과 Pseudomonas sp.로 확인되어 Pseudomonas sp. G314라 명명하였다. 최종 선별된 Pseudomonas sp. G314는 암피실린, 클로람페니콜, 스펙티노마이신, 스트렙토마이신 등의 항생제와 Li, Cr, Mn 등의 중금속에 대해 강한 내성을 갖고 있었고, 최적 온도와 pH는 각각 $30^{\circ}C$와 pH 7.0으로 확인되었다. Pseudomonas sp. G314가 생성하는 생물 계면활성제의 초기 표면장력은 72 dyne/cm이었으나, 배양 7시간 후 부터는 표면장력이 최대 25 dyne/cm까지 감소되었다. Pseudomonas sp. G3l4가 생산하는 생물 계면활성제를 회수하고 농축하기 위해, 산 침전 후에 유기용매로 배양액을 추출하고 이를 감압농축하여 얻은 시료를 crude biosurfactant로 사용하여 CMC (critical micelle concentration)간을 측정한 결과 20 mg/L로 확인되었다.

• 생명과학회지
• /
• 제21권1호
• /
• pp.134-140
• /
• 2011

대전일원의 유류오염 지역의 토양으로부터 원유를 단일 탄소원으로 이용하는 총 145균주를 순수분리 하였고, 이중 생물 계면활성제 생성능이 가장 우수한 한 균주를 최종 선별하여 형태 및 생리 생화학적 특성을 조사하고 16S rRNA 염기서열을 분석을 통하여 동정한 결과 Pseudomonas sp.로 확인되어 Pseudomonas sp. Z1이라 명명하였다. 최종 선별된 Pseudomonas sp. Z1은 클로람페니콜과 암피실린 등의 항생제와 리튬, 망간, 바륨 등의 중금속에 대해 강한 내성을 갖고 있었고, 최적 온도와 pH는 각각 $30^{\circ}C$와 pH 6.0-7.0으로 확인되었다. Pseudomonas sp. Z1이 생성하는 생물 계면활성제는 배양 10시간 이후부터 배양액의 표면장력이 급격히 감소해, 배양 21시간 후에 최대 28 dyne/cm까지 감소되었고, 2% 이상의 NaCl을 첨가한 경우 배양액의 생물계면활성제의 활성이 감소하였다.

• 웰빙융합연구
• /
• 제5권1호
• /
• pp.31-35
• /
• 2022

Purpose: This study was conducted to investigate the effects of change in the unstable support surface location during bridge exercise on the muscle activity of erector spinae and gluteus maximus. Research design, data and methodology: 12 healthy participants aged 23.32 ±1.02 were measured muscle activities of erector spinae and gluteus maximus during bridge exercise and compared between the exercise conditions; unstable support surface located on upper back and feet during bridge exercise. Paired t-test was performed to identify whether there was a significant difference in the muscle activities between the exercise conditions. Results: As a result, even though higher levels of the averaged muscle activities of both erector spinae and gluteus maximus during exercise in unstable support surface located on feet than upper back were observed, no significant differences were found. Conclusions: The change of unstable support surface location during bridge exercise for low back pain rehabilitation would be more appropriate to be used to increase levels of tension of muscle activities and train fine motor control rather than to strengthening muscle strength.

• 대한금속재료학회지
• /
• 제50권5호
• /
• pp.345-351
• /
• 2012

A three-point bending test was performed on roll-bonded Mg/Al/STS clad-metal plates under two different testing conditions (Mg layer in tension, or STS in tension) and their mechanical response and fracture behavior were investigated. Bending strength was found to be greater under the condition of Mg layer in tension. Heat treatment at $200^{\circ}C$ increased the bending formability, suggesting the interfacial strength increased at $200^{\circ}C$. Under the condition of Mg in tension, the clad heat-treated at $300^{\circ}C$ and $400^{\circ}C$ fractured in two steps, with the first step associated with the interfacial fracture between Mg and Al, and the second the fracture of the Mg layer. STS/Al layers were found to be bent without complete fracture. Under the condition of STS in tension, the clad heat-treated at $300^{\circ}C$ and $400^{\circ}C$ exhibited a very small load drop at the displacement, which is similar to that of the first load drop associated with the interfacial fracture under the condition of Mg in tension. In this case, no interfacial cracks were found and the complete cut-through fracture of clad was observed at low temperature heat treatment conditions, suggesting excellent interfacial strength. When the heat treatment temperature was higher than $300^{\circ}C$, interfacial cracks were observed. The local stress condition and the position of the interface with respect to the surface were found to have a great influence on the fracture behaviors of clad metals.

• 대한기계학회논문집
• /
• 제8권3호
• /
• pp.195-200
• /
• 1984

본 연구에서는 SUS 304강의 상온하의 평골재 표면에 발생. 성장하는 미소표면 피로균열의 거동을 파괴역학적 관점과 수법으로 정량적으로 조사하려는 연구의 일환 이다.