• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.13-24
• /
• 2009

This study developed a high strength and performance concrete pavement material with low shrinkage and reflection of sunlight. Based on the literature review, a new mix-design of applying flash ash to improve the strength and performance of the concrete as well as to reduce the dry shrinkage is suggested. In addition, adding black pigment to reduce the reflection and technique of applying OAG (Optimized Aggregate Gradation) is also included. The result of the laboratory experiment indicates that the brightness and the reflection, which depends on the ratio of black pigment addition, did not deviate from the normal range. When OAG is considered for the mix-design, the strength and performance of the concrete improved greatly. In addition, the mix-design using fly ash reduced the dry shrinkage of concrete and improved the resistance to the permeation of chloride ion. Furthermore, the mix-design, which uses fly ash (25% replacement) and black pigment (3% addition) with the application of OAG, is found to be the most effective mix to reduce the shrinkage and reflection as well as improving the strength and performance of the concrete. The result of an economic analysis indicates that the initial construction cost of this proposed mix is more expensive than that of normal concrete pavement material. However, it can be more economic in the long run because the normal concrete pavement material is likely to cost more due to higher probability of maintenance and repair and higher social cost due to traffic accident, etc.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.22 no.1
• /
• pp.41-48
• /
• 1986

Ifis recommended that the injection rate should be accurate and reliable in the input data of the performance simulation in diesel engine. Matsuoka Sin improved W. Bosch's injection ratio measurement system. Matsuoka Sin reduced length of the test pipe and set the orifice. However, it was not measured accurately to measure the injection ratio due to reflection wave. In the present thesis, the improved measurement system with combination of the conventional W. Bosch type injection ratio measurement system and Matsuoka Sin type corrected W. Bosch type was practically made. The location of orifice and throttle valve was modified and set one more back pressure valve in order to reduce the effect of reflection wave. The results according to injection condition of multi-hole nozzle are following: 1. Measurement error of injection ratio measurement system in this thesis was $\pm$ 1 %, therefore, its reliability was good. 2. The form of injetion ratio is changed from trapezoidal shape to triangle shape with increase of revolution per minute when injection amount is constant. 3. In the case of constant rpm, the initial injection ratio is almost constant regardless of the amount, meanwhile the injection period becomes longer with increase of the amount. 4. The injection pressure of nozzle isn't largely influenced with injection ratio in the case of constant injection amount and rpm, otherwise the initial injection amount is increased by 3-4% when the injection pressure is low. 5. The injection ratio isn't nearly influenced with back pressure.

• Journal of the Korean Vacuum Society
• /
• v.19 no.1
• /
• pp.28-35
• /
• 2010

A new electrode structure in a plasma display panel was designed in a way to increase the bright room contrast ratio (BRCR). The area of the black matrix pattern to get a low reflection from the panel surface was enlarged using the new electrode design concept. The electrical characteristics such as firing voltage, voltage margin and power consumption were measured. The luminance of the panel was measured and the luminous efficiency was calculated. It was found that the new electrode structure was very effective to enhance the BRCR.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.4
• /
• pp.224-231
• /
• 2003

In this study, the hybrid breakwater system - a breakwater system combining the floating breakwater with the submerged breakwater - is used to improve the wave screening performance that may not be achieved by using the floating breakwater or the submerged breakwater, separately. Two-dimensional finite element method is used for numerical analysis and the wave reflection ratio and the wave transmission ratio are analyzed for the proposed case. In case of using the hybrid breakwater system, wave screening performance is more effective than in case of using the floating breakwater or the submerged breakwater, separately. It also shows an effective wave screening on the long wave period and an advanced wave screening performance with low height of the submerged breakwater.

• Korean Journal of Optics and Photonics
• /
• v.7 no.4
• /
• pp.370-374
• /
• 1996

A Superstructure Grating(SSG) Distributed-Bragg-Reflector(DBR) laser has a broad tuning range with a good mode suppression ratio. However, gaps of channel are observed in the wavelength-tuning characteristics of an SSGDBR laser which employs linearly-chirped DBR mirrors. We found by numerical simulation that the gaps may be attributed to the nonuniform reflection-peak heights of a linearly-chirped DBR mirrors. We propose a nonlinearly chirped grating DBR mirror structure that makes reflection-peak heights almost uniform. Therefore a nonlinearly chirped grating structure can be employed in an extended tuning range semiconductor laser to achieve gap-free tuning and low threshold current operation simultaneously.

• Plant Resources
• /
• v.7 no.1
• /
• pp.77-86
• /
• 2004

The reduced ratio of red:far-red (R:FR) light acts as a measure of the proximity of competitors and plants can detect the potentially competing neighbor plants by perceiving reflected R:FR signals and initiate the response of “shade avoidance” before actual shading occurs. The phytochrome system is responsible for monitoring the changes in the R:FR and initiating the shade avoidance response. The response to low R:FR ratio was studied in a white aspen Populus alba clone ‘Bolleana’ using two filter systems: a clear plastic filter system that allows a R:FR ratio less than 1.0 to pass from adjacent border plant reflection; and a special commercial plastic that blocks FR light and creates a R:FR ratio above 3.0. The reduced R:FR signals enhanced the stem elongation in response to competition at the expense of relative stem diameter growth. Trees grown inside clear chambers were 27 ％ taller than trees grown inside the FR-blocking filter chambers. Stem taper of clear chamber trees was 16％ less than the FR-blocking filter trees. Low R:FR also induced 22％ more stem dry weight and 13％ greater petiole length per leaf compared to the FR-blocking filter trees. There were no statistically significant differences in leaf area, leaf number increment, and total dry weight between the two light filter treatments.

• The Journal of the Acoustical Society of Korea
• /
• v.8 no.1
• /
• pp.67-74
• /
• 1989

The reflection coefficients of the sound absorbing materials are obtained from the standing wave ratio in the standin wave tube. This method is rather laborious to find the sound pressure maximum and minimum. We devised new method for determination of the complex reflection coefficients of the materials. The sound pressures and the phases are measured at least three points along the axis of the tube. The complex reflection coefficients are determined from the measured values by least square method. The measured results for the glasswool with thickness of 5cm and density of $50kg/m^3$ and the steel plate with thickness of 1.5cm are in good agreement with those of the conventional method. It is possible to measure the complex reflection coefficients at low frequencies with short standing wave tube and to interface with the personal computer which is very useful for the handling of amount of samples.

• International Journal of Contents
• /
• v.2 no.1
• /
• pp.29-33
• /
• 2006

The common-source low noise amplifier(LNA) with inductive degeneration using a genetic algorithm is designed and tested for a down converter in an industrial, scientific and medical (ISM) band application and a wireless broadband internet service (WiBro). The genetic algorithm optimizes the reflection coefficients to be well matched the input and output ports between multistage transistor amplifiers, and it generates low voltage standing wave ratio as well as gain flatness of the amplifier. The stability and the gain flatness of the LNA have been improved by combining the matching circuits and the series feedback microstrip lines with inductive degeneration at common-source port. In the frequency range of ISM band and WiBro application operating at $2.3GHz{\sim}2.5GHz$, the measured power gain and maximum voltage standing wave ratio (VSWR) of the LNA are $41{\pm}0.5dB$ and 1.3, and the noise figure of the LNA is lower than 0.85dB. The above results are agreed well with the theoretical values of the amplifiers.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.4
• /
• pp.798-805
• /
• 2017

This paper presents a low profile multi circular ring with different radius, patch antenna with modified feed line and slotted ground. The size of the antenna is $15{\times}12mm^2$, having electrical dimensions of $0.14{\lambda}{\times}0.12{\lambda}$ (at lower initial frequency) and footprints of $180mm^2$. The proposed antenna covers 3.1 to 12.3 GHz, reflection coefficient up to -38 dB with Bandwidth ratio of 4.13:1 and fractional Bandwidth of 122%. Bandwidth dimension ratio has been calculated (which is 6246) as a proof for compact size. Thin slots introduced on the feed line provide good impedance matching for whole frequency band. Numerical simulations of the proposed antenna are reported in terms of reflection coefficient ${\leq}-10dB$, vswr 2:1, radiation pattern and group delay (ns). The proposed antenna has advantage of very small size along with better impedance match that provides a practical approach to realize it for BW enhancement and UWB applications.

• Current Optics and Photonics
• /
• v.1 no.1
• /
• pp.65-72
• /
• 2017

We propose a nearly lossless, compact, electrically modulated vertical directional coupler, which is based on the controllable evanescent coupling in a previously proposed graphene-assisted total internal reflection (GA-FTIR) scheme. In the proposed device, two single-mode waveguides are separate by graphene-$SiO_2$-graphene layers. By changing the chemical potential of the graphene layers with a gate voltage, the coupling strength between the waveguides, and hence the coupling length of the directional coupler, is controlled. Therefore, for a properly chosen, fixed device length, when an input wave is launched into one of the waveguides, the ratio of their output powers can be controlled electrically. The operation of the proposed device is analyzed, with the dispersion relations calculated using a model of a one-dimensional slab waveguide. The supermodes in the coupled waveguide are calculated using the finite-element method to estimate the coupling length, realistic devices are designed, and their performance was confirmed using the finite-difference time-domain method. The designed $3{\mu}m$ by $1{\mu}m$ device achieves an insertion loss of less than 0.11 dB, and a 24-dB extinction ratio between bar and cross states. The proposed low-loss device could enable integrated modulation of a strong optical signal, without thermal buildup.