• Industrial Engineering and Management Systems
• /
• v.12 no.3
• /
• pp.281-287
• /
• 2013

In this paper, we introduce a roots method that uses the roots inside the unit circle of the associated characteristics equation to evaluate the steady-state system-length distribution at three epochs (pre-arrival, arbitrary, and post-departure) and sojourn-time distribution in GI/PH/1 queueing model. It is very important for an air base to inspect airplane oil because low-quality oil leads to drop or breakdown of an airplane. Since airplane oil inspection is composed of several inspection steps, it sometimes causes train congestion and delay of inventory replenishments. We analyzed interarrival time and inspection (service) time of oil supply from the actual data which is given from one of the ROKAF's (Republic of Korea Air Force) bases. We found that interarrival time of oil follows a normal distribution with a small deviation, and the service time follows phase-type distribution, which was first introduced by Neuts to deal with the shortfalls of exponential distributions. Finally, we applied the GI/PH/1 queueing model to the oil train congestion problem and analyzed the distributions of the number of customers (oil trains) in the queue and their mean sojourn-time using the roots method suggested by Chaudhry for the model GI/C-MSP/1.

• Journal of the Korean Ceramic Society
• /
• v.31 no.5
• /
• pp.471-476
• /
• 1994

The influence of TiO2 addition on the sintering and microstructure of magnesia ceramics was studied. An excess amount of TiO2 over the solid solubility limit reacted with magnesia to form Mg2TiO4 compound above 130$0^{\circ}C$. The deviation of lattice parameter of MgO was estimated to be under 0.2% when existence of TiO2 in MgO. The addition of TiO2 markedly promoted the densification of MgO at comparatively low temperature and the sintered density of about 98% of the theorectical was obtained at 150$0^{\circ}C$, 2h. The densification was mainly governed by grain growth of MgO and the effect of Mg2TiO4 existing as a second phase on depression of grain growth of MgO was not exhibited.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.401-412
• /
• 2003

In this paper, a broadband phase shifter structure using a new switched network was proposed. A new reference network is composed of coupled lines and 45$^{\circ}$open and short stubs, which are shunted at the edge points of a main line, respectively, A delay network is composed of only a standard transmission line. It is possible to design a broadband 180$^{\circ}$phase shifter that phase dispersive characteristics by an impedance ratio R of coupled lines and greater phase dispersive characteristics by characteristic impedances Zm, Zs of a main line and stubs are used together. By considering a structure symmetry, the even and odd mode analysis was performed to obtain theoretical S-parameters of the proposed phase shifter. Also, through computer simulation on the basis of derived equations, design graphs were presented to optimally design a 180$^{\circ}$broadband phase shifter. Design graphs provide the values of characteristic impedances Zm, Zs, and I/O match and phase bandwidths. To verify electrical performances of the broadband phase shifter proposed in this paper, low different 180$^{\circ}$phase shifters, operated at the center frequency 3 GHz were designed and fabricated using design graphs, and were experimented. One of them was designed as a standard Schiffman structure to compare with electrical performances. Measured results of each phase shifter to satisfy simultaneously design conditions of I/O match （VSWR=1.15:1) and maximum phase deviation $({\varepsilon}_{{\Delta}{\phi}}＝{\pm}2^{\circ})$ were well in agreement with corresponding simulation results over impedance match and phase error bandwidths, and showed broadband characteristics.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.144-149
• /
• 2014

Large residual stresses are remained in the conventional injection molded products because of the high cavity pressure in packing phase during injection molding process. Conventional injection molding (CIM) invokes distribution of cavity pressure and it has a limitation to obtain product with uniform physical property. Multi-cavity conventional injection molding contains quality deviation among the cavities since flow imbalance occurs during filling phase. Injection compression molding (ICM) is adopted to overcome these limitations of CIM. In this study, molding characteristics of CIM and ICM have been investigated using multi-cavity injection mold. Researches were performed by both experiment and computer simulation through observations of birefringence for transparent resins, polycarbonate and polystyrene in CIM and ICM. As a result, low and uniform birefringence and mold shrinkage were showed in the specimens by ICM that could give a uniform cavity pressure. Deviation of physical property among the specimens in multi-cavity mold shown in CIM was significantly reduced in the specimens by ICM. Through this study it was concluded that the ICM in multi-cavity molding was valid for molding products with uniform property in an individual cavity and also reduced property deviation among the cavities.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.8 no.2
• /
• pp.95-104
• /
• 2012

In this paper, an estimation of person height and 3D location of a moving person by using the pan/tilt-embedded stereo tracking system is suggested and implemented. In the proposed system, face coordinates of a target person is detected from the sequential input stereo image pairs by using the YCbCr color model and phase-type correlation methods and then, using this data as well as the geometric information of the stereo tracking system, distance to the target from the stereo camera and 3-dimensional location information of a target person are extracted. Basing on these extracted data the pan/tilt system embedded in the stereo camera is controlled to adaptively track a moving person and as a result, moving trajectory of a target person can be obtained. From some experiments using 780 frames of the sequential stereo image pairs, it is analyzed that standard deviation of the position displacement of the target in the horizontal and vertical directions after tracking is kept to be very low value of 1.5, 0.42 for 780 frames on average, and error ratio between the measured and computed 3D coordinate values of the target is also kept to be very low value of 0.5% on average. These good experimental results suggest a possibility of implementation of a new stereo target tracking system having a high degree of accuracy and a very fast response time with this proposed algorithm.

• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.127-133
• /
• 2001

In SRM drive, the ON OFF angles of each phase switch should be accurately controlled in order to control the torque and speed stably. The accuracy of the switching angles is dependent upon the resolution of the encoder and the sampling period of the microprocessor, that are used to provide the information of the rotor position and to control the SRM power circuit, respectively. However, as the speed increases, the amount of the switching angle deviation from the preset values is also increased. Therefore, the low cost encoder suitable for the practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using the simple digital logic circuit is also presented in this paper. As a result, a stable high speed SRM drive can be achieved by the high resolution switching angle control and it is verified from the experiments that the proposed encoder and logic controller can be a powerful candidate for the practical low cost SRM drive.

• Journal of Dairy Science and Biotechnology
• /
• v.33 no.1
• /
• pp.27-34
• /
• 2015

The aim of this study was to optimize a simple, fast, and economic analytical method for the simultaneous determination of various pesticides (aldrin, p,p'-DDT, o,p'-DDT, p,p'-DDE, ${\alpha}$-endosulfan, ${\beta}$-endosulfan, dieldrin, heptachlor, permethrin, chlordane, deltamethrin, diazinon, bifenthrin, methoprene, propargite, fenpropathrin, cypermethrin, fenvalerate, and fenpropathrin) in milk by using dispersive solid phase extraction (SPE). In this study, two different extraction methods (low temperature cleanup and liquid-liquid partitioning), which were followed by a cleanup process based on dispersive-SPE, were evaluated and compared for the 19 pesticides. The results for all the pesticides were determined by gas chromatography mass spectrometry (GC/MS) with selected-ion monitoring mode, and the matrix effect of the method was evaluated. Comparison of these approaches yielded higher and more consistent recoveries of most pesticides at fortification levels of $1{\mu}g/mL$ using low-temperature fat precipitation, followed by cleanup process based on dispersive-SPE with PSA and C18 as sorbents, than other preparation process. The relative standard deviation was <20 % and the combination of this method were very effective for the cleanup.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.11
• /
• pp.981-989
• /
• 2005

In this study, external condensation heat transfer coefficients (HTCs) are measured on a low fin tube and Turbo-C tubes at the saturated vapor temperature of $30^{\circ}C$, $39^{\circ}C$, and $50^{\circ}C$ for R22, R410A, R407C and R134a with the wall subcooled at $3{\~}8^{\circ}C$. The HTCs of all refrigerants decreased as increasing the saturation temperature from $30^{\circ}C$ to $50^{\circ}C$. This trend is due to better thermodynamic properties of the liquid phase at low temperature Beatty and Katz's prediction yielded a $20.0\%$ deviation for the low fin tube data. The heat transfer enhancement factors for the 26 fpi low fin tube and Turbo-C tubes are 4.0${\~}$5.5 and 3.0${\~}$8.1 respectively for the refrigerants tested. Finally the performance of Turbo-C tube is better than that of the low fin tube.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.87-90
• /
• 2005

The FORMOSAT-3/COSMIC mission is a micro satellite mission to deploy a constellation of six micro satellites at low Earth orbits. The final mission orbit is of an altitude of 750-800 lan. It is a collaborative Taiwan-USA science experiment. Each satellite consists of three science payloads in which the GPS occultation experiment (GOX) payload will collect the GPS signals for the studies of meteorology, climate, space weather, and geodesy. The GOX onboard FORMOSAT -3 is designed as a GPS receiver with 4 antennas. The fore and aft limb antennas are installed on the front and back sides, respectively, and as well as the two precise orbit determination (POD) antennas. The precise orbit information is needed for both the occultation inversion and geodetic research. However, the instrument associated errors, such as the antenna phase center offset and even the different cable delay due to the geometric configuration of fore- and aft-positions of the POD antennas produce error on the orbit. Thus, the focus of this study is to investigate the impact of POD antenna parameter on the determination of precise satellite orbit. Furthermore, the effect of the accuracy of the determined satellite orbit on the retrieved atmospheric and ionospheric parameters is also examined. The CHAMP data, the FORMOSAT-3 satellite and orbit parameters, the Bernese 5.0 software, and the occultation data processing system are used in this work. The results show that 8 cm error on the POD antenna phase center can result in ~8 cm bias on the determined orbit and subsequently cause 0.2 K deviation on the retrieved atmospheric temperature at altitudes above 10 lan.

• The Journal of Korean Obstetrics and Gynecology
• /
• v.35 no.3
• /
• pp.122-136
• /
• 2022

Objectives: The aim of this study is to investigate Heart Rate Variability (HRV) characteristics of patients with primary dysmenorrhea at the menstrual phase. Methods: 7 databases (Pubmed, Cochrane library, CNKI, RISS, KISS, OASIS, ScienceON) were searched for eligible studies published before 2021 December. The studies comparing HRV between patients with primary dysmenorrhea and controls were included. A random-effects model was used to evaluate differences of HRV parameters between patients with primary dysmenorrhea and controls. Results: 4 articles were included in this review based on inclusion and exclusion criteria. SDNN (Standard deviation of NN intervals), RMSSD (Square root of the mean squared difference of successive NN intervals), mean PR (Mean of pulse rate), LF (Low frequency), HF (High frequency), was the most frequently used as HRV parameters. RMSSD was significantly lower in patients with primary dysmenorrhea than controls. There was no statistically significant difference of other HRV parameters between patients with primary dysmenorrhea and controls. Conclusions: This study suggests that parasympathetic activity and overall functions of autonomic nervous system might be decreased in patients with primary dysmenorrhea at the menstrual phase. In the future, well-designed clinical studies using HRV and additional meta-analysis should be conducted to obtain a wealth of information about HRV characteristics of patients with primary dysmenorrhea.