• 한국정밀공학회지
• /
• 제11권4호
• /
• pp.114-125
• /
• 1994

Fatigue behavior and life prediction method were presented for themal-mechanical and isothermal low cycle fatigue of 12 Cr forged steel used for high temperature applications. In-phase and out-of-phase thermal-mechanical fatigue test from 350 .deg. C to 600 .deg. C and isothermal low cycle fatigue test at 600 .deg. C, 475 .deg. C, 350 .deg. C were conducted using smooth cylindrical hollow specimen under strain-control with total strain ranges from 0.006 to 0.015. The phase difference between temperature and strain in thermal-mechanical fatigue resulted in significantly shorter fatigue life for out-of-phase than for in-phase. Thermal-mechanical fatigue life predication was made by partitioning the strain ranges of the hysteresis loops and the results of isothermal low cycle fatigue tests which were performed under the combination of slow and fast strain rates. Predicted fatigue lives for out-of-phase using the strain range partitioning method showed an excellent agreement with the actual out-of-phase thermal-mechanical fatigue lives within a factor of 1.5. Conventional strain range partitioning method exhibited a poor accuracy in the prediction of in-phase range partitioning method in a conservative way. By the way life prediction of thermal-mechanical fatigue by Taira's equivalent temperature method and spanning fartor method showed good agreement within out-of-phase thermal-mechanical fatigue.

• 대한기계학회논문집A
• /
• 제32권2호
• /
• pp.177-185
• /
• 2008

Low-cycle environmental fatigue tests of cast austenitic stainless steel CF8M at the condition of fatigue strain rate 0.04%/sec were conducted at the pressure and temperature, 15MPa, $315^{\circ}C$ of a operating pressurized water reactor (PWR). The used test rig was limited to install an extensometer at the gauge length of the cylindrical fatigue specimen inside a small autoclave. So the magnet type LVDT#s were used to measure the fatigue displacement at the specimen shoulders inside the high temperature and high pressure water autoclave. However, the displacement and strain measured at the specimen shoulders is different from the one at the gauge length for the geometry and the cyclic strain hardening effect. Displacement of the fatigue specimen gauge length calculated by FEM (finite element method) used to modify the measured displacement and fatigue life at the shoulders. A series of low cycle fatigue life tests in air and PWR conditions simulating the cyclic strain hardening effect verified that the FEM modified fatigue life was well agreed with the simulating test results. The process and method developed in this study for the environmental fatigue test inside the small sized autoclave would be so useful to produce reliable environmental fatigue curves of CF8M stainless steel in pressurized water reactors.

• 대한기계학회논문집A
• /
• 제40권12호
• /
• pp.1027-1035
• /
• 2016

내식성과 기계적 성능이 우수한 316L 스테인리스 강의 저주기 변형률제어 피로시험에서 3가지 변형률진폭과 3가지 변형률비의 조건이 피로수명에 미치는 효과를 분석하였다. 낮은 변형률범위에서 곡선이 거의 중첩되는 Masing 거동이 나타나고, 높은 변형률범위에서 비선형거동 응력범위가 서로 크게 벗어나는 non-Masing 거동과 함께 평균응력의 감소가 나타났다. 소성 변형률에너지를 이용하여 저주기 피로수명을 예측하고 non-Masing 거동을 고려한 수명예측 방법의 정확성 여부를 검토하였다. 각각의 변형률진폭과 변형률비의 조건에서 초기 수 사이클 동안 반복경화 현상 후 장시간동안 점진적으로 낮아져 연화하다가 파괴 되었다. 저사이클 피로수명을 정확히 예측하기 위해서는 변형률진폭에 따라 Masing 및 non-Masing 거동을 구분하고, 이를 반영한 수명예측식을 적용해야 함을 알았다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.7-12
• /
• 2000

The automatic turbine startup system provides turbine control based on thermal stress. During the startup, control system monitors and evaluates main components of turbine using damage mechanism and life assessment. In case of valve chest, the temperature of inner/outer wall is measured by thermo-couples and the safety of these values are evaluated by using allowable ${\Delta}T$ limit curve during the startup. Because allowable ${\Delta}T$ limit curve includes life assessment, it is possible to apply this curve to turbine control system. In this paper, low cycle fatigue damage and combined rupture and low cycle fatigue damage criterion proposed for yielding the allowable ${\Delta}T$ limit curve of CV(control valve) chest. To calculate low cycle fatigue damage, the stress analysis of valve chest has peformed using FEM. Automatic turbine startup to assure service life of CV was achieved using allowable ${\Delta}T$ limit curve.

• 대한기계학회논문집A
• /
• 제26권1호
• /
• pp.1-6
• /
• 2002

The automatic turbine startup system provides turbine control based on thermal stress. During the startup, control system monitors and evaluates main components of turbine using damage mechanism and life assessment. In case of valve chest, the temperature of inner/outer wall is measured by thermo-couples and the safety of these values are evaluated by using allowable △T limit currie during the startup. Because allowable ΔT limit curve includes life assessment, it is possible to apply this curve to turbine control system. In this paper, low cycle fatigue damage, combined rupture and low cycle fatigue damage criterion were proposed for yielding the allowable ΔTf limit curve of CV(control valve) chest. To calculate low cycle fatigue damage, the stress analysis of valve chest has been performed using FEM. Automatic turbine startup to assure service life of CV was achieved using allowable ΔT limit curve.

• 대한기계학회논문집A
• /
• 제34권10호
• /
• pp.1419-1425
• /
• 2010

열간성형된 보론강판은 고강도특성이 필요한 자동차 부품에 널리 적용되고 있으며, 최근에는 샤시 부품에도 점차로 적용되고 있다. 샤시 부품으로 적용되기 위해서 고강도 특성뿐만 아니라 내피로특성이 동시에 요구되고 있어, 본 연구에서 열간성형된 보론강판의 저주기 피로특성을 연구하였다. 저주기 피로시험결과, 총변형률 진폭이 낮은 영역에서는 열간성형된 보론강의 피로수명이 현저히 높았지만, 높은 총변형률 진폭에서는 열간성형된 보론강의 마르텐사이트 조직특성인 낮은 연성과 파괴인성으로 인해서 보론강 원소재의 피로수명이 더 높음을 확인할 수 있었다.

• Nuclear Engineering and Technology
• /
• 제55권2호
• /
• pp.546-554
• /
• 2023

The cyclical behavior of Alloy 617 was examined at 25 ℃ and high temperatures of 800, 850, 900, and 950 ℃ in air to obtain its fatigue life curves. The specimens tested at 25, 800, and 850 ℃ cyclically hardened, whereas those tested above 900 ℃ cyclically softened from the first cycle, that is, their fatigue life was reduced at high temperatures owing to loss of strength. Parameters of the typical Coffin-Manson-Basquin relationship were determined for each test temperature. Interestingly, no significant difference in fatigue life was observed for the specimens tested in the range of 800-950 ℃. Owing to the similarity in fatigue life, we determined fatigue strength and fatigue ductility exponents that could be applied for this temperature range. The parameters obtained were close to the universal slopes, although the fatigue ductility exponent was slightly different. The proposed fatigue life curves were compared with those presented in ASME code.

• 대한기계학회논문집
• /
• 제13권2호
• /
• pp.307-315
• /
• 1989

본 연구에서는 단조과정을 거친후 노멀라이징(normalizing) 처리된 SF45A강종과 압연후 자연 냉각시킨 SM41B강종의 두 국산 강종에 대해 저사이클 피로시험을 행하여 저사이클 피로특성을 밝히고, 강재의 가공공정과 부하변형율변화에 따른 피로과정중의 연화 및 경화 거동을 관찰하였다. 그리고 저사이클 피로파면의 미시적 고찰을 통해서 부하변형율 크기에 따른 미시적 파면 양상의 변화를 밝혀 파괴 해석의 기초자료로 제공하였다.

• 대한기계학회논문집A
• /
• 제40권7호
• /
• pp.653-658
• /
• 2016

가스터빈엔진의 고온 부품은 초내열 합금 재료를 이용하며, 냉각설계 적용으로 형상이 복잡하여 정밀 주조 과정을 거치게 된다. 터빈 부품에 주로 적용이 되는 일방향 응고 및 단결정 재료는 제조 과정에서 결정립 성장 방향이 설계와 다르게 섭동을 가지게 되며, 이는 각 방향에 대한 재료 상수의 섭동을 유발하여 응력 분포의 변화와 함께 피로 수명에 큰 산포를 야기하게 된다. 본 연구에서는 일방향 응고 재료 노즐에 대하여 결정립 성장 방향의 섭동에 대한 구조 건전성의 영향을 저주기 피로 수명을 통해 확인하여, 향후 제작 허용값에 대한 제안 및 좀 더 정교한 통계적 접근이 필요함을 확인하고자 한다. 이를 위해 복합 열전달 해석을 통해 금속 온도 분포를 계산하고 이를 근거로 구조 해석 및 저주기 피로 수명을 계산하였다.

• 한국압력기기공학회 논문집
• /
• 제6권1호
• /
• pp.50-56
• /
• 2010

Fatigue has been known as a major degradation mechanism of ASME class 1 components in nuclear power plants. Fatigue damage could be accelerated by combined interaction of several loads and environmental factors. However, the environmental effect is not explicitly addressed in the ASME S-N curve which is based on air at room temperature. Therefore many studies have been performed to understand the environmental effects on fatigue behavior of materials used in nuclear power plants. As a part of efforts, we performed low cycle fatigue tests under various environmental conditions and analyzed the environmental effects on the fatigue life of SA508 Gr. 1a low alloy steel by comparing with higuchi's model. Test results show that the fatigue life depends on water temperature, dissolved oxygen and strain rate. But strain rate over 0.4%/s has little effect on the fatigue life. To find the cause of different fatigue life with ANL's and higuchi's model, another test performed with different heat numbered and heat treated materials of SA508 Gr. 1a. On a metallurgical point of view, the material with bainite microstructure shows much longer fatigue life than that with ferrite/pearlite microstructure. And the characteristics of crack propagation as different microstructure seem to be the main cause of different fatigue life.