• Transactions on Electrical and Electronic Materials
• /
• v.9 no.6
• /
• pp.265-272
• /
• 2008

In this paper, AC losses of long wire Bi-2223 tapes with different twist pitch of superconducting core were fabricated, measured and analyzed. These samples produced by a powder-in-tube method are multi-filamentary tape with Ag matrix. Also, it's produced by non-twist. The critical current measurement was carried out under the environment in Liquid nitrogen and in zero field by 4-prob method. And the Magnetic measurement was carried out under the environment of applied time-varying transport current by transport method. From experiment, the susceptibility measurements were conducted while cooling in a magnetic field. Flux loss measurements were conducted as a function of ramping rate, frequency and field direction. The AC flux loss increases as the twist-pitch of the tapes decreased, in agreement with the Norris Equation. Neutron-diffraction measurements have been carried out investigate the crystal structure, magnetic structures, and magnetic phase transitions in Bi-2223([Bi, Pb]:Sr:Ca:Cu:O).

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.411-412
• /
• 2002

Piston-cylinder system are widely used in power engineering applications. In reciprocating refrigeration compressors, where extremely low friction losses are required, ringless pistons are being used to diminish the friction between piston rings and cylinder wall. Since the ringless piston has the freedom of lateral motion there is a potential danger that it will occasionally hit the cylinder wall while moving up and down along it's axis. A good design must therefore provide a smooth and stable reciprocating motion of the piston and ensure that the fluid film separating the piston from the cylinder wall is maintained all times. And the compromise between refrigerant gas leakage through the piston-cylinder clearance and the friction losses is required utilizing a dynamic analysis of the secondary motion for the high efficiency compressor. To this end, the computer program is developed for calculating the entire piston trajectory and the lubrication characteristics as functions of crank angle under compressor running conditions. The results explored the effects of some design parameters and operating conditions on the stability of the piston, the oil leakage, and friction losses.

• Journal of the Korean Society of Combustion
• /
• v.19 no.4
• /
• pp.21-27
• /
• 2014

MGT (micro gas turbines) have been gaining particular attentions with a variety of commercial and military applications due to their advantages such as compact size, simple operability, easy maintenance, and low emissions. This study deals with development processes of an annular combustor applied to MGT. Preliminary design methodologies are used to size the main components of the combustor. Key design features such as liner temperatures and pressure losses are evaluated. Results show that the estimated liner temperatures are within acceptable range. Dominant factors for pressure losses are estimated to be air admission holes and burner swirlers.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.6
• /
• pp.1582-1589
• /
• 2016

In this paper the integration of Distributed Generation (DG) in radial distribution system is investigated by computing the optimal site and size of DG to be placed. An analytical expression based on equivalent current injection has been derived by utilizing topological structure of radial distribution system to find optimal size of DG to minimize losses. In the presented formulation, the optimal DG placement is obtained without repeatedly computing the load flow. The proposed formulation can be used to find the optimal size of all types of DGs namely Type-I, Type-II, Type-III and Type-IV DGs. The investigations are carried out on IEEE 33-bus and 69-bus radial distribution systems. The optimal DG placement results into reduction in active and reactive power losses and improvement in voltage profile of the buses.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.173-181
• /
• 2017

In this paper, the bifurcation criteria for inductive power transfer (IPT) systems is suggested considering the inductive power pad losses. The bifurcation criteria for series-series (SS) and series-parallel (SP) topologies are derived in terms of the main parameters of the IPT system. For deriving precise criteria, power pad resistance is obtained by copper loss calculation and core loss analysis. Utilizing the suggested criteria, possibility of bifurcation occurrence can be predicted in the design process. In order to verify the proposed criteria, 50 W IPT laboratory prototype is fabricated and the feasibilities of the switching frequency and AC load resistance shift to escape from bifurcation are identified.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.397-398
• /
• 2016

This paper analyzes switching losses, efficiency and temperature depending on Si and SiC devices applied in two stage AC-DC converter. To evaluate the charge and discharge performance and stability of the battery pack, there is a need for a battery pack testing system. To do battery charge and discharge experiment used in battery pack test, A topology, two stage AC-DC converter, has been built. SiC devices more decrease switching losses than that of Si. Also, cooling system was applied in Si and SiC devices. When using SiC devices, it can be confirmed that the size of heat sink is reduced for small loss.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.55 no.3
• /
• pp.133-140
• /
• 2006

This paper is proposed an efficiency optimization control algorithm for a synchronous reluctance motor(SynRM) which minimizes the copper and iron losses. Also, this paper presents a speed estimated control scheme of SynRM using artificial neural network(ANN). There exists a variety of combinations of d and q-axis current which provide a specific motor torque. The objective of the efficiency optimization controller is to seek a combination of d and q-axis current components, which provides minimum losses at a certain operating point in steady state. It is shown that the current components which directly govern the torque production have been very well regulated by the efficiency optimization control scheme. The proposed algorithm allows the electromagnetic losses in variable speed and torque drives to be reduced while keeping good torque control dynamics. The control performance of ANN is evaluated by analysis for various operating conditions. Analysis results are presented to show the validity of the proposed algorithm.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.31-35
• /
• 2001

IGCTs have established themselves as the power semiconductor of choice at medium voltage levels within the last few years because of their low conduction and switching losses. The trade-off between these losses can be adjusted by various lifetime control techniques and the growing demand for these devices is driving the need for standard types to cover such applications as Static Circuit Breakers (low on-state) and Medium Voltage Drives (low switching losses). The additional demands of Traction (low operating temperatures) and Current Source Inverters (symmetric blocking) would normally result in conflicting demands on the semiconductor. This paper will outline how a range of power devices can meet these needs with a limited number of wafers and gate units. Some of the key differences between IGCTs and IGBTs will be explained and the outlook for device improvements will be discussed.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.4
• /
• pp.363-370
• /
• 2000

Experiments have been peformed, using pure refrigerant R134a and a zeotropic refrigerant mixture R290/R600a(60%/40%) and their performances have been analyzed by the first and second laws(exergy method) of thermodynamics. From the experimental results, variations of compressor speed and air temperature have a great effect on the performance of the system. The sum of exergy losses in compressor and evaporator is about 60% of total exergy loss, using refrigerant R134a, so it is necessary to improve the performance of compressor and evaporator. According to the experimental results using refrigerant mixture of R290/R600a(60%/40%), the exergy losses in heat exchange processes are decreased but the exergy loss in throttling process is increased. The performance of the system has been improved by 20∼30% compared with that of R134a and exergy losses have been also reduced.

• Progress in Superconductivity and Cryogenics
• /
• v.5 no.1
• /
• pp.97-101
• /
• 2003

When HTS tapes are used in power application, they are used by winding form, such as, a pancake and a solenoid. When AC current is applied to the coil, Ac magnetic field is generated in winding. This AC magnetic field acts as an external magnetic field and makes loss. In this paper the radial magnetic field component ($B_r$) and the axial magnetic field component ($B_z$) in a pancake and a solenoid were calculated by numerical analysis method and compare with measured value. AC losses of a short sample were calculated by Norris equation and n numerical analysis based on Brandt equation. AC losses of the pancake coil and the solenoid coil were also calculated.