• 열처리공학회지
• /
• 제23권6호
• /
• pp.301-308
• /
• 2010

A steel with chemical composition, 0.22% C, 0.25% Si, 1.26% Mn, 0.22% Cr, 0.04% Ti, 0.0042% B, and a microstructure of ferrite and spheroidized cementite has been press-formed to automotive center pillar followed by local-hardening heat-treatment. Hardness, tensile properties, fractography, microstructure and surface roughness of local-hardening heat-treated automotive center pillar have been examined. The directly heated and quenched area had fully martensitic structure with Vickers hardenss in the range of 500 to 510. The heat affected area close to the directly heated area showed dual-phase structure of ferrite and martensite. The width of the heat-treated and heat-affected areas after the local-hardening heat treatment was ranging from 32 mm to 50 mm. The surface of the local-hardening heat-treated center pillar revealed some temper color as a consequence of the oxidation during the heat treatment, but the surface roughness was not affected by the local-hardening heat treatment.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권8호
• /
• pp.1048-1054
• /
• 2011

레이저 표면경화처리는 고밀도 에너지 열원에 의해 레이저 조사부위만 급속 가열한 후 표면의 열이 내부로 전도되어 급속히 자기냉각 됨으로써 표면을 경화시키는 방법이다. 이 표면처리 방법은 열처리에 의한 열변형이 거의 없고, 표면경화처리 이후 다른 공정을 수반하지 않는다. 또한 국부적인 가공이 가능하기 때문에 복잡한 형상을 가지는 금형에는 적합한 표면처리 방법이다. 본 연구에서는 열처리에 적합한 빔 프로파일을 가진 고출력 다이오드 레이저를 이용하여 금형재료용 주철의 표면처리를 실시하였다. 프레스 금형 공정에 따른 금형의 형상이 다르기 때문에 적용부위에 따라 시험편을 평면과 모서리부로 나누어 열처리를 실시하였다. 이때 모서리부의 열처리는 광학헤드를 $10^{\circ}$ 기울인 상태에서 진행하였다. 그 결과, 모서리부의 열처리는 평면부와 비교하여 형상에 따른 열전달 루트가 제한되므로, 입열이 집중되기 쉬워 평면 열처리보다 빠른 이송속도에서 경화가 이루어졌다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.292-292
• /
• 2000

Since high-power CO$_2$ Laser can be make a high densed energy to Local processing area, manufacturing processes using the laser can be processed for very Localized areas at a very fast rate with minimal or no distortion. Accordingly, the laser has been widely used in the fields of thermal manufacturing processes such as welding, fusion cutting, grooving, and heat treatment of metals. In particular, interest in the laser heat treatment process has grown tremendously in the past few years. In this process, maintaining the uniform hardening depth is important problem to obtain good quality products and to reduce heat induced distortion and residual stress. For achieving this objective, we introduced a new design technique of a fuzzy logic controller that greatly simplified the design procedure by defining several simplified design parameters. In the design procedure, the major design parameters of the controller are characterized by identifying several common aspects. From a series of simulation results, we found that the proposed design technique can be effectively used to design of a fuzzy logic controller for the LASER surface hardening process.

• 열처리공학회지
• /
• 제24권4호
• /
• pp.203-208
• /
• 2011

Recently, from general machine parts and automobile parts using carbon steel to a mold, there has been efforts for improving durability and attrition resistance of these parts. Especially, heat treatment with laser which works fast and automatically can be used for the mass production with high quality. Moreover, local heat treatment can be used to handle with complex and precise parts. Accordingly, we analyzed hardening characteristics of carbon steel using the finite element method and compare the experimental results to have more reliability. We also proved the cause of thermal deformation with temperature and stress distribution by heat treatment. After these analysis and experimental, we found that each maximum hardness of the two tests was 728 Hv and 700 Hv, on condition of $1050^{\circ}C$ heating temperature, and 2 mm/sec laser speed. We also found that difference of surface stress-distribution was occurred, and this makes deformation mode up after heat treatment.

• 한국철도학회논문집
• /
• 제7권2호
• /
• pp.142-148
• /
• 2004

When material properties depend much on positions in a material or it is difficult to make test specimens from a material or component, an instrumented indentation test described in ISO 14577-1, 14577-2 or KS B 0950 can be used to measure material properties and damage. In this study, first of all, the principals of the instrumented indentation test, KS B 0950 are introduced and yield strengths, tensile strengths and work hardening exponents of base materials, heat affected zones and weld materials are measured. In addition, the influence of post-weld heat treatment on the material properties is investigated. Finally the fatigue lift of butt welded specimens are evaluated by the local strain approach. To calculate local strains and stresses, elasto-plastic finite element analysis is conducted using the measured properties.

• 한국산학기술학회논문지
• /
• 제15권9호
• /
• pp.5460-5466
• /
• 2014

본 연구에서는 실생활에 많이 이용되며 주로 주방용 식기 및 식칼, 소형칼, 주방 가위 등으로 널리 사용되는 STS420J2를 실험소재로 사용하였다. 마르텐사이트계 스테인리스강은 Cr13%이상 함유하고 있어 약 $1,050^{\circ}C$를 정점으로 하여 그 이상의 고온에서는 저하하는 단점을 가지고 있다. 실험에 사용되는 시험편 표면에 표면경화를 수행하기 위하여 #200 ~ #1500의 순서대로 미세연마 후 거친연마 가공을 실시하였으며, 다이오드 레이저의 표면경화 열처리 후에 자기냉각효과를 고려하여 $100{\times}50{\times}10$의 판재로 시험편을 제작하여 실험하였다. 소재 표면에 다이오드 레이저를 이용하여 국소부위에 표면경화 열처리를 수행하였다. 이때 다이오드 레이저의 출력과 이송속도를 공정조건으로 하여, 미세경도시험, 미세조직시험, 전자 주사 현미경(SEM), 입열량을 분석하였다. 분석 후에는 실험소재의 기계적 특성을 비교하여, 타 표면경화법에 비해 다이오드 레이저를 이용하였을 때의 표면경화 열처리 신뢰성과 우수함 그리고 최적의 공정조건을 도출하였다. 열처리 후 경화부는 Plate martensite로 경화 되었으며. 경도값은 Hv606.2로 열처리 후 약 3배 이상 표면경도가 향상되었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1542-1547
• /
• 2007

Laser surface treatment technologies have been used to improve characteristics of wear and to enhance the fatigue resistance for mold parts. The optical lens with the elliptical profile is designed to obtain a wide surface hardening area with a uniform hardness. The objective of this research work is to investigate the influence of the process parameters, such as power of laser and defocused spot position, on the characteristics of laser surface treatment for the case of SKD61 steel and SCM4 steel. From the results of the experiments, it has been shown that the maximum average hardness is approximatly 700${\sim}$780 Hv when the power, focal position and the travel of laser are 1,095 W, 0mm and 0.3 m/min, respectively. In samples treated with lower scanning speeds, some small carbide particles appear in the interdendritic regions. This region contains fine martensite and carbide in proportions which depend on the local thermal cycle.

• Journal of Welding and Joining
• /
• 제2권1호
• /
• pp.4-17
• /
• 1984

Overlaid weld metals of austenitic stainless steel in a pressure vessel of power reactor are usually post-weld heated for a long period of time after welding. The PWHT is considered as a kind of sensitizing and it is important to check the soundness of the weld metal after PWHT, especially about the precipitation of carbides. The purpose of this report is to obtain information on the relation between the change of microstructure and Post-Weld Heat Treatment in the overlaid weld metals. Metallurgical aspects of the problem on austenitic stainless steel heated at $625^{\circ}C$, $670^{\circ}C$, $720^{\circ}C$ and $760^{\circ}C$ for 3, 10, 30, 100 and 300 hours have been investigated by means of optical-micrography, micro-hardness measurement, scanning electron microscope and electron-probe micro analysis. From the results obtained, the following conclusions are drawn; 1) The PWHT above $625^{\circ}C$ for a long time causes a diffusion of carbon atoms from low alloy steel into stainless steel, and consequently carbon is highly concentrated at the boundary layer of stainless steel. 2) C in ferritic steel migrated to austenitic steel and carbides precipitated in austenitic steel along fusion line. At higher temperatures, the ferrite grains coarsened in the decarburized zone. 3) In the change of microstructure of stainless steel overlaid weld metal, the width of carbides precipitated zone and decarburized zone increased with increase of PWHT temperature and time. 4) At about $625^{\circ}C$ to $760^{\circ}C$, chromium carbides, mainly $M_{23} C_6$, precipitate very closely in the carburized layer with remarkable hardening. 5) Precipitation of delta ferrite from molten weld metal depends on solidification phenomenon. There was a small of ferrite near the bond in which the local solidification time was short, comparing with after parts of weld metal. Shape and amount of ferrite were not changed by Post-Weld Heat Treatment after solidification.

• 한국분말재료학회지
• /
• 제14권1호
• /
• pp.13-18
• /
• 2007

The mother Ni-W (1-5 wt.%) alloy billets for coated conductor substrate were fabricated by powder metallurgy process. The tensile test results for the sintered Ni-W rods showed the increase of mechanical strength and decrease of ductility with increasing W content due to the solid solution hardening. All the fracture surfaces of the tested specimens showed the typical ductile fracture mode of dimple rupture due to the local necking. The Ni-W alloy billets were made into tape by cold rolling. After the appropriate heat treatment for recrystallization, the brass texture formed by the cold rolling was converted to the complete cube texture. The in-plane and out of plane texture of the tapes estimated by x-ray pole figure were smaller than 9 degree and 7 degree, respectively. The effect of the W addition on the texture development seems not to be significant.