• 콘크리트학회논문집
• /
• 제13권3호
• /
• pp.244-250
• /
• 2001

지진하중이 작용할 때, 철근콘크리트 구조물에서 취성파괴의 원인은 철근과 콘크리트사이의 과도한 부착손실에 기인한다. 본 연구에서는 반복하중 작용시에 철근의 마디형태에 따른 부착성능의 영향을 평가하고자 하였다. 철근의 마디높이에 변화를 주어 상대마디면적에 변화를 주었고, 횡구속철근양에 변화를 주었다. 단조가력시 횡구속이 증가할수록 부착력도 증가하며 상대마디면적의 증가에 따라서도 약간의 강도변화가 발생하였다. 단조가력시에 비해서 반복가력시에 상대마디면적이 증가할수록 부착력 증가가 더욱 커지는 것으로 관찰되었다. 반복가력시 상대마디면적의 증가에 따른 부착강도의 증가가 횡구속 철근이 있을 때 더욱 뚜렷하게 나타났다. 반복가력시 일정한 슬립에서 반복횟수가 증가할수록 강성은 떨어졌으나, 상대마디면적 증가에 따라 부착슬립량의 감소도 크게 발생했다. 따라서 지진과 같은 반복가력시 상대마디면적이 큰 철근을 사용함으로서 더 작은 슬립으로 더 큰 부착강도를 발휘하게 되어 구조물의 내진성능을 개선시킬 수 있겠다.

• 한국공작기계학회논문집
• /
• 제14권3호
• /
• pp.74-80
• /
• 2005

Steel plates used for common structures are manufactured by rolling processes in general. The rolling direction traces generated during the processes have significant influences on mechanical properties and fatigue behavior of the plates. The objective of present study is to investigate those directional characteristics for the enhancement of steel structure safety. SS400 steel plates of 3 mm thickness are tested in this study, When the angles between the tensile loading direction and the rolling direction of the plates are increased, their yield strengths are increased and elongations are rather decreased. It is also shown that fatigue crack growth rates in the plates can be increased according to the changes of those mechanical characteristics. For the safety of the structures, therefore, it is critical to decrease the angles between the rolling direction and the tensile loading direction.

• 한국운동역학회지
• /
• 제14권2호
• /
• pp.105-119
• /
• 2004

To enhance our understanding of the loads on the foot during treadmill running, we have used a pressure-sensitive insole system to determine pressure, rate of loading and impulse distributions on the plantar surface during treadmill running, both in minimally cushioned footwear and in cushioned shoes. This report includes pressure, rate of loading, impulse and contact time data from a study of ten subjects running on a treadmill at 4.0m/s. Among heel-toe runners, the highest peak pressures and highest rates of loading were observed under the centre of the heel and in the medial forefoot. The arch regions were only lightly loaded. Contact time was greater in the forefoot than in the heel. Two-thirds of the impulse recorded during the step was the result of forces applied through the forefoot, mostly in the region of the metatarsal heads. The distribution of loads in the shoe suggests that the load distributing properties of the cushioning system are most important in the centre of the heel, under the metatarsal heads and great toe. Shock attenuation is primarily required under the centre of the heel and to lesser extent under the metatarsal heads. Some energy dissipation may be desirable in the heel region because it causes shock to be absorbed with less force. All the 'propulsive' effort is applied through the forefoot. Therefore, this region should as resilient as possible.

• Structural Engineering and Mechanics
• /
• 제65권3호
• /
• pp.349-357
• /
• 2018

An extensive research was undertaken to study the vibration serviceability of a long-span and light-weight floor subjected to human loading experimentally and numerically. Specifically, heel-drop test was first conducted to capture the floor's natural frequencies and damping ratios, followed by jumping and running tests to obtain the acceleration responses. In addition, numerical simulations considering walking excitation were performed to further evaluate the vibration performance of a multi-panel floor under different loading cases and walking rates. The floor is found to have a high frequency (11.67 Hz) and a low damping ratio (2.32%). The comparison of the test results with the published data from the 1997 AISC Design Guide 11 indicates that the floor exhibits satisfactory vibration perceptibility overall. The study results show that the peak acceleration is affected by the walking path, walking rate, and adjacent structure. A simpler loading case may be considered in design in place of a more complex one.

• 한국세라믹학회지
• /
• 제51권2호
• /
• pp.97-102
• /
• 2014

In order to improve the refresh rate of old newspaper(ONP), PCC shape-controlling experiments were carried out. The effect of a PCC polymorph on improving the quality of old newspaper was studied for a transformation from waste paper to eco-friendly paper. The synthesis of PCC consists of an in-situ process and a loading process to enhance the refresh rate of old newspaper. The characteristics between the in-situ process and the loading process could be analysed by SEM analyses of coated fiber surfaces. The retention rate ranges from 65 to 67% after the application of the in-situ process, and that after the loading process ranges from 55 to 58%. The retention rates thus show a difference of about 7-10%. In addition, the whiteness and ERIC characteristics of the in-situ process gave more efficient results than those of the loading process.

• Computers and Concrete
• /
• 제33권5호
• /
• pp.519-533
• /
• 2024

Many materials including cementitious concrete-type materials undergo material property changes during high-rate loading. There is a wealth of research regarding this phenomenon for concrete in compression and tension. However, there is minimal knowledge about how mortar material used in concrete masonry unit (CMU) construction behaves in high-rate shear loading. A series of experiments was conducted to examine the bond strength of mortar bonded to CMU units under high-rate shear loading. A novel experimental setup using a shock tube and dynamic ram were used to load specially constructed shear triplets in a double lap shear configuration with no pre-compression. The Finite Element Method was leveraged in conjunction with data from the experimental investigation to establish if the shear bond between concrete masonry units and mortar exhibits any rate dependency. An increase in shear bond strength was observed when loaded at a high strain rate. This data indicates that the CMU-mortar bond exhibits a rate dependent strength change and illustrates the need for further study of the CMU-mortar interface characteristics at high strain rates.

• ALGAE
• /
• 제26권3호
• /
• pp.253-263
• /
• 2011

Phenotypic plasticity was examined in the economically and ecologically important brown alga Ascophyllum nodosum in southwestern Nova Scotia, considering specifically how nutrient loading affected its vegetative and reproductive features. To determine this, we examined morphometric changes in A. nodosum from two sites receiving direct effluent impacts from a land-based finfish aquaculture facility and from two control sites, approximately 2 km away from the aquaculture facility in opposite directions. Fronds from test sites were significantly younger than from control sites (5 y vs. 8 y); however, fronds from farm sites were significantly larger (219 g vs. 90 g) because of their higher growth rates. Thalli from farm sites had greater reproductive potential, as shown by numbers of receptacle initials (797 initials vs. 281 initials). These results suggest limited nutrient inflows from land-based aquaculture may positively affect adjacent Ascophyllum populations by inducing higher growth rates. We conclude that the coordination of effluent management from land-based aquaculture with natural resource harvesting of A. nodosum may be beneficial. Further study is necessary to determine the limits of nutrient loading for this potentially beneficial outcome.

• Computers and Concrete
• /
• 제21권2호
• /
• pp.209-217
• /
• 2018

The dynamic compressive behavior of concrete after freezing and thawing tests are investigated by using the split Hopkinson pressure bar (SHPB) technique. The stress-strain curves of concrete under dynamic loading are measured and analyzed. The setting numbers of freeze-thaw cycles are 0, 25, 50, and 75 cycles. Test results show that the dynamic strength decreases and peak strain increases with the increasing of freeze-thaw cycles. Based on the Weibull distribution model, statistical damage constitutive model for dynamic stress-strain response of concrete after freeze-thaw cycles was proposed. At last, the fragmentation test of concrete subjected to dynamic loading and freeze-thaw cycles is carried out using sieving statistics. The distributions of the fragment sizes are analyzed based on fractal theory. The fractal dimensions of concrete increase with the increasing of both freeze-thaw cycle and strain rate. The relations among the fractal dimension, strain rates and freeze-thawing cycles are developed.

• 한국생산제조학회지
• /
• 제6권4호
• /
• pp.80-88
• /
• 1997

An experimental investigation of the fatigue through crack growth behavior under simple stepped variable loading condition has been performed using Al7075-T651. Experiments were carried out by using cantilever bending type specimens, with chevron notches on a small electro-magnetic test machine. Tensile overloads have a retarding effect on the fatigue crack growth rates, therefore tensile overloads were used for the beneficial effect on the fatigue life. While in most cases compressive overloads have only a vanishing effect on crack growth rates, some experiments with single edge crack tension specimens reveal a marked growth retardation. The stress ratios used in this investigations varies from R=0.32 to 0.81, from R=0.04 to 0.76, from R=-0.15 to 0.73, and from R=-0.33 to 0.68 and the peak load for each case was not varied. The crack growth and crack closure were measured by Kikukawa's compliance method with a strain gauge mounted on the backside of each specimens. The results obtained are as follows. When the stepped variable load was applied, the smaller the stress ration was, the larger the delayed retardation of the crack growth rate was. The fatigue crack growh rate data obtained for through cracks were plotted well against the effective stress intensity factor range from 4.0 to 20.0MP{a^{SQRT}m}. It was found that the effective stress intensity factor range ratio was related well to the opening stress intensity factor, the maximum stress intensity factor, and crack length.

• Environmental Engineering Research
• /
• 제12권2호
• /
• pp.81-91
• /
• 2007

A membrane bioreactor (MBR) was used to investigate the aerobic degradation of foam active substance - non-ionic surfactant, APG 2000 UP. The surface aeration using the propeller loop reactor (PLR) guaranteed sufficient $O_2$ for substrate removal and bacteria growth and avoided foam development. Moreover, the cross-flow membrane filtration enabled the separation of the bacteria still loaded with surfactant in the collecting container. The biological degradation of the surfactant with varying hydraulic retention time (HRT) and influent concentration $c_{S0}$ showed high substrate removal of nearly 95% at high volumetric loading rates up to $7.4\;kgCOD\;m^{-3}d^{-1}$ and at sludge loading rates up to 1.8 kgCOD $(kgVSS\;d)^{-1}$ for biomass concentration $c_B\;{\approx}\;constant $. The increasing $c_B$ from 3.4 to $14.5\;gL^{-1}$ TSS respectively sludge retention time (SRT) from 5.1 to 442 d under complete biomass retention by the membrane filtration resulted in high removal of substrate ${\alpha}\;>\;90%$ with reducing excess sludge production.