• 한국강구조학회 논문집
• /
• 제22권4호
• /
• pp.293-303
• /
• 2010

본 연구는 강구조 설계기준(KBC 2009)에서 골조 안정성 평가를 위해 제시한 하중증폭계수를 적용한 직접해석법의 적용 방법에 따른 영향을 해석적 방법을 통해 평가하는데 목적이 있다. 이를 위해 KBC 2009에서 제안하고 있는 가상수평하중 적용 방법, 휨강성 감소 방법, B2 계수 산정 방법 등을 각각 적용한 직접해석을 3층 1스팬 및 5층 3스팬 비가새 강구조 골조에 대해 실시하고, 그 해석 결과를 2차 비탄성 해석 결과와 비교하여 각 적용 방법의 영향을 평가하였다. 직접해석법 적용 방법 이외에 외적 요인의 영향을 고찰하기 위해 골조의 규모, 기둥의 축력비, 축력의 층별분포 등도 변수로 추가하였다. 연구 결과 소요압축강도는 직접해석법 적용 방법에 따른 차이가 크지 않은 것으로 나타났으며, 소요휨강도는 가상수평하중 누계 및 추가 적용, 층강성 개념 B2 계수를 직접해석법에 적용시 적절한 결과를 나타내었다.

• 한국지반환경공학회 논문집
• /
• 제12권10호
• /
• pp.83-90
• /
• 2011

본 연구에서는 고성토 구간 파형강판 수로암거의 대표단면을 대상으로 뒤채움부의 다짐도에 따른 원형 연성지중 암거에 작용되는 수직토압 분포를 파악하기 위해 원심모형실험을 실시하였다. 모형실험은 뒤채움부의 다짐도를 80, 85, 90, 95%로 변화시키면서 현장의 상사성을 고려하여 53g-level의 중력수준에서 수행하였다. 실험결과, 연성거동을 하는 파형강판 상부의 아칭효과에 의한 하중감소계수는 AISI(2002) 설계법에서 규정한 뒤채움 다짐도에 따른 하중감소계수와 거의 일치하였다. 파형강판 상부에서 측정된 수직토압은 다짐도가 증가함에 따라 선형적으로 감소하였으며, 뒤채움부의 다짐도가 클수록 아칭효과에 의한 파형강판 상부의 상재하중 감소가 크게 발휘된다는 것을 확인할 수 있었다. 파형강판 상부에서 발생한 아칭효과에 의해 감소한 하중이 파형강판측면 뒤채움부(EP 1)와 뒤채움부 외부(EP 3)로 전이되는 것으로 나타났다.

• Journal of Electrical Engineering and Technology
• /
• 제5권3호
• /
• pp.468-476
• /
• 2010

This paper presents a direct single-stage power converter using single-phase isolated full-bridge converter modules, with inherent power factor correction (PFC) for a 12 kW switched mode power supply (SMPS). The advantages of the proposed converter are its simple control strategy, reduction in number of conversion stage, low input line current harmonics, and improvement in power factor. Analysis of the single-stage converter is carried out in continuous conduction mode of operation. Steady-state analysis of the proposed converter is conducted to obtain converter parameters. A systematic design procedure is also presented for a 12k W converter with a design example. The effect of load variation on SMPS is also studied in order to demonstrate the effectiveness of the proposed converter for the complete range of load conditions. A set of power quality indices on input ac mains for an SMPS fed from a single-stage converter is also presented for easy comparison of their performance.

• 대한건축학회논문집:구조계
• /
• 제34권8호
• /
• pp.13-18
• /
• 2018

The purpose of this study was to study on the estimation of green remodeling energy reduction tool in building construction. Green Remodeling Decision System that can predict the energy reduction effect in green remodeling is developed as a tool for simple remodeling of green remodeling considering users' convenience, so that it can quickly and comprehensively determine power peak load reduction factor technology. A preliminary simulation result of a short preliminary remodeling evaluation is DB. It will be developed as a tool that can be easily accessed by users such as web and apps.

• 한국건설순환자원학회논문집
• /
• 제9권1호
• /
• pp.100-108
• /
• 2021

이 연구의 목적은 최근 국내에서 개발된 섬유보강 고강도 콘크리트 설계지침(안)의 저감계수를 적용하여 확보하는 설계의 신뢰도지수를 분석하는 것이다. 설계지침(안) 개발을 위하여 수행된 재료실험 및 부재실험 데이터를 수집하여 재료강도 통계특성 및 부재강도 해석식에 대한 통계특성을 구한다. 재료통계특성과 설계지침(안)의 부재 해석식을 적용한 시뮬레이션을 수행하고 해석식의 통계특성과 종합하여 단면강도에 대한 통계특성을 산출한다. 국내 도로교설계기준과 콘크리트구조기준의 하중조합을 적용한 신뢰도분석을 수행하였으며, 설계지침(안)에서 제시한 재료 및 부재에 대한 저감계수를 적용한 설계는 목표신뢰도 지수를 만족함을 확인하였다.

• Computers and Concrete
• /
• 제10권1호
• /
• pp.1-18
• /
• 2012

This paper presents the details of studies conducted on hollow concrete block masonry (HCBM) units and wall panels. This study includes, compressive strength of unit block, ungrouted and grouted HCB prisms, flexural strength evaluation, testing of HCBM panels with and without opening. Non-linear finite element (FE) analysis of HCBM panels with and without opening has been carried out by simulating the actual test conditions. Constant vertical load is applied on the top of the wall panel and then lateral load is applied in incremental manner. The in-plane deformation is recorded under each incremental lateral load. Displacement ductility factors and response reduction factors have been evaluated based on experimental results. From the study, it is observed that fully grouted and partially reinforced HCBM panel without opening performed well compared to other types of wall panels in lateral load resistance and displacement ductility. In all the wall panels, shear cracks originated at loading point and moved towards the compression toe of the wall. The force reduction factor of a wall panel with opening is much less when compared with fully reinforced wall panel with no opening. The displacement values obtained by non-linear FE analysis are found to be in good agreement with the corresponding experimental values. The influence of mortar joint has been included in the stress-strain behaviour as a monolith with HCBM and not considered separately. The derived response reduction factors will be useful for the design of reinforced HCBM wall panels subjected to lateral forces generated due to earthquakes.

• Steel and Composite Structures
• /
• 제19권5호
• /
• pp.1077-1094
• /
• 2015

This paper presents an experimental study on the effectiveness of simultaneous application of carbon fiber-reinforced polymer (CFRP) and steel jacket in strengthening slender reinforced concrete (RC) column. The columns were 200 mm square cross section with lengths ranging from 1600 to 3000 mm. Ten columns were tested under axial load. The effects of the strengthening technique, slenderness ratio, cross-section area of steel angle and CFRP layer number were examined in terms of axial load-axial strain curve, CFRP strain, steel strip strain and steel angle strain. The experiments indicate that strengthening RC columns with combined CFRP and steel jacket is effective in enhancing the load capacity, ductility and energy dissipation capacity of RC column. Based on the existing models for RC columns strengthened with CFRP and with steel jacket, a design formula considering a slenderness reduction factor is proposed to predict the load capacity of the RC columns strengthened with combined CFRP and steel jacket. The predictions agree well with the experimental results.

• 한국지반공학회논문집
• /
• 제39권6호
• /
• pp.21-30
• /
• 2023

현장타설말뚝의 연암 근입부의 단위주면마찰력을 산정하는 방법 중 암반 벽면거칠기에 의한 산정 방법이 있다. 현장타설말뚝의 굴착 시공 시 암반 굴착공에 거칠기 장치를 설치하고 벽면 거칠기 모양을 측정하고 그 결과를 이용하여 주면마찰력을 산정하는 것이다. 본 연구에서는 암반벽면의 거칠기를 직접 측정한 결과와 하중전이 시험결과를 비교분석하여 거칠기시험에 의한 단위주면마찰력을 말뚝의 발생 변위에 대응하는 단위 주면마찰력으로 변환할 수 있도록 저감계수 R_f = -0.14n + 1.48(여기서, n은 하중전이시험에서 도출된 발생변위 δ를 말뚝직경 D로 나눈 변위비)을 제안하였다.

• Steel and Composite Structures
• /
• 제7권2호
• /
• pp.119-133
• /
• 2007

Based on stability theory of current rigid steel frames and using the three-column subassemblage model, the governing equations for determining the effective length factor (${\mu}$-factor) of the columns in semirigid composite frames are derived. The effects of the nonlinear moment-rotation characteristics of beam-to-column connections and composite action of slab are considered. Furthermore, using a two-bay three-storey composite frame with semi-rigid connections as an example, the effects of the non-linear moment-rotation characteristics of connections and load value on the ${\mu}$-factor are numerically studied and the ${\mu}$-factors obtained by the proposed method and Baraket-Chen's method are compared with those obtained by the exact finite element method. It was found that the proposed method has good accuracy and can be used in stability analysis of semi-rigid composite frames.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.74-77
• /
• 2005

Most of the loads in industrial power distribution systems are balanced and connected to three power systems. However, voltage unbalance is generated at the user's 3-phase 4-wire distribution systems with single & three phase. Voltage unbalance is mainly affected by load system rather than power system. Unbalanced voltage will draws a highly unbalanced current and results in the temperature rise and the low output characteristics at the machine. It is necessary to analyse correct voltage unbalance factor for reduction of side effects in the industrial sites. Voltage unbalance is usually defined by the maximum percent deviation of voltages from their average value, by the method of symmetrical components or by the expression in a more user-friendly form which requires only the three line voltage readings. If the neutral point is moved at the 3-phase 4-wire system by the unbalanced load, by the conventional analytical method, line and phase voltage unbalance leads to different results due to zero-sequence component. This paper presents a new analytical method for phase and line voltage unbalance factor in 4-wire systems. Two methods indicate exact results.