• The KIPS Transactions:PartA
• /
• v.8A no.2
• /
• pp.133-146
• /
• 2001

In a dynamic load distribution policies, each node gathers the current system sates information before making a decision on load balancing. Load balancing policies based on this strategy can suffer from processor thrashing. In this paper, we propose a new algorithm which attempts to decrease the frequency of the processor thrashing, the algorithm is based on the integration of three components. The first, the algorithm of which determine the size of jobs be transferred. The second, negotiation protocol with obtains a mutual agreement between a sender and a receiver on the transferring job size. And the third, a symmetrically-initiated location policy. The algorithm proposed in this paper used Siman IV as simulation tool to prove the improvement of performance. I analyzed the result of simulation, and compared with related works. The mean response time shows that there are no difference with existing policy, but appear a outstanding improvement in high load. The thrashing coefficient that shows the average response time, CPU overhead and the thrashing ratio at both the receiving and sending node has been used in the analysis. A significant improvement in the average response time and the CPU overhead ratio was detected using our algorithm when an overhead occurred in the system over other algorithm. The thrashing coefficient differed in the sending node and the receiving node of the system. Using our algorithm, the thrashing coefficient at the sending node showed more improvement when there was an overhead in the system, proving to be more useful. Therefore, it can be concluded that the thrashing ratio can be reduce by properly setting the maximum and minimum value of the system’s threshold queue.

• Design & Manufacturing
• /
• v.18 no.2
• /
• pp.29-34
• /
• 2024

This study intends to reduce forming load by adding die rotation to flange-upsetting process. Materials arc formed by the compression and rotational torque which are accrued from rotation of the lower die accompanied by axial compression of the punch. For the theoretic analysis of flange-upsetting process using rotation die, slab method was used. Furthermore, for the verification of the theoretic analysis results, FEM simulation using DEFORM 3D a commercial software was done, and through the model material experiment using Prasticine, the results were compared and reviewed. Flange-upsetting process using rotation die shows reduced forming load compared with process without die rotation and demonstrates uniform distribution of strain. And as for the effect of the reduction of forming load, the less the aspect ratio(h₀/d₀) and the greater friction coefficient, the greater effect is. With increase in die rotation velocity, the effect of forming load reduction also increases little by little, but its effect on forming load reduction is very negligible compared with other forming parameters. Theoretic analysis results and simulation results coincided pretty well. The flange-upsetting process using die rotation are evaluated as useful process that can produce reduction of forming load and uniform strain.

• Earthquakes and Structures
• /
• v.11 no.3
• /
• pp.407-420
• /
• 2016

The aim of this study is to investigate the effect of vertical ground motion (VGM) on seismic behavior of reinforced concrete (RC) regular frame with construction joints, and determine more proper modeling method for cast-in-situ RC frame. The four-story RC frames in the regions of 7, 8 and 9 earthquake intensity were analyzed with nonlinear dynamic time-history method. Two different methods of ground motion input, horizontal ground motion (HGM) input only, VGM and HGM input simultaneously were performed. Seismic responses in terms of the maximum vertex displacement, the maximum inter-story drift distribution and the plastic hinge distribution were analyzed. The results show that VGM might increase or decrease the horizontal maximum vertex displacement depending on the value of axial load ratio of column. And it will increase the maximum inter-story drift and change its distribution. Finally, proper modeling method is proposed according to the distribution of plastic hinges, which is in well agreement with the actual earthquake damage.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.40-45
• /
• 2000

Presented are the estimation of the probability distribution of fatigue crack growth life and reliability assessment of structures by simulating material resistance to fatigue crack growth along a crack path. The material resistance is treated as a Weibull stochastic process. A non-Gaussian stochastic fields simulation method proposed by Shimozuka, et al is applied with the statistical data obtained experimentally. Test results are obtained for $\Delta$K constant amplitude load in tension with stress ratio of R=0.2 and three specimen thicknesses of 6, 12 and 18mm. This simulation method is useful to estimate the probability distribution of fatigue crack growth life and the smallest life.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.4
• /
• pp.73-78
• /
• 2000

Presented are the estimation of the probability distribution of fatigue crack growth life and reliability assessment of structures by simulating material resistance to fatigue crack growth along a crack path. The material resistance is treated as a Weibull stochastic process. A non-Gaussian stochastic fields simulation method proposed by shimozuka, et al is applied with the statistical data obtained experimentally. Test results are obtained for $\delta K$ constant amplitude load in tension with stress ratio of R=0.2 and three specimen thicknesses of 6,12 and 18mm. This simulation method is useful to estimate the probability distribution of fatigue crack growth life and the smallest life.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.526-532
• /
• 2009

말뚝의 정재하시험을 통하여 항복하중 및 극한하중을 판별하는 다양한 방법이 제안되어 왔다. 말뚝의 지지력은 주면마찰력과 선단지지력의 합으로 나타내어 왔으나 말뚝 재하시험을 통한 항복 하중 및 극한하중의 판별법은 대체로 총 침하량에 대해 판별하거나 재하하중-침하 그래프로부터 산정되는 경우가 대표적이다. 본 연구에서는 현장 대구경 양방향 재하시험 결과를 활용하여 말뚝의 주면부와 선단부로 나누어 항복하중을 판별할 수 있는 방법을 제안하고자 한다.

• Journal of Power Electronics
• /
• v.19 no.5
• /
• pp.1153-1161
• /
• 2019

A current sharing controller is proposed in this paper for parallel-connected converters. The proposed controller is based on the calculation of the magnitudes of system current space vectors. Good current distribution between parallel converters is achieved with only one Proportional-Integral (PI) compensator. The proposed controller is analyzed and the circulating current impedance is derived for paralleled systems. The performance of the new control strategy is experimentally verified using two parallel connected converters employing Space Vector Pulse Width Modulation (SVPWM) feeding a passive RL load and a 2.2 kW three-phase induction motor load. The obtained test results show a reduction in the current imbalance ratio between the converters in the experimental setup from 53.9% to only 0.2% with the induction motor load.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1527-1532
• /
• 2008

45% of the sports accidents is the knee damage and the representative case is the damage of an Anterior Cruciate Ligament (ACL) and the Posterior Cruciate Ligament(PCL). Although the past different views of ACL reconstruction comes to an agreement, the disputes of PCL is remained yet. The most important engineering approach for these various surgery techniques is accurately to understand and to evaluate the fatigue behavior depending on the stress flow and the stress distribution under the allotted load and the cyclic load, which are caused by the graft fixing device, the proximal tibia of the PCL reconstructing structure. Therefore, this study is the basic research of these above facts. The current transtibial tunnel surgery using the cadaveric Achilles tendon grafts is chosen for the various PCL reconstruction. The relationships between the slippage, the extension ratio, and the slippage ratio by the heel bone fixing method and the soft tissue fixing method of the Achilles tendon were also defined. This research will be the essential data to help the resonable operating techniques for the next PCL reconstruction.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.5
• /
• pp.367-377
• /
• 2014

Paldang lake which is the most important water resource in Korea is classified as a stream type reservoir and water quality of Paldang lake can be significantly influenced by external pollutant source. So this study was aimed to determine focused control BOD and TP sources of each unit watershed upper Paldang lake through analysis of pollutant source distribution and pollutant runoff characteristics. Generated load, discharge load, delivery load and each load density of 11 unit watersheds upper Paldang lake were calculated using data of water quality and flow rate from pollutant sources and 74 small streams. As a result of generated load, discharge load and delivery load of BOD and TP from pollutant sources, the most BOD generated load was taken by livestock with 66% of total BOD discharge load and domestic had the most BOD discharge load, 42.7%. The ratio of delivery load of livestock and domestic was 36.4% and 34.3%, respectively. Livestock occupied high ratio of TP generated load, discharge load and delivery load with 82.5%, 44.4% and 46.7%, respectively. Gyeongan watershed which had high population density showed the highest BOD delivery load density of $14.6kg/km^2/d$ and the highest TP delivery load density with $1.23kg/km^2/d$ was analyzed in Cheongmi watershed including the biggest number of livestock. From these results, management of domestic sewer and livestock excrement was determined as a focused control pollutant source. And intensive management about domestic sewer in Gyeongan stream and livestock excrement in Cheongmi stream is required for water quality improvement of Paldang lake.

• Steel and Composite Structures
• /
• v.49 no.4
• /
• pp.381-392
• /
• 2023

This study experimentally investigates the flexural behavior of steel-UHPC composite slabs composed of an innovative negative Poisson's ratio (NPR) steel plate and Ultra High Performance Concrete (UHPC) slab connected via demountable high-strength bolt shear connectors. Eight demountable composite slab specimens were fabricated and tested under traditional four-point bending method. The effects of loading histories (positive and negative bending moment), types of steel plate (NPR steel plate and Q355 steel plate) and spacings of high-strength bolts (150 mm, 200 mm and 250 mm) on the flexural behavior of demountable composite slab, including failure mode, load-deflection curve, interface relative slip, crack width and sectional strain distribution, were evaluated. The results revealed that under positive bending moment, the failure mode of composite slabs employing NPR steel plate was distinct from that with Q355 steel plate, which exhibited that part of high-strength bolts was cut off, part of pre-embedded padded extension nuts was pulled out, and UHPC collapsed due to instantaneous instability and etc. Besides, under the same spacing of high-strength bolts, NPR steel plate availably delayed and restrained the relative slip between steel plate and UHPC plate, thus significantly enhanced the cooperative deformation capacity, flexural stiffness and load capacity for composite slabs further. While under negative bending moment, NPR steel plate effectively improved the flexural capacity and deformation characteristics of composite slabs, but it has no obvious effect on the initial flexural stiffness of composite slabs. Meanwhile, the excellent crack-width control ability for UHPC endowed composite members with better durability. Furthermore, according to the sectional strain distribution analysis, due to the negative Poisson's ratio effect and high yield strength of NPR steel plate, the tensile strain between NPR steel plate and UHPC layer held strain compatibility during the whole loading process, and the magnitude of upward movement for sectional plastic neutral axis could be ignored with the increase of positive bending moment.