• 한국표면공학회지
• /
• 제28권4호
• /
• pp.207-218
• /
• 1995

Tungsten(W) metal has excellent properties in heat-resistance, corrison-resistance and impact-resistance but W-Metal is hard to sinter because higher than $2,000^{\circ}C$ is required to sinter W-powder. Con-sequently, a deposit technique of Nikel Phosphorus(NiP) on W-powber by the liquid reduction precipitation method was performed. Sintering temperature of the resulting W-NiP composite was lowered around to $1,000^{\circ}C$, and the mechanical properties of the sintered body was studied. The most suitable conditions for NiP thin film deposit on W-Powder by the liquid reduction precipitation method, which are composition, concentration, pH and temperature of the liquid reduction solution, were considered. The activated sintering was carried out in a reducing condition furnace. Components and properties of the sintered body were investigated by the density and the hardness measurements, X- ray diffraction analysis, and microscopic photographs of the surface. Quantity of NiP thin film on W-powder could be varied by the change of the liquid reduction solution composition. The sintering temperature of W-NiP composite powder is lowered to $950^{\circ}C$ from $2,000^{\circ}C$ and the hardness is increased (ca. 720 Hv). Large shrinkage could be observed since density was increased from 5.5 to 11.0 g/$cm^2$ which 86.2% of theoretical density. W metal and $Ni_3P$ crystal were detected through X-ray diffraction on the sintered body. Perfectly activated sintering was observed by microscopic photographs.

• 한국결정성장학회지
• /
• 제26권3호
• /
• pp.95-100
• /
• 2016

본 연구에서는 염화주석, 하이드라진 그리고 수산화나트륨을 원료로 하여 용액환원침전법과 수열반응법을 이용하여 주석산화물 결정을 제조하여, 주요 실험 변수에 의한 결정상 및 형상을 XRD와 SEM을 이용하여 분석하였다. 원료의 몰 비에 따라 구형 및 판상의 주석산화물 결정을 얻을 수 있었으며, 그 결정상은 SnO, $Sn_6O_4(OH)_4$이었다. 그리고 수열반응법에 의하여 얻어진 결정 모양은 온도 조건에 따라 판상 및 꽃 모양의 SnO 결정이 얻어졌다.

• Nuclear Engineering and Technology
• /
• 제50권6호
• /
• pp.886-889
• /
• 2018

This article presented two-staged chemical precipitation for radioactive wastewater decontamination by using chemical agents. The total amount of radioactive wastewater was $35m^3$, and main radionuclides were Cs-137, Cs-134, and Co-60. Initial radioactivity concentration of the liquid waste was 2264, 17, and 9 Bq/L for Cs-137, Cs-134 and Co-60, respectively. Potassium ferrocyanide, nickel nitrate, and ferrum nitrate were selected as chemical agents at high pH levels 8-10 according to the laboratory jar tests. After the process, radioactivity was precipitated as sludge at the bottom of the tank and decontaminated clean liquid was evaluated depending on discharge limits. By this precipitation method decontamination factors were determined as 66.5, 8.6, and 9 for Cs-137, Cs-134, and Co-60, respectively. By using the potassium ferrocyanide, about 98% of the Cs-137 was removed at pH 9. At the bottom of the tank, radioactive sludge amount from both stages was totally $0.98m^3$. It was transferred by sludge pumps to cementation unit for solidification. By chemical processing, 97.2% of volume reduction was achieved. The potassium ferrocyanide in two-staged precipitation method could be used successfully in large-scale applications for removal of Cs-137, Cs-134, and Co-60.

• 한국표면공학회지
• /
• 제57권2호
• /
• pp.92-97
• /
• 2024

The LiBr aqueous solution, which is the absorption liquid of absorption refrigerator, must be replaced periodically because the concentration of impurities such as Cu²⁺, Fe²⁺, Ca²⁺, etc., increases due to corrosion of the tubes as the period of use increases, and the refrigeration efficiency decreases significantly. In order to reuse the waste absorption liquid, flocculation-precipitation method is mainly applied to precipitate the impurities, which requires hundreds of times the concentration of impurities and generates additional waste. In this study, a process for removing Cu ion impurities from cyclone electrolyzer by electrolytic reduction is presented in a small-scale facility without additional waste. It was confirmed that Cu ion impurities can be removed down to 1 ppm by electrolytic reduction process, and to further improve the removal rate, the mass transfer rate was increased by using a cyclone electrolyzer. The removal rate of Cu ions increased with the increase of flow rate and current density, and it was confirmed that Cu was removed at a rate of 1.48 ppm/h under the condition of 330 mL/sec and 2.5 mA/cm².

• Bulletin of the Korean Chemical Society
• /
• 제26권4호
• /
• pp.563-568
• /
• 2005

The Pt/C and Pd/C catalysts were prepared from conventional chloride precursors by adsorption or precipitation-deposition methods. Their activities for hydrogenation reactions of cyclohexene and acetophenone were compared with those of commercial catalysts. The Pt/C and Pd/C catalysts obtained from the adsorption procedure reveal higher hydrogenation activity than commercial catalysts and the catalysts prepared by the precipitation-deposition method. Their improved performances are attributed to the decreased metal crystallite sizes of Pt or Pd formed on the active carbon support upon the adsorption of the precursors probably due to the same negative charges of the chloride precursor and the carbon support. Under the preparation conditions studied, the reduction of the supported catalysts using borohydrides in liquid phase is superior to a gas phase reduction by using hydrogen in the viewpoint of particle size, hydrogenation activity and convenience.

• 한국생물공학회:학술대회논문집
• /
• 한국생물공학회 2005년도 생물공학의 동향(XVI)
• /
• pp.355-359
• /
• 2005

분별침전 공정에서 순도 및 수율에 미치는 온도의 영향을 확인하였다. 분별침전을 위해 일정 온도에서 보관할 경우와 단계적으로 보관 온도를 하강하는 경우에 대한 분별침전 효율을 확인하였다. 일정온도$(0^{\circ}C)$에서 보관할 경우 높은 수율$({\sim}84%)$을 얻을 수 있는 반면 단계적으로 보관 온도를 하강할 경우 상대적으로 높은 순도$({\sim}79%)$를 얻을 수 있었다. 또한 단계적으로, 큰 폭으로 보관 온도를 하강 시킬 경우 더 높은 순도를 얻을 수 있었다. 저장온도$(-20^{\circ}C{\sim}12^{\circ}C)$를 일정하게 유지할 경우 paclitaxel 순도 면에서 $0^{\circ}C$가 가장 효과적이었으며 온도변화에 따른 수율은 거의 영향이 없었다. 따라서 최종 정제를 위한 전 처리 공정으로 분별침전 공정이 간단하고 매우 효과적임을 알 수 있었다.