본 논문은 천리안 위성의 추진계를 간략하게 소개하고 천리안 위성의 발사 및 초기 위성운용 수행 임무 중 위성 추진계의 일련의 과정에서 측정된 원격측정치를 제시한다. 일부 원격측정치는 기 개발된 프로그램의 계산결과와 비교하였다. 추진계의 압력변화는 주로 두단계로 구성된다. 첫 번째 단계는 위성 추진계의 초기화, 즉 안전을 위해서 추진제 탱크 후 단부터 추력기 상단까지 충전된 헬륨 가스를 진공인 우주공간으로 빼는 배출단계를 시작으로, 이 빈 배관망에 산화제와 연료를 각각 채우는 충전단계를 거치고 마지막으로 추진제 탱크의 압력을 일정한 압력까지 올리는 가압단계이다. 두 번째 단계는 목표궤도에 이를 때까지 수행하는 액체원지점엔진의 연소 단계이며, 이 단계에서는 추진제 탱크의 압력을 일정하게 유지 하기 위해서 가압제인 헬륨을 사용한다. 이 프로그램은 향후에 개발되는 정지 궤도복합위성의 기초 설계자료 생성에 사용할 수 있을 것이다.
본 연구는 기존의 인젝터와 새로운 형태의 인젝터를 비교분석 함으로써 소형 추력기의 성능을 연구하였다. 기존의 인젝터는 볼록한 표면에 8개의 노즐로 구성되어 액체 추진제를 분사하는 형태로 제작되었다. 우리가 제안한 새로운 형태의 인젝터는 오목한 표면에 4, 5, 6, 8, 9개의 노즐로 구성된 충돌형 인젝터이다. 노즐의 구멍을 통해 분사되는 액체추진제는 축 방향으로 한 점에서 부딪히게 설계되었으며, 이는 분사되는 액체 추진제의 입자를 더욱 세분화하여 사방으로 일정하게 분무할 수 있도록 하였다. 본 논문에서는 전산유체역학, 입자 유속계 및 고속 카메라를 이용하여 분무 가시화 및 인젝터의 성능을 연구 하였다.
디젤은 높은 volumetric density$[VD,\;kg\;H_2/m^3]\;(>100)$와 gravimetric density$(GD,\;\%\;H_2)\;(>17)$를 가지는 우수한 수소저장매체 중의 하나이다. (Liquid Hydrogen의 경우 VD와 GD가 각각 50, 18 정도) 본 연구는 이러한 디젤연료의 개질에 적합한 촉매선정 및 반응특성에 관한 연구를 실시하였다 촉매는 자체 선정한 3가지 촉매(NECS-1, NECS-2, NECS-3)와 2가지 상용촉매(FCR-HCl4, FCR-HC35. Sud-Chemie, Inc)에 대하여 조사하였다. 실험결과 NECS-1이 디젤개질에 가장 적합한 것으로 판단되었다. 이와 함께 촉매 층의 길이에 따른 온도 및 농도를 분석하였으며, 디젤개질을 위한 연료의 delivery 문제로 인한 촉매 층 내의 급격한 온도 변화특성을 확인할 수 있었다. 또한 촉매 층 상단부에서 발생한 발열량을 하단부의 흡열부에 효과적으로 전달하는 것이 ATR(Autothermal Reforming) 반응 특성에 깊게 연관되어 있음을 확인할 수 있었다.
The objective of this work is to numerically reveal the effect of equivalence ratio change on the simultaneous reduction of NOX and soot emissions from the simulated-EGR compression ignition engine containing CO2. An experiment was conducted by using a single-cylinder common-rail injection system engine, an intake control system, and exhaust emissions analyzers. The numerical analysis results were validated under the same experimental conditions. To investigate the effect of equivalence ratio by simulated-EGR containing CO2, the O2, N2, and CO2 mole fraction were changed in the initial air conditions to the cylinder. The results were analyzed in terms of peak cylinder pressure, indicated mean effective pressure, indicated specific nitrogen oxide, and indicated specific soot. It was revealed that ignition delay characteristics and heat release rate (ROHR) characteristics were not significantly different according to the equivalence ratio. However, as the equivalence ratio increased from 0.68 to 0.83, the maximum combustion pressure and IMEP decreased by about 6.5% and 9.4%, respectively. In the case of ISFC, as is well known, the trend is opposite of IMEP. In the case of ISNO, as the equivalence ratio increased, less NO was generated, and as the equivalence ratio increased by 0.05, the ISSoot value of about 10% increased.
NOx, PN and CO emissions from diesel trucks make up a significant portion of domestic air pollutant emissions. Therefore, test vehicles with various emission standards and driving modes were selected to evaluate the emission characteristics of regulated pollutants (NOx, PN, CO) in medium-duty trucks. As a result of test, all test vehicles were satisfied with Euro 5 or 6 regulation. NOx emissions of Euro 6 vehicles with after-treatment of LNT + DPF were lower than those of Euro 5 vehicles with DPF. In WLTC mode, all vehicles have high NOx emissions at section of extra high speeds, which are determined by increased fuel consumption and high combustion temperatures. CO and PN emissions from all vehicles were found to be low at section of low speeds. Also, The NO2/NOx ratio was analyzed at 7-23% in each mode, and the NO2/NOx ratio increased as the average vehicle speed increased. In NIER 9 mode, the CO, HC, and PN emissions were higher under cold conditions of engine than hot conditions of engine. In addition, vehicles with after-treatment system of LNT have similar NOx emissions level in this study.
Recently, 1-D model-based engine development using virtual engine system is getting more attention than experimental-based engine development due to the advantages in time and cost. Injection rate profile is the one of the main parameters that determine the start and end of combustion. Therefore, it is essential to set up a sophisticated model to accurately predict the injection rate as starting point of virtual engine system. In this research, procedure of 1-D model setup based on AMESim is introduced to predict the dynamic behavior and injection rate of diesel injector. As a first step, detailed 3D cross-sectional drawing of the injector was achieved, which can be done with help of precision measurement system. Then an approximate AMESim model was provided based on the 3D drawing, which is composed of three part such as solenoid part, control chamber part and needle and nozzle orifice part. However, validation results in terms of total injection quantity showed some errors over the acceptable level. Therefore, experimental work including needle movement visualization, solenoid part analysis and flow characteristics of injector part was performed together to provide more accuracy of 1-D model. Finally, 1-D model with the accuracy of less than 10% of error compared with experimental result in terms of injection quantity and injection rate shape under normal temperature and single injection condition was established. Further work considering fuel temperature and multiple injection will be performed.
Kim, Keon-Sik;Song, Kun-Woo;Yang, Jae-Ho;Kang, Ki-Won;Jung, Youn -Ho;Kim, Gil-Moo
Nuclear Engineering and Technology
/
제35권1호
/
pp.14-24
/
2003
This work investigates the effects of Cr$_2$O$_3$ and oxygen potential on grain growth and densification of UO$_2$ pellets. Powder mixtures of UO$_2$ and 0.03-0.4wt% Cr$_2$O$_3$ were pressed and sintered in 3 different gas atmospheres: the $H_2O$-to-H$_2$ ratios were 5$\times$10$^{-4}$ , 1$\times$10$^{-2}$ and 3$\times$10$^{-2}$ In the first gas atmosphere the Cr$_2$O$_3$ contents below 0.2 wt% have an insignificant effect on grain size, but the Cr$_2$O$_3$ contents more than 0.3 wt% promote grain growth in the inner zone of a pellet but not in the outer zone. In both the second and third atmospheres, the grain size increases with the Cr$_2$O$_3$ content. With the same level of Cr$_2$O$_3$ content the grain size is larger in the second atmosphere than in the third. Sintering behavior and developed microstructure are discussed in terms of the reduction of C$r^2$O$^3$ to Cr, the dissolution of C$r^2$O$^3$ in UO$_2$, and liquid phase sintering.
소형위성 발사체 추진제 공급계 배관의 구부러짐으로 인하여 배관내부의 추진제 유동은 불균일하며 이는 터보펌프 전단의 블레이드의 파괴 및 후단의 가압된 추진제의 불안정성을 야기시킨다. 따라서 추진제의 효율적인 공급을 위하여 vane이 장착된 곡관 배관이 필요하며 내부에서의 유동장을 수치해석으로 규명하여 그 문제점을 해결할 수 있는 지 연구하였다. 따라서, 본 연구에서는 각각 90도와 45도로 구부러진 3인치 산화제 배관과 2.5인치 연료 배관의 구부러진 부분에는 $0\sim3$개의 vane을 등 간격으로 설치하였다. 3차원 Navier-Stokes 방정식을 풀기 위하여 상용코드를 이용하였으며, 곡관 배관 설계를 평가하기 위하여 각 90, 45도의 vane이 설치되지 않은 곡관과 $1\sim3$개의 vane이 장착된 곡관을 비교하였다. vane의 개수에 의한 배관 설계의 영향을 알아보기 위하여 90, 45도의 곡관에 vane이 0, 1, 2, 3개가 등 간격으로 장착이 되었을 때의 결과를 비교하였다. 배관내의 유동 균일성과 차압을 알기 위하여 속도크기와 압력분포를 계산하였다. vane이 많을수록 곡관의 각도가 클수록 곡관을 지난 유동은 더 균일해졌으나 배관 차압은 더 증가하였다.
본 논문에서는 AMESim(상용 소프트웨어)을 이용, 개방형 터보펌프식 엔진시스템을 모델로 하여 산업용 제어밸브를 적용한 시스템의 특성을 미리 확인하였다. 그 결과물을 토대로 하여 앞으로 발사체 제어밸브 개발할 계획이며, 밸브와 연계된 제어 및 밸브시험을 위한 설비 특성을 예측해 보았다. 시스템시험을 위해 장착할 각 산업용 제어밸브의 PID 값을 찾고자 하였으며, PI 및 PID 제어 방식을 이용하여 제어밸브의 과도 및 정상상태의 유동특성을 비교분석하였다. 제어밸브를 이용하여 추력제어 및 TDS 구현을 목적으로 하는 밸브설계와 시스템의 종합 모사시험을 위한 설비의 설계 조건을 또한 제시하였다.
Many ships in voyage experience weight and buoyancy distribution change by various reasons such as change of sea water density and waves, weather condition, and consumption of fuel, provisions, etc . The weight and buoyancy distribution change can bring the ships out of allowable trim, heeling angle. In these case, the ships should adjust trim and heeling angle by shifting of liquid cargo or ballasting, deballasting of ballast tanks for recovery of initial state or for a stable voyage. But, if the adjustment is performed incorrectly, ship's safety such as longitudinal strength, intact stability, propeller immersion, wide visibility, minimum forward draft cannot be secured correctly. So it is required that the adjustment of trim and heeling angle should be planned not by human operators but by optimization computer algorithm. To make an optimized plan to adjust trim and heeling angle guaranteeing the ship's safety and quickness of process, Uk! combined mechanical analysis and optimization algorithm. The candidate algorithms for the study were heuristic algorithm, meta-heuristic algorithm and uninformed searching algorithm. These are widely used in various kinds of optimization problems. Among them, heuristic algorithm $A^\ast$ was chosen for its optimality. The $A^\ast$ algorithm is then applied for the study. Three core elements of $A^\ast$ Algorithm consists of node, operator, evaluation function were modified and redefined. And we analyzed the $A^\ast$ algorithm by considering cooperation with loading instrument installed in most ships. Finally, the algorithm has been applied to tanker ship's various conditions such as Normal Ballast Condition, Homo Design Condition, Alternate Loading Condition, Also the test results are compared and discussed to confirm the efficiency and the usefulness of the methodology developed the system.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.