• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.969-972
• /
• 2004

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. In this paper the effect of doping amounts of $Al_2O_3$ on the electrical, optical and morphological properties were investigated experimentally, The results show that the structural and electrical properties of the film are highly affected by the doping. The optimum growth conditions were obtained for films doped with 2 wt% of Al203 which exhibit a resistivity of $8.5{\times}10^{-4}{\Omega}-cm$ associated with a transmittance of 91.7 % for 840 nm in film thickness in the wavelength range of the visible spectrum.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.19.1-19.1
• /
• 2010

The process of manufacturing printed electronics using printing technology is attracting attention because its process cost is lower than that of the conventional semiconductor process. This technology, which offers both a lower cost and higher productivity, can be applied in the production of organic TFT (thin film transistor), solar cell, RFID(radio frequency identification) tag, printed battery, E-paper, touch screen panel, black matrix for LCD(liquid crystal display), flexible display, and so forth. In general, in order to implement printed electronics, narrow width and gap printing, registration of multi-layer printing by several printing units, and printing accuracy of under $20\;{\mu}m$ are all required. These electronic products require high precision to the degree of tens of microns - in a large area with flexible material, and mass productivity at low cost. As such, the roll-to-roll printing process is attracting attention as a mass production system for these printed electronic devices. For the commercialization of this process, two basic electronic ink technologies, such as conductive ink and polymers, and printing equipment have to be developed. Therefore, this paper addressed basis design and test to develop fine patterning equipment employing the roll-to-roll printing equipment and electronic ink.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.143-146
• /
• 2003

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. The influence of the substrate temperature, working gas pressure and discharge power on the electrical, optical and morphological properties were investigated experimentally. The consideration on the effect of doping amounts of Al on the electrical and optical properties of ZnO thin film were also carried out. ZnO:Al films with the optimum growth conditions showed resistivity of $9.42{\times}10^{-4}\;{\Omeg}-cm$ and transmittance of 90.88% for 840nm in film thickness in the wavelength range of the visible spectrum.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.351-351
• /
• 2011

Graphene has drawn great interests because of its distinctive band structure and physical properties[1]. A few of the practical applications envisioned for graphene include semiconductor applications, optoelectronics (sola cell, touch screens, liquid crystal displays), and graphene based batteries/super-capacitors [2-3]. Recent work has shown that excellent electronic properties are exhibited by large-scale ultrathin graphite films, grown by chemical vapor deposition on a polycrystalline metal and transferred to a device-compatible surface[4]. In this paper, we focussed our scope for the understanding the graphene growth at different conditions, which enables to control the growth towards the application aimed. The graphene was grown using chemical vapor deposition (CVD) with methane and hydrogen gas in vacuum furnace system. The grown graphene was characterized using a scanning electron microscope(SEM) and Raman spectroscopy. We changed the growth temperature from 900 to $1050^{\circ}C$ with various gas flow rate and composition rate. The growth condition for larger domain will be discussed.

• 한국전기전자재료학회논문지
• /
• 제29권3호
• /
• pp.175-180
• /
• 2016

In this study, we proposed an optical compensation method to improve the symmetricity of contrast ratio for wide viewing angle IPS (in-plane switching) LCD. First, the phase retardation depending on the thickness of compensation film is calculated, and then the phase change is presented at the $Poincar{\acute{e}}$ sphere. The phase retardation and the polarization state of the light passing through the optical elements are caculated by using the EJMM (extended Jones matrix method). In addition, the transmittance and the contrast countour are also calculated by using the Berremann's $4{\times}4$ matrix method. The simulation is carried out for a IPS LC cell with positive A/C/A compensation film. From the standard deviation of the contrast ratio, we confirmed the symmetricity at each viewing angle is inversely proportional to the standard deviation and calculated the optimum design condition of the uniaxial compensation film for the IPS LCD.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.15.2-15.2
• /
• 2009

Manufacturing of printed electronics using printing technology has begun to get into the hot issue in many ways due to the low cost effectiveness to existing semi-conductor process. This technology with both low cost and high productivity, can be applied in the production of organic thin film transistor (OTFT), solar cell, radio frequency identification (RFID) tag, printed battery, E-paper, touch screen panel, black matrix for liquid crystal display (LCD), flexible display, and so forth. The emerging technology to manufacture the products in mass production is roll-to-roll printing technology which is a manufacturing method by printings of multi-layered patterns composed of semi-conductive, dielectric and conductive layers. In contrary to the conventional printing machines in which printing precision is about $50~100{\mu}m$, the printing machines for printed electronics should have a precision under $30{\mu}m$. In general, in order to implement printed electronics, narrow width and gap printing, register of multi-layer printing by several printing units, and printing accuracy of under $30{\mu}m$ are all required. We developed the roll-to-roll printing equipment used for printed electronics, which is composed of un-winder, re-winder, tension measurement system, feeding units, dancer systems, guide unit, printing unit, vision system, dryer units, and various auxiliary devices. The equipment is designed based on cantilever type in which all rollers except printing ones have cantilever types, which could give more accurate machine precision as well as convenience for changing rollers and observing the process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.408-411
• /
• 2003

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors, were prepared by using the capacitively coupled DC magnetron sputtering method. The influence of the substrate temperature, working gas pressure, discharge power and doping amounts of Al on the electrical, optical and morphological properties were investigated experimentally. The effect of bias voltage on the electrical properties of ZnO thin film were also studied. Films with lowest resistivity of $5.4{\times}10^{-4}\;{\Omega}-cm$ have been achieved in case of films deposited at 1mtorr, $400^{\circ}C$ with a substrate bias of +10V for 840nm in film thickness.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.939-942
• /
• 2004

Al doped Zinc Oxide(ZnO:Al) films, which is widely used as a transparent conductor in optoelectronic devices such as solar cell, liquid crystal display, plasma display panel, thermal heater, and other sensors were Prepared by using the capacitively coupled RF magnetron sputtering method. In this paper the effect of RF discharge power on the electrical, optical and structural properties were investigated experimentally. The results show that the structural and electrical properties of the film are highly affected by the variation of RF discharge power. The optimum growth conditions were obtained for films doped with 2 wt% of $Al_2O_3$ and 200 W in RF discharge power, which exhibit a resistivity of $10.4{\times}10^{-4}{\Omega}-cm$ associated with a transmittance of 89.66 % for 1000nm in films thickness in the wavelength range of the visible spectrum.

• 한국기계가공학회지
• /
• 제20권9호
• /
• pp.84-89
• /
• 2021

Indium tin oxide (ITO) transparent electrodes, which are used to manufacture organic light-emitting diodes, are used in light-emitting surface electrodes of display EL panels such as cell phones and TVs, liquid crystal panels, transparent switches, and plane heating elements. ITO is a major component that consists of indium and tin and is advantageous in terms of obtaining sheet resistance and light transmittance in a thin film. However, the optical performance of devices decreases with an increase in its thickness. A digital holography system was constructed and measured for the step measurement of the ITO thin film, and the reliability of the technique was verified by comparing the FE-SEM measurement results. The error rate of the step difference measurement was within ±5%. This result demonstrated that this technique is useful for applications in advanced MEMS and NEMS industrial fields.

• 문화기술의 융합
• /
• 제9권5호
• /
• pp.523-528
• /
• 2023

금속염 수용액과 고분자 매개체를 출발물질로 사용한 액상합성법으로 적색 파장을 방출하는 형광체를 합성하여, 태양전지 성능향상을 위한 소재로서의 적용 가능성을 검토하였다. Ca, Zn, Al, Eu 등 금속의 질산염을 사용하여 수용액을 제조하고 이것을 식물성 고분자인 전분에 함침시킨 전구체를 소결하여 CaZnAlO:Eu 형광체 분말을 합성하였다. 합성한 CaZnAlO:Eu 형광체 분말의 표면구조 및 성분분석을 주사전자현미경(SEM)과 에너지분산형 X-선분광법(EDS)으로 분석하였다. PL측정 결과 650-780nm의 근적외선영역의 발광파장을 가지는 적색형광체가 성공적으로 합성되었다. XRD 분석결과 단일상을 가진 순수한 CZA:Eu³⁺ 형광체가 합성된 것을 확인하였다. SEM, EDS 분석 결과 합성한 Ca₁₄Zn₆Al_9.93O₃₅:Eu³⁺_0.07 형광체 분말의 입도가 균일하며, 부활제로 사용한 Eu 이온이 존재하고 있는 것을 알 수 있다. 합성된 CZA:Eu³⁺ 형광체는 자외선이나 가시광선을 근적외선영역의 파장으로 하향변환하여 태양전지의 광 흡수효율을 높일 수 있는 소재로 활용될 수 있다.