• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.107-110
• /
• 2009

A basic design for a Technical Development Model (TDM) of liquid oxygen lines from the turbopump exit to the oxidizer valves of the combustion chamber and the gas generator was conducted to develop a turbopump-fed liquid rocket engine. The TDM is composed of straight lines, elbows, bellows, a branch, an orifice, flanges and a heat insulator. Materials were determined by consideration of operation conditions, weight constraint and manufacturing procedures. The size and the location of each component were determined by flow analysis of the required flowrate and the pressure loss. Basic designs of the components were conducted by consideration of the operating temperature and the maximum expectation operating pressure. The safety factors were evaluated by structural analysis of design of each component.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.2
• /
• pp.86-93
• /
• 2016

Performance tests of a 75-tonf liquid rocket engine turbopump were conducted. The performance of sub-components - two pumps and a turbine - and their power matching were measured and examined firstly near the design speed under the LN2 and kerosene environment. In the real propellant - LOX and kerosene - environment tests, design and off-design performance of turbopump were fully verified in regime of the rocket engine operation. During the off-design performance tests, turbopump running time was set longer than the engine operating time to verify the pump operability and set the pump inlet pressure close to design NPSHr to investigate pump suction capability in parallel. It has been found that developed-turbopump satisfied all of the engine required performances.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.26-35
• /
• 2004

As part of thrust control technology research on turbopump-fed type liquid-propellant rocket engine system, the low frequency dynamic characteristics of turbopump was investigated. It can be described that a turbopump system has a 1st-order lag element. When the value, which was resulted by subtraction of the variation of turbine moment with respect to the variation of revolution number from the variation of pump moment with respect to the variation of revolution number, was positive, the time constant of the 1st-order lag element was positive which stood for a stable system. Increasing the above-mentioned valve within positive range leaded to the increase of response and to the decrease of controllability.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.4
• /
• pp.249-254
• /
• 2008

Hydrodynamic performance test of a turbopump for a liquid rocket engine is carried out. The turbopump is composed of an oxidizer pump, a fuel pump and a turbine, and the two pumps are driven by the turbine. In the test, water is used for the pumps as working media and air is used for the turbine. Performance parameters of pumps and a turbine are drawn, and a power balance between the pumps and the turbine are calculated. The calculation shows a good power balance, which implies that the pump component tests, the turbine component test and the assembly test are reliably performed. At the starting period of the test, pressure rise-flow rate curve of a pump gradually approaches the ideal curve which could be obtained by very slow starting.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.375-383
• /
• 2005

The present paper describes the first development of a LOX/kerosene type turbopump in Korea. The liquid rocket engine, that the turbopump can be applied to, has a 30-ton(metric) level of vacuum thrust and employs a gas generator cycle. The turbopump consists of two single-stage centrifugal pumps, that is, LOX and kerosene pumps, and one single-stage impulse turbine. Inter-propellant seal(IPS) is located between the LOX pump and the kerosene pump to avoid any interaction between the propellants. A series of component and TPU(Turbopump Unit) test has been completed in the level of simulant propellants and ready for hot firing tests.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.6
• /
• pp.98-104
• /
• 2015

Excessive thrust acting on the rotor of pump can cause the damage of pump or the decrease of pump lifetime. Therefore, for ensuring the safety of LOX pump of a liquid rocket engine, the thrust of pump rotor is estimated by similarity tests. Axial thrust is indirectly measured by an axial thrust measurement unit positioned outside pump. Radial thrust is calculated based on pressure distribution of volute scroll. As a result, axial and radial thrust are increased when the flowrate of pump decreases. However, both thrusts do not affect the stability of pump rotor since their values are not large.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.358-362
• /
• 2005

An effective control of the axial thrust of a turbopump is one of the critical issues for its operational stability. In order to assure the stability of a turbopump-type fuel pump for a liquid rocket engine, an axial thrust measurement system was developed and a series of axial thrust tests were performed in water environment. In the tests, the axial thrust of the fuel pump at the design flowrate satisfied the axial force condition of the bearing of the pump. Also, it was found that by using orifices with different geometries in the secondary flow passage the overall axial thrust of the pump could be controlled.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.447-450
• /
• 2012

An analysis of chill-down process was performed for 30 tonf Turbopump-Gas generator coupled tests. The chill-down process must be fulfilled before liquid rocket engine test using cryogenic propellant. Cavitation, damage and/or combustion instability due to bubble of propellant must be eliminated by chill-down process in a test specimen, especially cryogenic pump. The analysis of test data obtained by 30 tonf TP-GG coupled tests was performed in order to be based on the test process of KSLV-II liquid propellant rocket engine which will be developed. To macroscopically understand the process of chill-down from the viewpoint of test procedure the temperatures of important part and total time of chill-down process were analyzed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.35-38
• /
• 2007

Aiming at time-dependent performance prediction of Liquid Rocket Engine(LRE) system, Modular Program for Conceptual Design of LRE is reviewed, and a modeling and dynamic analysis of rocket engine system with reference to Rocket Engine Dynamic Simulator(REDS) is outlined. Component modeling is based on classical thermodynamic and inviscid theories, and were formulated mathematically in terms of essential parameters. Essential design parameters are addressed. The rocket engine is modeled as a system of pipes with various hydraulic elements, and then the operate characteristic of that elements are simulated by solving conservation equation sequentially.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.1
• /
• pp.68-76
• /
• 2022

Upper stage of the Korea Space Launch Vehicle-II(KSLV-II) uses a 7-tons class liquid rocket engine and is an open gas generator cycle with a turbopump supply method that uses kerosene/liquid oxygen as the propellant combination. This study first provided a brief overview of the design and development process of the upper stage engine. In addition, it introduced the solutions and results applied to some of the problems that occurred during the development process of the upper stage engine.