• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.2
• /
• pp.164-170
• /
• 2001

The influence of unsteady wake on the flow and heat transfer characteristics in a four-vane linear cascade was experimentally investigated. The unsteady wake was generated with four rotating rectangular plates located upstream of the cascade. Tested inlet Reynolds number based on chord length was set to 66,000 by controlling free-stream velocity. A hot-wire anemometer system was employed to measure turbulent velocity components. For the convective heat transfer coefficients measurement on turbine blade surface, thermochromic liquid crystal and gold film Intrex were used. It was found that the unsteady wake enhances the turbulent motion in the cascade passage and accordingly promotes the development and transition of boundary layer. It was found that the heat transfer coefficients on the blade surface increase as the plate rotating speed increases. However, the increasing of heat transfer coefficients is not significant in the case that Strouhal number is higher than 0.503.

• Analytical Science and Technology
• /
• v.12 no.3
• /
• pp.224-229
• /
• 1999

Recently, many studies for the supported liquid membrane (SLM) using a carrier have been actively reported. Polymeric cation exchange membrane was synthsized by dissolving monensin carrier of antibiotic material in organic solvent. Then the SLM was applied to the Nernst-Planck and Fick equations and membrane potential and membrane permeability were measured respectively. The results showed the high selectivity towards alkali metal ions and the SLM showed linear relationship with low concentration. However, linear relationship did not appear at high concentration. This is explained by means of the new theory of the stagnant layer and the slop of logarithm value was linear for the up-hill transport phenomena of membrane transport.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.7
• /
• pp.864-870
• /
• 1999

An experimental study Is conducted in a four-vane linear cascade in order to examine the influence of the wake behind rectangular bars on the flow and heat transfer characteristics. Flow and heat transfer measurements are made for the inlet Reynolds number of 66000(based on chord length and free-stream velocity). Turbulent intensity and stress are measured using a hot-wire anemometer, and to measure the convective heat transfer coefficients on the blade surface liquid crystal/gold film Intrex technique is used. Each of experimental cases is characterized by the unsteadiness measured at the entrance of the cascade. The wake behind the rectangular bars enhances the turbulent motion of the flow in the cascade passage. It also promotes the boundary layer development and transition. The results show that heat transfer coefficients on the blade surface increase with increasing unsteadiness.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.2
• /
• pp.151-156
• /
• 2000

Effects of alignment layers on pretilt nagle generation and electrical characteristics in nematic liquid crystal(NLC) by using photo-alignment techniques on polyimide PI) surface with side chain were studied. The generated pretilt angle of the NLC on rubbed PI surface with 1-layer is almost the same as that with the 2-layers. However, the generated pretilt angle of the NLC on photo-induced PI surface with 2-layers is larger than that with the 1-layer. The different mechanism of pretilt generation in NLC was observed on the rubbing and photo-alignment method. Therefore, the pretilt angle of the NLC on photo-induced PI surface is attributed to surface roughness due to photo-dissociation on the polymer with UV light irradiation on PI surface. We observed the same characteristics of voltage-transmittance (V-T) and response time for 1- and 2-layers on PI surface. Consequently, we sugest that the VHR of photo-aligned TN-LCD is higher than that of the rubbing-aligned TN-LCD.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.46.2-46
• /
• 1998

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.10a
• /
• pp.187.1-187
• /
• 1999

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.122.1-122
• /
• 1998

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.6
• /
• pp.868-874
• /
• 2002

A high-impulse, low-power, digital microthruster has been developed using low-boiling-temperature liquid propellant with high-viscosity fluid plug. The viscous fiction force of the fluid plug increases the blast pressure and the low-boiling-temperature liquid propellant is intended to reduce input power consumption. The three-layer microthruster has been fabricated by surface micromachining as well as bulk micromachining in the size of 7$\times$13$\times$1.5㎣. A digital output impulse bit of 6.4$\times$10$^{-8}$ Nsec has been obtained from the fabricated microthruster using perfluoro normal hexane (FC72) propellant and oil plug, resulting in about ten times increase of the impulse bit using one hundredth electrical input energy compared to the conventional multiple-shot microthruster.

• Journal of Mechanical Science and Technology
• /
• v.14 no.11
• /
• pp.1276-1285
• /
• 2000

The solubility, the surface concentration and the dissolution behavior of carbon dioxide in deep sea were numerically investigated. Base on the calculations the relations between the surface concentration of liquid carbon dioxide droplet with the hydrate film and the solubility and those between the ambient carbon dioxide concentration in the plume and the dissolution rate were obtained. The result show that a carbon dioxide droplet is released both at 1000 m in depth with the initial droplet diameter of 0.011 m or less and at 1500 m in depth with a diameter of 0.015 m or less, and the droplet is completely dissolved below 500 m in depth. The hydrate film acts as a resistant layer for the dissolution of liquid carbon dioxide, and the effect of the hydrate film on the dissolution of liquid carbon dioxide depended upon the depth.

• Journal of Powder Materials
• /
• v.4 no.4
• /
• pp.252-257
• /
• 1997

Cu-brazed layer between the sintered-cam(Fe-5Cr-lMo-0.5P-2.5C, wt%) and seamless steelpipe(0.25-0.35C, 0.3-1.0 Mn, bal Fe, wt%) in the camshaft shows a columnar structure of $\gamma$-phase growing from the steel pipe. Liquid phase sintered 60Fe-40Cu alloys are carburized to simulate the brazing process giving rise to the columnar growth. Liquid film migrations and columnar growth of $\gamma$-grains are observed in the carburized regions. The $\gamma$-grains grow in the same direction as the C-diffusion. Fe-solubility in the liquid of carburized region is higher than in the uncarburized by about 0.3 at%. The columnar growth is driven by the gradient of the supersaturated Fe-solute in the liquid between two adjacent $\gamma$-grains.