• 펄프종이기술
• /
• 제36권1호
• /
• pp.9-15
• /
• 2004

Micro inorganic solids and dissolved materials contained in the white water of linerboard process was obtained by centrifugation, and their characteristics were analyzed along with their effects on the mechanical properties of linerboard. Micro inorganic materials had little influence on tensile index and ZDT of UKP sheets. They showed rather a positive effect on mechanical properties of KOCC sheets due to adsorbed polymer. Mechanical properties of KOCC sheets decreased remarkably when the concentration of dissolved materials increased especially above 4000 ppm.

• 펄프종이기술
• /
• 제41권1호
• /
• pp.30-36
• /
• 2009

Cracking of scored or creased lines on boards is a serious problem in converting process of corrugated fiberboard. It is important to reduce the possibility of score crack in advance by controlling the related quality factors of linerboard. To find out the key properties affecting score crack, we carried out the correlation analysis between score crack and physical properties of linerboards. Score crack was evaluated by visual rating on surface crack after folding a linerboard using laboratory folding resistance tester. Thickness of linerboard was the most important factor to score crack. The critical limits of thickness and strain can be determined by correlation analysis for reducing the possibility of score crack.

• 펄프종이기술
• /
• 제38권5호
• /
• pp.60-65
• /
• 2006

The physical and mechanical properties of linerboard were shown to be affected by changing atmospheric conditions. Two atmospheric conditions were measured in order to investigate how they were affected by different atmospheric conditions on the physical and mechanical properties of domestic linerboard. The basis data set for the standardization research was provided in this study. It is confirmed that the relative humidity seemed to be a major factor on the quality deterioration of a linerboard. Experimental results have shown that the short span compression test (SCT) could be used to evaluate the quality characteristics of linerboardat different moisture content and relative humidity.

• 펄프종이기술
• /
• 제39권2호
• /
• pp.38-44
• /
• 2007

The hygroscopic property of paper is important for convertability and end use performance. When the board and corrugated fiberboard are exposed to low relative humidity, a trouble of score (or crease) cracking could occur. In this study, we evaluated the moisture content and mechanical properties of linerboard and corrugated board at the cyclic condition of low humidity to prevent a score crack trouble. As the relative humidity decreased from 50% to 38% and 25%, the moisture content of linerboard decreased about 7% to 6% and 4%. At low humidity, most of mechanical properties were improved except for strain. The linerboard exposed at 25% RH showed a remarkable reduction of strain by 11%. At the same relative humidity, linerboard and corrugated fiberboard showed the different property values depending on moisture hysteresis.

• 한국식품저장유통학회지
• /
• 제6권3호
• /
• pp.303-307
• /
• 1999

온도 및 습도 변화에 따른 라이너원지의 압축강도 열화를 측정한 결과 압축강도는 온도변화에 영향이 없는 것으로 나타났다. 습도변화의 경우 66% RH에서는 IK원지의 강도저하가 가장 낮은 것으로 나타났다. 93% RH에서는 KA원지의 강도저하가 40%로 가장 낮았으며 SK원지가 56%로 가장 높게 나타났다. 비압축강도의 경우 66% RH에서는 SC 마니라와 IK 원지가, 93% RH에서는 IK원지와 KA원지가 가장 우수하였다. 원 단위 압축강도에서는 습도를 무시할 경우 SK원지가 우수하였으나 66% RH와 93% RH에서는 모두 KA원지가 다른 원지보다 우수한 것으로 나타났다. 따라서 농산물 포장용 라이너로 KA원지를 사용할 경우 경제적이면서도 압축강도가 높은 골판지상자를 제조할 수 있을 것으로 판단된다.

• 펄프종이기술
• /
• 제44권3호
• /
• pp.34-40
• /
• 2012

In this study, new antibacterial materials were developed to manufacture a functional corrugated board. Sulfur solution, a new antibacterial solution made from inorganic sulfur in the laboratory, and other antibacterial mat erials were adopted to treat the surface of a linerboard. We measured the antibacteriocidal and bacteriostatic activities, as well as the fungal resistance of the surface-treated linerboards, to identify the antibacterial properties. The mechanical properties of the surface-treated linerboard were also determined in order to identify the effects of the antibacterial materials on linerboard properties. Linerboard treated with sulfur solution, PVOH, and sodium metasulfite showed the highest antibacterial activity, while linerboard treated with sulfur solution and nano sulfur showed the highest fungal resistance. It was identified that sulfur solution has effective antibacterial properties. The antibacterial materials did not affect the mechanical properties of the surface-treated linerboard, but the binder showed significant effects in terms of the burst strength, the compressive strength, and the stiffness of the linerboard.

• 펄프종이기술
• /
• 제40권5호
• /
• pp.53-59
• /
• 2008

This study was carried out to investigate the effect of photocatalysis using $TiO_2$ and UV applied for the COD reduction of wastewater in linerboard mill. Trials were done to obtain the optimum addition amounts of $TiO_2$ and $H_2O_2$ to the wastewater and find an appropriate pH condition for photocatalysis on $TiO_2$ for degrading COD. The photocatalytic reaction was applied to the wastewater collected after secondary activated sludge treatment in WWTP of linerboard mill. The optimum application of photocatalysis reaction was obtained under the addition conditions of 2 g/L of $TiO_2$ and 200 mg/L of $H_2O_2$ at pH 3.0, respectively. The removal efficiency of $SCOD_{Cr}$ by photocatalytic treatment was 86.4 % and higher than Fenton treatment in which removal efficiency was 67.4 %. It was concluded that the photocatalytic process using $TiO_2$ and UV could be applied to the wastewater treatment in linerboard mill and also to the dramatic drop-off in NBDCOD load from wastewater of tertiary treatment in WWTP.

• 펄프종이기술
• /
• 제36권3호
• /
• pp.44-51
• /
• 2004

The effect of refining conditions and grammage on the stiffness of linerboard was investigated. The correlations between Taber stiffness and resonance stiffness were very low due to the different measuring principle. The refining conditions did not affect sig nificantly on both Taber and resonance stiffness estimated here. This means that it is strongly recommended to find and apply the refining conditions which can reduce specific energy consumption. Taber stiffness showed very high correlation for the thickness and elastic modulus of linerboard, while the resonance stiffness showed much lower correlation. Effective thicknesses for Taber stiffness were very well fitted with measured thickness, while those for resonance stiffness depended on the grammage of linerboard.

• 펄프종이기술
• /
• 제44권1호
• /
• pp.58-64
• /
• 2012

As a first step to apply PVAm (polyvinylamine) on packaging paper by surface treatment, three types of linerboards were impregnated with PVAm solution. The effect of PVAm pick-up on strength properties of linerboard was investigated. The pick-up of PVAm was controlled by varying concentration of PVAm solution. It was found that dry tensile strength, tensile energy absorption, burst strength and compressive strength of linerboard were increased by applying PVAm. In addition, wet tensile strength was significantly improved with increasing PVAm pick-up. However, folding endurance was found to be decreased with increasing PVAm pick-up.

• 펄프종이기술
• /
• 제38권1호통권113호
• /
• pp.1-8
• /
• 2006

To overcome troubles in strength and process of linerboard caused by raw materials, a neutral sizing which is usual in fine paper making can be considered. A new sizing agent is necessary to show good performance in a system with high conductivity and COD. In this study, fast cure type AKD was examined as a new sizing agent and compared with conventional AKD. The effects of fixing agent addition and drying condition were also investigated. Fast cure type AKD which has a higher cationicity showed better sizing degree than conventional AKD in spite of low addition level and no curing treatment. And when fixing agent of sufficient amount was added, sizing degree was improved for both AKDs. High cationicity is a crucial factor for neutral sizing of linerboard for obtaining fast and stable sizing degree. Drying with temperature over $100^{\circ}$ was desirable for developing sizing degree.