• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권7호
• /
• pp.430-436
• /
• 2004

This paper presents an advanced control technique for power density maximization of the Brushless DC (BLDC) generator by using the linear tracking method. In a generator of given rating, the weight and size of the system affect the fuel consumption directly. Therefore, power density is one of the most important issues in a stand-alone generator. BLDC generator has high power density in the machine point of view and additional increases of power density by control means can be expected. Conventional rectification methods cannot achieve the maximum power possible because of hon-optimal current waveforms. The optimal current waveform to maximize power density and minimize machine size and weight in a nonsinusoidal power supply system has been derived, incorporated in a control system, and verified by simulation and experimental work. A new simple algebraic method has been proposed to accomplish the proposed control without an FFT which is time consuming and complicated.

• 한국수소및신에너지학회논문집
• /
• 제23권2호
• /
• pp.183-190
• /
• 2012

The research shows the experiment results according to the combustion characteristics and configuration of the linear generator of powerpack for the generating power applying the 2-stroke compact linear engine. The powerpack used in this paper consists of 2-stroke linear engine, linear generator and air compressor parts. For identifying the combustion characteristics and generating power of linear engine, some parameters were varied sucha as electric load, fuel input calorie, spark timing delay and equivalence ratio. Also generating power was confirmed at each operation conditions, when the air gap length of linear generator part was changed as each 1.0 mm and 2.0 mm. During the all operations, intake air was inputted under the wide open throttle. Mass flow rate of air and fuel was changed using mass flow controller, after these were premixed by premixture device, and then premixed gas was supplied directly into each cylinder. As a result, piston frequency and combustion characteristics were different at each conditions according to parameters affecting the combustion such as fuel input calorie, resistive load, spark timing delay and equivalence ratio. Consequently, these had an effect on generating power.

• 응용통계연구
• /
• 제27권3호
• /
• pp.475-485
• /
• 2014

일반화 선형모형(GLM)에 기초한 확률적 날씨 발생기(Stochastic weather generator)는 일일 날씨를 생성하는데 가장 일반적으로 사용되는 방법인다. 본 논문에서는 다층구조를 이용하여 기존의 GLM weather generator에 공간구조를 소개하였다. 계절별 총강우량의 overdispersion 현상을 효과적으로 제거하기 위해서 smoothing된 계절별 총강우량을 모형에 포함하였고 공간구조를 소개하기 위해서 Stochastic weather generator의 모형계수에 공간구조를 가지는 다변량 정규분포를 가정하였다. 그리고 제안된 공간구조를 가지는 GLM weather generator 모형을 우리나라 76개 지역에서 39년간 측정된 일별 강우량 관측자료에 적용하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -3
• /
• pp.1479-1482
• /
• 2002

In this work, a recursive parameter estimation algorithm estimates the mathematical model of steam generators every time step and a receding horizon controller is designed by using this estimated linear steam generator model of which parameters change as time goes on. It was shown through application to a linear model of steam generator that the proposed controller has good performance.

• Nuclear Engineering and Technology
• /
• 제46권3호
• /
• pp.387-394
• /
• 2014

A Slowing Down Time Spectrometer (SDTS) system is a highly efficient technique for isotopic nuclear material content analysis. SDTS technology has been used to analyze spent nuclear fuel and the pyro-processing of spent fuel. SDTS requires an external neutron source to induce the isotopic fissile fission. A high intensity neutron source is required to ensure a high for a good fissile fission. The electron linear accelerator system was selected to generate proper source neutrons efficiently. As a first step, the electron generator of an 80-keV electron gun was manufactured. In order to produce the high beam power from electron linear accelerator, a proper beam current is required form the electron generator. In this study, the beam current was measured by evaluating the performance of the electron generator. The beam current was determined by five parameters: high voltage at the electron gun, cathode voltage, pulse width, pulse amplitude, and bias voltage at the grid. From the experimental results under optimal conditions, the high voltage was determined to be 80 kV, the pulse width was 500 ns, and the cathode voltage was from 4.2 V to 4.6 V. The beam current was measured as 1.9 A at maximum. These results satisfy the beam current required for the operation of an electron linear accelerator.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.17-19
• /
• 2005

Variety of methods were discussed to reduce the cogging force in tubular permanent magnet type linear single phase AC generator. In paticular, the proposed methods depend on the variations of the permanent magnet construction. These methods Include two approaches in the form of sloped magnets, and conical magnets in addition to the conventional method of varying the magnet length. The undesired cogging force ripples were calculated by a two dimensional Finite Element Method(FEM). Moreover, the generated electromotive force in the stator coils was calculated fur each configuration of the permanent magnet. The experimental results agreed well with those obtained from the FEM-based simulations. Sufficient reduction in the cogging force was achieved over the range of 40% while the root mean square of the output voltage was maintained. It was found that the sloping the permanent magnet decreased the cogging force and at the same time increased the generated rms voltage of the AC generator. The performance of the designed linear AC generator was evaluated in terms of its efficiency, total weight, losses, and power to weight ratio.

• 한국산학기술학회논문지
• /
• 제15권9호
• /
• pp.5452-5459
• /
• 2014

현가장치에 적용 가능한 공진형 선형 발전시스템은 차량이 노면을 주행 시 발생되는 진동에너지를 수집하여 자가 발전기능을 수행하는 시스템으로써, 작은 노면 진동을 증폭하여 큰 발전량을 유도하기 위해 공진 현상을 적용하였다. 시스템의 진동변위 해석을 통해 세 가지의 각기 다른 발전기 아마튜어의 동적 거동을 시뮬레이션하였고, 이를 전자기 유한요소해석을 통해 실제 발전량을 계산 및 비교분석 하였다. 또한, 차량 노면주행 시, 다양한 가진 주파수에 공진현상을 적용하기 위해 발전기 아마튜어의 수를 증가시키는 다자유도 발전기로의 설계 개선을 수행하여 공진 점의 변화를 확인하고 이에 따른 발전량의 변화를 확인하였다. 최종적으로 동일한 제한조건(설치공간)하에서 약 35% 축소된 아마튜어를 설계하여 이전 대비, 1Hz 및 4Hz 가진환경에서 8.5 %, 13.8 % 감소하였고, 15 Hz의 가진 환경에서는 14.7 %의 증가 현상을 확인하였다.

• 한국해양환경ㆍ에너지학회지
• /
• 제17권3호
• /
• pp.174-181
• /
• 2014

선형발전기가 연결된 부이의 수직운동에 대한 시간영역 해석을 수행하여 얻은 시계열 자료를 가지고 선형발전기를 설계하고 전기에너지 출력특성 및 효율에 대해 살펴보았다. 1차 변환장치로 원통형 부이를 선택하였고, 2차 변환장치로 양측식 할박(Halbach) 배열 영구자석 가동자와 철심형 슬롯리스(Slotless) 고정자로 구성된 선형발전기를 사용하였다. 시간영역에서 부이의 수직운동 속도와 파랑하중을 입력자료로 직선형 영구자석 발전기가 설계되었고, 설계된 발전기는 규칙파 조건에서 유한요소 해석법을 적용하여 발전특성해석을 수행함으로써, 그 타당성이 입증되었다. 또한 불규칙파 조건에서 합리적이고 빠른 해석을 위해, 등가회로법을 적용하여 발전특성 해석을 수행하였는데, 그 결과 역시 매우 타당함을 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 C
• /
• pp.1236-1238
• /
• 1999

This paper presents an effect of cross magnetization to the generator simplified linear model which is used for multi-machine power systems. The formulae of reactances and time constant with saturation effect are presented. The simulation results show that cross magnetization has an effect which can not be ignored, to the reactances, time constant and eigenvalues in one machine infinite bus system of simplified linear model.

• ETRI Journal
• /
• 제32권1호
• /
• pp.93-101
• /
• 2010

A true random number generator (TRNG) is widely used to generate secure random numbers for encryption, digital signatures, authentication, and so on in crypto-systems. Since TRNG is vulnerable to environmental changes, a deterministic function is normally used to reduce bias and improve the statistical properties of the TRNG output. In this paper, we propose a linear corrector for secure TRNG. The performance of a linear corrector is bounded by the minimum distance of the corresponding linear error correcting code. However, we show that it is possible to construct a linear corrector overcoming the minimum distance limitation. The proposed linear corrector shows better performance in terms of removing bias in that it can enlarge the acceptable bias range of the raw TRNG output. Moreover, it is possible to efficiently implement this linear corrector using only XOR gates, which must have a suitable hardware size for embedded security systems.