• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.78-89
• /
• 1999

In this paper, to improve bandwidth amplitude fluctuation for the broadband signal in indoor propagation environment, we measured and analyzed broadband signal using a vertically polarized, horizontally polarized and circularly polarized antenna, conducting by frequency sweeping method in NLOS (Non-Line-of-Sight) environment. And, to investigate the optimum condition for the improvement of broadband propagation characteristics we also examined the effects of both human motions and transmission antenna height in the NLOS environment. As a result, in the case of NLOS environment, it was found that the amplitude deviation characteristics in frequency bandwidth can be improved by polarization diversity reception. Especially, we found that it is the best effective one to make polarization diversity reception branches, which install the circularly polarized antenna at transmitting end and install the polarized diversity branches received vertical or/and horizontal polarized wave at receiving end. The affection of a human motions is not so much in LOS and NLOS environment, but it can lead to the cause of burst error in indoor digital radio communications as the fade of signal strength become more deeper. And also, when raise the transmitting antenna up to the ceiling, the LOS and NLOS environment could be coexisted. In this case, it can be also inferred that frequency bandwidth amplitude deviation must be fundamentally improved by using polarization diversity reception technique to make the possibility of high transmission rate.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.9
• /
• pp.46-51
• /
• 2013

In this paper, the optimum placement and shape of UHF antenna on the unmanned aerial vehicle (UAV) are analyzed by using the electromagnetic (EM) simulation on the various locations. The FEKO was used for the EM-simulation. In order to reduce the complexity of simulation and minimize the runtime and memory usage, the composite aircraft structure is simplified as the PEC model excluding the radome structure. The simulation was performed on the wing and ventral fin of UAV, and the antenna shape used the monopole, dipole, and bent monopole antennas. When the monopole antenna is mounted under the wing, two antennas need to be mounted under the right and left wings, and those antennas have to be switched as the direction of UAV wing to the line of sight (LOS) data-link (DL) ground antenna. In the case of mounting under the ventral fin, one antenna can be used regardless of the direction of UAV wing to the LOS DL ground antenna. Also, the antenna gain is improved by the blockage reduction. The antenna gain is further improved by using the bent monopole antenna. The optimum solution of UHF antenna placement and shape on UAV is to mount the bent monopole antenna under the ventral fin.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.869-875
• /
• 2009

Safety is a big issue in the construction sites. For safe and secure management, tracking locations of construction resources such as labors, materials, machineries, vehicles and so on is important. The materials, machineries and vehicles could be controlled by computer, whereas the movement of labors does not have fixed pattern. So, the location and movement of labors need to be monitored continuously for safety. In general, Global Positioning System(GPS) is an opt solution to obtain the location information in outside environments. But it cannot be used for indoor locations as it requires a clear Line-Of-Sight(LOS) to satellites Therefore, indoor location monitoring system could be a convenient alternative for environments such as tunnel and indoor building construction sites. This paper presents a case study to investigate feasibility of Wi-Fi based indoor location monitoring system in construction site. The system is developed by using fingerprint map of gathering Received Signal Strength Indication(RSSI) from each Access Point(AP). The signal information is gathered by Radio Frequency Identification (RFID) tags, which are attached on a helmet of labors to track their locations, and is sent to server computer. Experiments were conducted in a shield tunnel construction site at Guangzhou, China. This study consists of three phases as follows: First, we have a tracking test in entrance area of tunnel construction site. This experiment was performed to find the effective geometry of APs installation. The geometry of APs installation was changed for finding effective locations, and the experiment was performed using one and more tags. Second, APs were separated into two groups, and they were connected with LAN cable in tunnel construction site. The purpose of this experiment was to check the validity of group separating strategy. One group was installed around the entrance and the other one was installed inside the tunnel. Finally, we installed the system inner area of tunnel, boring machine area, and checked the performance with varying conditions (the presence of obstacles such as train, worker, and so on). Accuracy of this study was calculated from the data, which was collected at some known points. Experimental results showed that WiFi-based indoor location system has a level of accuracy of a few meters in tunnel construction site. From the results, it is inferred that the location tracking system can track the approximate location of labors in the construction site. It is able to alert the labors when they are closer to dangerous zones like poisonous region or cave-in..

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.4
• /
• pp.819-830
• /
• 2017

An FM radio based PCL system is a passive radar technique for detecting the multiple moving targets from FM radio signals and tracking the trajectories of the targets by calculating the cross-correlation function of direct-path signal and target echo signals. However, the interference signals are received from a surveillance channel, which is designed to receive the target echo signals. Because of this problem, the target echo signals are masked by the strong interference signals and this makes it difficult to detect the true targets from the cross-correlation function. Adaptive filters are known as effective methods for suppressing the interference signals but there is a problem to present their accurate performances in the PCL system because many literatures used the cross-correlation function and the ratio of input and output power as a measure of the performance analysis. In this paper, a performance analysis method is proposed to evaluate the performance of interference cancellation algorithms. By using the property that each component of the filter weight vector is adjusted to suppress the specific interference signal, a performance measure of the interference signal suppression is defined by a function of adaptive filter weights. Based on the proposed method, we compare the performance of the adaptive filters used in the PCL system. Simulation results show that the proposed method can be very effective for evaluating the performance of interference cancellation algorithms.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.5
• /
• pp.267-273
• /
• 2012

The short-range communication module was developed in this paper which is suitable for the point-to-multipoint circumstances of 40 terminals communicating frequently in about 50 meters. The media access control layer of this communication module using asynchronous time-division multiplexing provides a fast and robust performance even in the worst case of simultaneous transmission events, and low packet error rate was measured a in LOS (Line-of-sight) circumstance by adding the function of acknowledge response to media access control layer. The difference test was carried out in order to measure the performance of point-to-multipoint communication. Two communication modules are respectively measured and graphed in 10 branches to 40 branches. The communication module developed in this paper showed a faster performance than the commercial Zigbee module in the specific case presented in this paper. Especially, in over 20 branches showed wide differences of the transmission speed. This results is caused by more network overhead of Zigbee whose wider applications needs the network layer and applicaiton layer besides media access control layer. Also, the asynchronous time-division multiplexing proposed in this paper are more suitable than CSMA-CA of Zigbee module when a lot of module ought to be frequently communicated in small area.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.6
• /
• pp.757-763
• /
• 2018

It is very difficult to achieve sufficient data rate and required quality of service due to the time-varying nature of the radio channel and various jammers such as path loss, delay, Doppler, shadowing and interference. Especially, the propagation path between the transmitting antenna and the tracking antenna mounted on the fuselage during the test and evaluation of the projectile system considered in this paper is based on the rapid movement of the projectile, the interference due to multipath fading due to the terrain, The propagation path may be blocked. In order to effectively improve the multipath fading occurring in the wireless communication system, a diversity combiner technique is required. In this paper, to derive the design and improvement schemes for the space diversity combiner technique among the diversity combiner schemes, the BER performance of maximum ratio combining (MRC) and selection combining (SC) In an adaptive SC / MRC diversity combiner that operates with MRC when it is lower than the specified threshold criterion when comparing the SNR between two signals received from the channel and operates with SC at high and combines the two received signals The BER performance of the system was compared and analyzed.

• Journal of Korea Game Society
• /
• v.7 no.4
• /
• pp.71-80
• /
• 2007

In this paper, we introduce an efficient GPU-based real-time rendering technique applicable to every kind of game. Our method, without an extra geometry, can represent terrain just with a height map. It makes it possible to freely go around in the air or on the surface, so we can directly apply it to any computer games as well as a virtual reality. Since our method is not based on any geometrical structure, it doesn't need special LOD policy and the precision of geometrical representation and visual quality absolutely depend on the resolution of height map and color map. Moreover, GPU-only technique allows the general CPU to be dedicated to more general work, and as a result, enhances the overall performance of the computer. To date, there have been many researches related to the terrain representation, but most of them rely on CPU or confmed its applications to flight simulation, Improving existing displacement mapping techniques and applying it to our terrain rendering, we completely ruled out the problems, such as cracking, poping etc, which cause in polygon-based techniques, The most important contributions are to efficiently deal with arbitrary LOS(Line Of Sight) and dramatically improve visual quality during walk-through by reconstructing a height field with curved patches. We suggest a simple and useful method for calculating ray-patch intersections. We implemented all these on GPU 100%, and got tens to hundreds of framerates with height maps a variety of resolutions$(256{\times}256\;to\;4096{\times}4096)$.

• Korean Journal of Remote Sensing
• /
• v.34 no.6_4
• /
• pp.1545-1553
• /
• 2018

Recent eruptive activity at Kīlauea Volcano started on at the end of April in 2018 showed rapid ground deflation between May and June in 2018. On summit area Halema'uma'u lava lake continued to drop at high speed and Kīlauea's summit continued to deflate. GPS receivers and electronic tiltmeters detected the surface deformation greater than 2 meters. We explored the time-series surface deformation at Kīlauea Volcano, focusing on the early stage of eruptive activity, using multi-temporal COSMO-SkyMed SAR imagery. The observed maximum deformation in line-of-sight (LOS) direction was about -1.5 meter, and it indicates approximately -1.9 meter in subsiding direction by applying incidence angle. The results showed that summit began to deflate just after the event started and most of deformation occurred between early May and the end of June. Moreover, we confirmed that summit's deflation rarely happened since July 2018, which means volcanic activity entered a stable stage. The best-fit magma source model based on time-series surface deformation demonstrated that magma chambers were lying at depths between 2-3 km, and it showed a deepening trend in time. Along with the change of source depth, the center of each magma model moved toward the southwest according to the time. These results have a potential risk of including bias coming from single track observation. Therefore, to complement the initial results, we need to generate precise magma source model based on three-dimensional measurements in further research.

• Fire Science and Engineering
• /
• v.33 no.6
• /
• pp.165-172
• /
• 2019

This study presents the design and manufacture of a self-contained breathing apparatus SCBA wireless communication module with a multipoint simultaneous full-duplex communication system to enable communication between team members wearing the SCBA system. It is necessary for fire-fighters to wear the SCBA system during extinguishing and rescue work at the fire site. Evaluation of the team communication module confirmed the feasibility of communication over more than 500 m in the test condition based on the line of sight. By implementing the Ad-hoc function, it was confirmed that the communication distance could be extended to 128 m by automatic routing up to 3 hoc. The vertical distance inside the building for successful communication was up to the 5th floor in the open staircase and up to the 3rd floor in the partitioned staircase. Furthermore, the performance testing of the communication module assuming a fire situation, confirmed that five team members correctly recognized the standard abbreviation of fire and wireless communication without a separate PTT key operation. In addition, the flame resistance was verified by exposing the module to a flame at 950 ± 50 ℃ for 5 s and then immediately extinguishing the flame.

• 전기의세계
• /
• v.43 no.1
• /
• pp.13-19
• /
• 1994

전자식 안정기는 최근 에너지 절약 정책과 관련하여 조명기기분야의 관심의 대상이 되었고, 절전 효율이 높은 고품질의 전자식 안정기에 대한 연구 개발 및 보급이 점점 더 확대되고 있는 추세이다. 일반적으로 전자식 안정기는 수십 KHz의 고주파에서 형광등을 구동시킴으로써 빛의 깜박거림과 가청잡음이 없으며, 저주파(60Hz)에서 사용하는 재래식 안정기(choke coil 방식)에 비해 높은 절전 효과를 얻을 수 있다[1-4]. 특히, 빌딩 사무실의 경우 낮에도 창가의 형광등이 켜져 있어서 막대한 전력을 낭비하고 있는 실정이므로, 일조량에 따른 자동 전력 조절이 가능한 전자식 형광등의 출현이 기대되고 있다. 전자식 안정기의 보급 확대를 위해서는 절전 효과 뿐만 아니라, 품질 문제, 수명 문제등을 고려하여야 하는 바, 예를 들면 순간 점등으로 방전초기의 sputtering 현상에 의한 lamp의 수명 단축, 미소 입력전압 변동에 따른 급격한 광출력의 변화로 절전 효과의 상실과 이상동작에 의한 스위칭 소자의 파괴 현상, 고주파 스위칭시 발생되는 전력손실과 noise등에 대한 대책이 요구되고 있다. 이러한 점을 개선하기 위해 추가되는 회로는 전자식 안정기 시스템을 더욱 복잡하게 만들고, 경제적으로 원가 부담을 주기 때문ㅇ 고품질의 전자식 안정기를 보급하는데 어려운 점으로 부각되고 있다. 본 고에서는 이러한 문제를 해결하기 위하여 조광기능을 포함한 다양한 제어회로와 보호회로를 조광기능을 포함한 다양한 제어회로와 보호회로를 1 chip에 수용하는 고품질의 전자식 안정기 제어용 집적회로에 대해서 기술하고자 한다.되어 나아갈 기술의 조류에도 부합하는 형태라 하겠다. 그러나 이 방식은 기 언급한 바와 같이 분산처리를 관장하는 운영체계의 개발에 상당한 고전이 따르리라 보여지며, 또한 보다 상세한 연구가 선행되어야 하겠지만 개발된 상용의 통신 프로토콜로서는 병렬처리의 성능을 극대화 하기에는 여러가지 제약이 있을 것으로 예측된다.기기들이 어떻게 응용되고 있는지 살펴보기로 하자. real informations would be available. Results are compared with those of optimal power flows.기능시험을 완료했으며 실제 line-of-sight(LOS) 시스템 구현에 적용중이다. 시대를 살아 갈 회원들이다. '컨텐츠의 시대'가 개막되는 것이며, 신세기통신과 SK텔레콤은 선의의 경쟁 과 협력을 통해 이동인터넷 서비스의 컨텐츠를 개발해 나가게 될 것이다. 3배가 높았다. 효소 활성에 필수적인 물의 양에 따른 DIAION WA30의 라세미화 효율에 관하여 실험한 결과, 물의 양이 증가할수록 그 효율은 감소하였다. DIAION WA30을 라세미화 촉매로 사용하여 아이소옥탄 내에서 라세믹 나프록센 2,2,2-트리플로로에틸 씨오에스터의 효소적 DKR 반응을 수행해 보았다. 그 결과 DIAION WA30을 사용하지 않은 경우에 비해 반응 전환율과 생성물의 광학 순도는 급격히 향상되었다. 전통적 광학분할 반응의 최대 50%라는 전환율의 제한이 본 연구에서 찾은 DIAION WA30을 첨가함으로써 성공적으로 극복되었다. 또한 고체 염기촉매인 DIAION WA30의 사용은 라세미화 촉매의