• Journal of Power Electronics
• /
• 제8권3호
• /
• pp.268-274
• /
• 2008

This paper presents a proposed position controller for a vector controlled induction motor. The position controller design depends on the rotational motion equations and a classical speed controller (CSC) performance. The CSC is designed to have the ability to track variable reference inputs and to provide a predefined system performance. Standard position controller in industry is presented to analyze its performance and its drawbacks. Then the proposed position controller is designed, based on the well defined rotational motion equations. The proposed position controller and the CSC are applied to control the position and speed of the vector controlled induction motor with different ratings. Simulation results at different operating conditions are presented to evaluate the proposed controllers' performance. The results show that the CSC can drive the motor with a predefined speed performance and can track a variable reference speed with an approximately zero steady state error. The results also show that the proposed position controller has the ability to effect high-precision positioning in a limited time and to track a variable reference position with a zero steady state error.

• 전기학회논문지
• /
• 제58권1호
• /
• pp.69-76
• /
• 2009

This paper describes sensorless high-speed control for 45,000rpm/22kw type PMSM by using iterative adaptive sliding mode observer. The proposed algorithm is based on sensorless vector control by on-line estimating the speed of rotor in the wide speed operating range between the starting operation. In addition, it shows the enhanced performance of the iterative adaptive observer by lessening its chattering and getting stable response in limited PWM period. The simulation and experiment results show the reliable performance of the proposed algorithm through starting to high speed operating range.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2001년도 춘계학술대회 논문집
• /
• pp.289-294
• /
• 2001

A curved track needs balanced super elevation according to the speed of the passing train and it is limited by maximum allowable amount. Therefore, passing speed at high degree curved track has to be controlled below the limits. Accurate position of the Speed Limit Post(SLP), which shows allowable speed of curved track dose not regulated so design and line side maintenance engineer adopt the position differently, When the rate of cant deficiency is considered on transition-curved section, the SLP should be located at the beginning point of the transition curve so as to control the speed of passing train and it will increase ride quality to passenger.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1998년도 제13차 학술회의논문집
• /
• pp.419-422
• /
• 1998

This paper presents how to design speed control of wound rotor induction motors with slip energy recovery. The speed is limited at some range of sub-synchronous speed of the rotating magnetic field. The problem with speed control by adjusting resistance value in the rotor circuit reduces the efficiency of power, because of the slip energy is lost when it passes through the rotor resistance. The control system is designed to maintain efficiency of motor, where it recovers loss energy by returning it to the system to improve the efficiency. A new PI control method of adaptive control [1］,［13］is applied for the system with cascade type PI controller on the main loop to keep the speed constant and the internal loop to adjust the rotor appropriated current of the load provides the good transient response without overshoot.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.147-150
• /
• 1995

High speed machining one of the most effectiv to improve machining accuracy and product in dies and mould. But a study on this is limited to Alumium, light metal etc. This paper presents machining characteristic of gray cast iron in high speed machining with tungsten carbide endmill. It is suggested to measure sutting force, tool wear, surface roughness, surface shape and select of cptimal cutting condition in the high speed machining of gray cast iron. Performance of high speed machine tool was estimated and the relationship between cutting phenomenon and machinabillity was described.

• International Journal of Internet, Broadcasting and Communication
• /
• 제7권2호
• /
• pp.117-122
• /
• 2015

Our research team proposed a flux-offset type fault current limiter as a new limiter. The flux-offset type fault current limiter uses a fault current limit technology based on the flux offset principle of the primary and secondary windings of a transformer. Stable fault current limit characteristics were achieved through a preliminary study. However, it was discovered that the initial fault current was not limited. Therefore, in this paper, a high-speed interrupter and a superconducting element were separately applied to the secondary winding of the flux-offset type fault current limiter and the operating characteristics were comparatively analyzed. In the experiment, when the superconducting element was applied to the secondary winding of the transformer, the initial fault current was limited while the limitation in the operation time was further shortened.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1081-1099
• /
• 2010

The TVM 430 system manufactured by Ansaldo STS in France is currently used in ground signalling system for Kyungbu HSR. It transmits the speed information to the on-board signalling system in the form of continuous signal via the track, and the rolling stock in Kyungbu HSR runs with 300km/h max. operating speed by using the corresponding information. Looking from the recent international trends in HSR, reducing the travelling time and increasing of the line capacity is promoting via the improvement of train speed. In case of TGV Est, they are realizing the normal operation with 320km/h max. operating speed by using TVM SEI signalling system, which is similar to TVM 430. Furthermore, in case Honam HSL, which is under construction, is looking over faster speed than the limited one of Kyungbu HSR(i.e. over 300km/h). In this paper, it is assumed that the existing TVM 430 ground signalling system is used and train speed is improved, therefore the number of block section to be increased depending on the increase of train speed and the standard speed to be used in this case is drawn via the simulation of the train model and described the method accordingly.

• Journal of Biosystems Engineering
• /
• 제32권3호
• /
• pp.145-152
• /
• 2007

Uniformity of spray deposit is one of the important factors in spray performance affecting efficacy of pest management. Distributions of spray deposit on artificial targets were measured and analyzed to enhance the efficiency of spray application. The research was studied to understand the deposition characteristics of spray droplets and to determine the optimum conditions of chemical application. The deposit and its pattern by the lower fan speed was more uniform and higher than that by the higher fan speed. The upward blasting distance was limited within 3 m, but the limit to the ground level was expanded the distance more than 3.5 m because of the accumulated droplets. When the fan speed was higher at the distance of 2.5 m, deposit reached to maximum. When the distance increased, deposit was getting lower. At the both fan speeds, the deposit was concentrated below $30^{\circ}$ because of the gravitation and the resistance of wind. This research can be useful in designing an orchard sprayer and its operation for various tree canopies. To achieve a uniform distribution of deposit using the air-blast type orchard sprayer, the application rate from the middle boom should be increased as the air velocity to the upward increased. The spray rate to the side boom should be limited in a minimal level.

• Smart Structures and Systems
• /
• 제21권5호
• /
• pp.601-609
• /
• 2018

The estimated probabilistic model of wind data based on the conventional approach may have high discrepancy compared with the true distribution because of the uncertainty caused by the instrument error and limited monitoring data. A sequential quadratic programming (SQP) algorithm-based finite mixture modeling method has been developed in the companion paper and is conducted to formulate the joint probability density function (PDF) of wind speed and direction using the wind monitoring data of the investigated bridge. The established bivariate model of wind speed and direction only represents the features of available wind monitoring data. To characterize the stochastic properties of the wind parameters with the subsequent wind monitoring data, in this study, Bayesian inference approach considering the uncertainty is proposed to update the wind parameters in the bivariate probabilistic model. The slice sampling algorithm of Markov chain Monte Carlo (MCMC) method is applied to establish the multi-dimensional and complex posterior distribution which is analytically intractable. The numerical simulation examples for univariate and bivariate models are carried out to verify the effectiveness of the proposed method. In addition, the proposed Bayesian inference approach is used to update and optimize the parameters in the bivariate model using the wind monitoring data from the investigated bridge. The results indicate that the proposed Bayesian inference approach is feasible and can be employed to predict the bivariate distribution of wind speed and direction with limited monitoring data.

• 한국대기환경학회지
• /
• 제23권5호
• /
• pp.585-595
• /
• 2007

Representative impacts and effectiveness of surface meteorological observation data assimilation were examined in order to use wind resources estimation around southern coastal area of the Korean Peninsula. The data used in study are observational wind and temperature data at 5 and 41 sites of Regional Meteorological Offices and Automatical Weather Systems, respectively. Observation wind speed data tends to show small effective radius with limited area. Especially assimilation impacts of data observed at peninsula type sites like Yeosu play only around the inside of the peninsula. This limited effective radius for wind speed is caused by the strong correlation between topography and wind speed. And the efficient radius for surface air temperature is larger than that of wind. Data assimilation for observational air temperature is useful to increase the accuracy of wind energy estimation. However assimilation of wind data requires special care in its application due to high sensitivity of topographical complexity.