• Korean Journal of Remote Sensing
• /
• v.35 no.6_3
• /
• pp.1261-1271
• /
• 2019

In case of Korea, limestone is very useful in various industries. These limestones are mainly produced in Gangwon-do. The study area, which is located in Okgye-myeon, Gangneung-si, Gangwon-do, is Okcheon metamorphic belt where abundant limestone, dolomite stone, and high-grade limestone are produced. The purpose of this study is to distinguish between calcite and dolomite among the limestone which is one of the representative carbonate rocks using the spectral characteristics. For this study,spectral characteristics were measured in the field and laboratory using FieldSpec® 3 spectrometer equipment from Analytical Spectral Device Inc. (ASD). In the field, the reflectance was measured below 50 cm from rock surface, and in the laboratory, the reflectance was measured in the rock surface, the polished surface, and the rock powder. As a result, absorption wavelengths of calcite and dolomite were significantly different around 2,330 nm. In particular, the absorption wavelength band position of dolomite appeared before 2,330 nm wavelength compared to calcite. The study could be used as a basis data for analysis of high-grade calcite limestone.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.1
• /
• pp.82-93
• /
• 2024

Since the cement industry generates more than 60 % of CO₂ during the clinker production process, supplementary cementitious materials are used worldwide to reduce CO₂ efficiently. Mainly used supplementary cementitious materials such as blast furnace slag and fly ash, which are used in various industries including the cement industry, concrete admixtures, and ground solidification materials. However, since their availability is expected to decrease in the future according to the carbon neutrality strategy of each industry, new supplementary cementitious materials should be used to achieve the cement industry's goal for increasing the additive content of Portland cement. Limestone is a material that already has a large amount in the cement industry and has the advantage of high grinding efficiency, so overseas developed countries established Portland limestone cement standards and succeeded in commercialization. This study was an experimental study conducted to evaluate the possibility of utilizing domestic PLC, the effect of fineness and replacement ratio on the physical properties of cement was investigated, and the environmental impact of cement was evaluated by analyzing CO₂ emissions.

• Advanced Composite Materials
• /
• v.18 no.2
• /
• pp.187-195
• /
• 2009

Much attention has been paid to the processing of inorganic whisker, especially calcium carbonate whisker, which can be used as reinforcement materials of polymer composite due to its low price. Unfortunately, the present synthesis technique of calcium carbonate whisker starts from calcinations of limestone, which involves high energy consumption and furthermore is a highly environment polluting reaction. In this report, needle-like aragonite was synthesized with a reversible solution reaction from limestone without calcination. Optical microscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques were used to characterize the morphology and crystal structure of intermediates as well as that of the product, aragonite. GCC (grinding calcium carbonate) powder was dissolved in an aqueous solution of magnesium sulfate with reflux and air flush. EDTA titration was used to evaluate reaction rate of the dissolution. A kinetics equation of the dissolution reaction was constructed, which displayed second-order kinetics with respect to the concentration of magnesium sulfate. A rate constant of $0.0015\;l^{-3}{\cdot}mol^{-1}{\cdot}h^{-1}$ was obtained. The dissolution reaction gave fiber-like magnesium hydroxide sulfate and gypsum crystal. Then needle-like aragonite with a length of $9.13\;{\pm}\;1.02\;{\mu}m$ and an aspect ratio of $5.64\;{\pm}\;1.37$ was synthesized from the dissolution product with $CO_2$ bubbling at $70^{\circ}C$.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.133-134
• /
• 2021

Limestone-calcined clay-Cement (LC3) concrete provides a solution for sustainability, durability, and profitability of concrete industry. This study shows experimental studies of the macro properties (residual compressive strength), the meso properties (mesoscopic images), and micro properties (thermogravimetric (TG) analysis, X-ray powder diffraction (XRD), FTIR spectra, Raman spectra, Mercury intrusion porosimetry, and SEM) of LC3 paste with various mixtures and at high elevated temperatures (20 ℃, 300 ℃, 550 ℃ and 900 ℃). We find (1) Regarding to macro properties, LC3 cementitious materials are at a disadvantage in compressive strength when the temperature is higher than 300 ℃. (2) Regarding to meso properties, when the temperature reached 550 ℃, all samples generated more meso cracks. (3) Regarding to micro properties, first, as the substitution amount increases, its CH content decreases significantly; second, at 900 ℃, for samples with calcined clay, a large amount of gehlenite crystalline phase was found; third, at elevated temperatures (20 ℃, 300 ℃, 550 ℃ and 900 ℃), there is a linear relationship between the residual compressive strength and the cumulative pore volume; fourth, at 900 ℃, a large amount of dicalcium silicate was generated, and damage cracks were more pronounced. The experimental results of this study are valuable of material design of fire resistance of LC3 concrete.

• Resources Recycling
• /
• v.30 no.6
• /
• pp.61-67
• /
• 2021

This work investigated the cementation of iridium from iridium-containing hydrochloric acid leachate. Zinc powder was used as the reducing agent, and the effects of the stoichiometric ratio of Zn/Ir, initial Ir concentration, initial pH, reaction time, and ultrasound irradiation on iridium recovery were investigated. When only the stirrer was used for cementation, the iridium recovery increased with the addition amount of zinc, and the recovery of about 70% at 40 times the stoichiometric ratio of Zn/Ir. In contrast, when employing ultrasonic irradiation with stirring, the recovery of iridium decreased at 20 times or less the stoichiometric amount of zinc. The recovery of iridium increased at 40 times the stoichiometric ratio of Zn/Ir. This result may be due to the ionization of zinc and re-dissolution of iridium during the ultrasound irradiation treatment. When a combination of ultrasonic irradiation and stirring was used for cementation, the iridium recovery increased by more than 27% compared to that when using only the stirrer. It was possible to recover 99% of iridium under the following conditions: reaction time, 60 min; initial pH, 0.01; volume of leachate, 100 mL; 1770 ppm Ir, 40 times the stoichiometric ratio of Zn/Ir.

• Journal of Powder Materials
• /
• v.12 no.2 s.49
• /
• pp.136-145
• /
• 2005

Graphite-Ni composite powders were synthesized by mechanical alloying(MA) and spray drying(SD). Fabricated powders as well as commercial graphite-Ni powders were thermally sprayed on mild steel substrates using high velocity oxygen fuel (HVOF) thermal spray process and flame thermal spray process. The effects of several process parameters on related properties in thermally sprayed coatings have been investigated and correlated with microstructures in this study. The results indicated that the desired properties can be obtained when commercial powders were applied using HVOF process, while coating properties in case of MA powder application were inferior to those in HVOF process in so far. However, it is suggested that property enhancement can be obtained if the fraction of hexagonal graphite phase can be increased in mechanically alloyed powders.

• Computers and Concrete
• /
• v.29 no.3
• /
• pp.187-199
• /
• 2022

The usability of waste materials as raw materials is necessary for sustainable production. This study investigates the effects of different powder materials used to replace cement (0%, 5% and 10%) and standard sand (0%, 20% and 30%) (basalt, limestone, and dolomite) on the compressive strength (f_c), flexural strength (f_r), and ultrasonic pulse velocity (UPV) of mortars exposed to freeze-thaw cycles (56, 86, 126, 186 and 226 cycles). Furthermore, the usability of artificial intelligence models is compared, and the prediction accuracy of the outputs is examined according to the inputs (powder type, replacement ratio, and the number of cycles). The results show that the variability of the outputs was significantly high under the freeze-thaw effect in mortars produced with waste powder instead of those produced with cement and with standard sand. The highest prediction accuracy for all outputs was obtained using the adaptive-network-based fuzzy inference system model. The significantly high prediction accuracy was obtained for the UPV, f_c, and f_r of mortars produced using waste powders instead of standard sand (R² of UPV, f_c and f_f is 0.931, 0.759 and 0.825 respectively), when under the freeze-thaw effect. However, for the mortars produced using waste powders instead of cement, the prediction accuracy of UPV was significantly high (R²=0.889) but the prediction accuracy of f_c and f_r was low (R²f_c=0.612 and R²f_f=0.334).

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.04a
• /
• pp.47-50
• /
• 2007

This study investigates the properties of light weight foamed concrete (LWC) designed with various content of fine grains (FG). Test showed that LWC containing diverse powder materials with addition, more than 15% of FG, tended to decrease the fluidity of fresh concrete. 10% of FG content in LWC exhibited 4mm in sinking depth, which is the lowest value. This value dramatically increased at more than 15% of addition. However the concrete incorporating LSP proportionally increased the sinking depth in overall. As for the strength, the values of all specimens were under standardization of KS, except for the concrete adding 5 and 10% of FG. Apparent density of LWC showed the lowest value when used 10% of FG which was satisfied the 0.5 grade in KS. For the thermal conductivity, it was also indicated at 0.5 grade in KS, which is under $0.160W/(m{\cdot}k)$. In conclusion, it is demonstrated that adding 10% of FG in LWC was effective in the aspects of recycling of materials, cost effectiveness and quality.

• Advances in concrete construction
• /
• v.10 no.6
• /
• pp.515-526
• /
• 2020

Cold-mixed asphalt mixture is a widely recommended asphalt pavement materials with potentially economic and environmental benefits. Due to the reduction of natural non-renewable mineral resources, powder minerals with similar properties are considered as new mineral fillers in asphalt mixtures. This study explored the feasibility of using cement to replace natural limestone powder (LP) in emulsified asphalt concrete modified by styrene-butadiene styrene copolymer. The experimental tests, including compressive strength, Marshall stability as well as moisture susceptibility test, were used to investigate the mechanical properties, the Marshall stability, flow value, as well as the moisture damage. In addition, the influence of material composition on the performance of asphalt concrete is explained by the microstructure evolution of the pore structure, the interface transition zone (ITZ), and the micromorphology. Due to mineralogical reactivity of cement, its replacement part of LP improved the mechanical properties, Marshall stability, but it will reduce the moisture susceptibility and flow value. This is because with the increase of the cement substitution rate, the pore structure of the asphalt concrete is refined, the width of ITZ becomes smaller, and the microstructure is more compact. In addition, asphalt concrete with a larger nominal particle size (AC-16) has relatively better performance.

• Journal of the Korea Institute of Building Construction
• /
• v.24 no.2
• /
• pp.181-191
• /
• 2024

In the realm of cement manufacturing, concerted efforts are underway to mitigate the emission of greenhouse gases. A significant portion, approximately 60%, of these emissions during the cement clinker sintering process is attributed to the decarbonation of limestone, which serves as a fundamental ingredient in cement production. Prompted by these environmental concerns, there is an active pursuit of alternative technologies and admixtures for cement that can substitute for limestone. Concurrently, initiatives are being explored to harness technology within the cement industry for the capture of carbon dioxide from industrial emissions, facilitating its conversion into carbonate minerals via chemical processes. Parallel to these technological advances, economic growth has precipitated a surge in construction activities, culminating in a steady escalation of construction waste, notably waste concrete. This study is anchored in the innovative production of calcium silicate cement clinkers, utilizing finely powdered waste concrete, followed by a thorough analysis of their mineral phases. Through X-ray diffraction(XRD) analysis, it was observed that increasing the substitution level of waste concrete powder and the molar ratio of SiO₂ to (CaO+SiO₂) leads to a decrease in Belite and γ-Belite, whereas minerals associated with carbonation, such as wollastonite and rankinite, exhibited an upsurge. Furthermore, the formation of gehlenite in cement clinkers, especially at higher substitution levels of waste concrete powder and the aforementioned molar ratio, is attributed to a synthetic reaction with Al₂O₃ present in the waste concrete powder. Analysis of free-CaO content revealed a decrement with increasing substitution rate of waste concrete powder and the molar ratio of SiO₂/(CaO+SiO₂). The outcomes of this study substantiate the viability of fabricating calcium silicate cement clinkers employing waste concrete powder.