• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.1
• /
• pp.83-90
• /
• 2019

LED lighting is spreading on the strength of LED lighting, and various government policies are being implemented. VLC research which is a wireless communication technology using lighting has been actively conducted, and it has been proven through many studies that a general LED light source such as a high-speed data transmitter can be used. But from now on, one of the main problems is the noise from side lights, which can be compared to the noise of radio broadcasts. So in this paper, we proposed a noise canceling model to remove the interference of ambient light by using an optical filter for a detachable VLC channel. In order to verify the proposed model, various high brightness RGB LED modules were used for comparative analysis. In addition, the applicability was verified through experiments using High Luminance LED lighting which is applied in real life.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.401-406
• /
• 2023

With the development of industry, fine dust is causing difficulties in various fields such as environment, health, and life, and a large amount of pollutants generated from human social activities are emerging as a serious environmental problem due to air pollution. Therefore, in this study, activated carbon was added to remove fine dust and volatile organic compounds by spinning cellulose acetate polymer fibers on a silicon support using the electrospinning method. By varying the activated carbon ratio and electrospinning time, the fine dust blocking effect and toluene adsorption performance were confirmed according to the activated carbon ratio and filter thickness. As a result, it was shown that the particles were effectively blocked with the increase in the electrospinning time due to the filter thickness increase. Adsorbed amount of toluene was increased with increase in activated carbon amount. Light transmittance was decrease with increase in electrospinning time, showing that there were light transmittance in filters electrospun for 20~30 minutes.

• Analytical Science and Technology
• /
• v.20 no.2
• /
• pp.155-163
• /
• 2007

Porosity paper evidence is encountered in case of forgery, kidnapping, fraud and terrorist activity. The present study was designed to evaluate the effect of three chemical reagents (Ninhydrin, 1,8-diazafluoren-9-one (DFO), Iodine fuming) to the quality of developed latent fingerprints on porosity printing papers and newspaper. In case of printing papers, print quality was better with Iodine fuming method than Ninhydrin and DFO treatment to developing latent fingerprints. Developing latent fingerprint on newspapers was achieved with Iodine fuming processing. The processing of Iodine fuming followed by DFO and by using blue light (orange red filter) exhibited better results with Iodine fuming. Enhancement of latent fingerprint detection image using Digital Imaging System was achieved.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.4
• /
• pp.362-367
• /
• 2017

This study was conducted to compare the particulate removal efficiency of the developed diesel particulate filter using various measurement methods in a high-speed marine diesel engine. A four-stroke mechanical marine diesel engine is used for the test, which has a maximum output of 403 kW and is coupled to an AC dynamometer to control engine speed and load. The test was conducted based on four steady-state engine operating conditions of E3 engine test cycle for the measurement of PM and soot removal efficiency using partial dilution method considered as gravimetric method and filter smoke number method as light absorption method, respectively. As a result of the removal efficiency measurement according to the application of diesel particulate filter, particulate matter was reduced from 76% to 91% and the soot was reduced by more than 90% while meeting the permissible engine back pressure. From these results, the applicability of diesel particulate filter adopted in high-speed marine diesel engines could be confirmed. In addition, based on the result that the particulate removal efficiency varies with different measurement methods, the necessity of unification of these methods could be identified.

• Applied Chemistry for Engineering
• /
• v.33 no.6
• /
• pp.600-605
• /
• 2022

In this study, nitrogen oxide (NO_x) removal experiments were performed using a graphene based ceramic filter coated with a V₂O₅-WO₃-TiO₂ catalyst. Graphene oxide (GO) was prepared by Hummer's method using graphite, and the reduced graphene oxide was produced by reducing with hydrazine (N₂H₄). Vanadium (V), Tungsten (W), and Titanium (Ti) were coated by the sol-gel method, and then a metal oxide-supported filter was prepared through a calcination process at 350 ℃. A NO_x removal efficiency test was performed for the catalytic ceramic filters with UV light in a humid condition. When graphene oxide (GO) and reduced graphene oxide (rGO) were present on the filter, the NOx removal efficiency was superior to that of the conventional ceramic filter. Most likely, this is due to an improvement in the adsorption properties of NOx molecules on graphene coated surfaces. As the concentration of graphene increased, higher NO_x removal efficiency was confirmed.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.E
• /
• pp.19-27
• /
• 2000

Particle Induced X-ray Emission (PIXE) and Elemental Analysis Syztem (EAS) were applied to the investiga-tion of the Characteristics and sources of wintertime atmospheric aerosols in Seoul. Atmospheric aerosols were collected by both fine and coarse fractions using a two-stage filter pack sampler from Kon-Kuk university during the winter season of 1999. PIXE was applied to the analysis of the middle and heavy elements with atomic numbers greater than 14(Si) and EAS was applied to the measurement of the light elements such as H, C and N. The fact that 64.2% of mass of fine particles in Seoul consists of the light elements (N, C , and H) suggests that the measurement of light elements is extremely important. The average mass concentration is Seoul was 38.6$\mu\textrm{g}$m(sup)-3. Elements such as Ca, Fe, Mg, and Ti appeared to have very low Fine/Coarse ratios(0.1∼0.4), whereas che-mical components related to anthropogenic sources such as Br, V, Pb, and Zn were observed to accumulate in the fine fraction. In the Asian Dust Storm(ADS) event, the concentation of soil components increased dramatically. Reconstruction of the fine mass concentrations estimated by a newly revised simple model was fairly in good agreement with the measured ones. Source identification was attempted using the enrichment factor and Pearsons coefficient of correlation. The typical elements derived from each source could be classified by this method.

• Journal of the Korean Institute of Gas
• /
• v.12 no.4
• /
• pp.63-68
• /
• 2008

This paper describes about the simulation and the experimental results of optical cavity with curved mirror surface and vertical mirror surface to improve the light intensity and efficiency of the optical sensors. When we use the vertical mirror surface, the distribution of light reached to the filter surface of detector shows an elliptical shape. Whereas, the curved mirror surface focuses the light into circular shape. Therefore, due to focusing effects in case of using curved mirror surface, the light intensity per unit area has been improved. Consequently, the output voltage of gas sensor has been expected to increase. Based upon the simulation, the experiment of gas sensor has been conducted with $CO_2$ gas from 0ppm to 2,500 ppm at 250 ppm step and $25^{\circ}C$, 45%R.H. ambient. The output voltage of gas sensor that has a curved mirror surface increases approximately 200 mV than that of vertical mirror surface.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.9
• /
• pp.807-813
• /
• 2015

In the present study, an interferometer system, which integrates the laser sensitivity control technique based on the theory of electronic speckle pattern interferometry, one of non-contact non-destructive analysis methods, was developed. This interferometry system receives an image from CCD cameras for each reference and object, and compares the photosensitivity of the object and reference images from imagification. For the purpose of this study, the photosensitivity of object and reference light is measured with power meters, and the amount of light was controlled with an ND filter with a reference light port matching photosensitivity. Using the plate specimen as the object, 0.6, 0.9, 1.2, and $1.5{\mu}m$ of out-plane deformation was made, and images were compared according to the difference in photosensitivity. After analysis, larger object deformations showed larger numbers of stripe patterns. Images became clearer and data error was reduced when the photosensitivity of object and reference light matched.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.11
• /
• pp.51-57
• /
• 2001

A light beam reflected from a machined surface generally containes information concerning about its surface roughness. This study examines and proposes a surface roughness measurement technique for on-machine measurement of machined surfaces. The technique is based on the measurement of a reflected laser beam pattern and the statistical analysis of its light intensity distribution. The surface roughness was found to be closely related to the standard deviation of the light intensity on the primary axis of the reflected pattern. An image acquisition device is made up of a laser diode, a half mirror, a screen, and a CCD camera. The exact image with the primary and secondary axes of a reflected laser beam pattern is calculated through such image processing algorithm as thresholding, edge detection, image rotation, segmentation, etc. A median filter and a surrounding light correction algorithm are improve the image quality and reduce the measuring error. Using the developed measuring device the effect of screen materials and workpiece and workpiece materials was investigated. Experimental results regarding to relatively high-quality surfaces machined by grinding, polishing, lapping processes have shown the measurement error is within 10% in the range of $0.1{mu}m~0.8{\mu}m R_q.$Therefore, the proposed method is thought to be effectively used when quick measurements is needed with workpieces fixed on the machine.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.219-221
• /
• 2015

We present our recent observations of SDSS J102102.25+174439.9, a new eclipsing white dwarf - main sequence WDMS binary with an orbital period of 0.14 days. This system belongs to the post common-envelope binary group as shown by the spectrum from the Sloan Digital Sky Survey. We obtained our data using the ULTRASPEC instrument installed on the 2.4-m telescope at the Thai National Observatory (TNO). Our multi-band observations reveal an unusual and persistent drop in brightness after the primary eclipse. These dips, which appear to show variations in amplitude, also have a complex shape that changes within days. Dips in WDMS systems have been observed on only one other occasion, in the light curve of QS Vir prior to the eclipse of the white dwarf. The dips in SDSS J1021+1744 are unique because they are present at different wavelengths and they occur approximately at similar phases. Hosting a DA white dwarf and an M4 companion star, this system is known to be the only WDMS to show these kind of dips in its light curve. It is possible that these dips are caused by ejected materials from an active companion star, such as in QS Vir. The light curve in the g' filter exhibits deep and narrow features, implying that the material which passes in front of the white dwarf in SDSS J1021 must be dense and small in size. Furthermore, we try to constrain the stellar and orbital parameters of SDSS J1021+1744 using the Binary Maker 3 software. We use g' and r' data for our light curve analysis to have a better approximation for the red dwarf star.