• Current Photovoltaic Research
• /
• 제12권1호
• /
• pp.24-30
• /
• 2024

To create an environment for growing ginseng sprouts, we developed a solar module that partially transmits and disperses light. A G to G type light transmission and dispersion solar module was developed using glass with a mist pattern applied, and the light dispersion effect of the developed module was confirmed through illuminance measurement. The output of one module is approximately 260 W, and the configuration consists of 48 cells in series in 4 strings. The cultivation system where the developed module will be installed was developed in the form of a container, and three units of 2.6 kW (260 W x 10 EA). The inside of the cultivation system consists of a shading screen, air conditioner, ventilator, plastic pot, etc. to create an environment for cultivating sprout ginseng. As a result of actually planting sprout ginseng, it was confirmed through verification that the plants were grown without any problems.

• ETRI Journal
• /
• 제39권6호
• /
• pp.859-865
• /
• 2017

This paper presents a method for determining the optimum active-area width (OAW) of solar cells in a module architecture. The current density-voltage curve of a reference cell with a narrow active-area width is used to reproduce the current density profile in the test cell whose active area width is to be optimized. We obtained self-consistent current density and electric potential profiles from iterative calculations of both properties, considering the distributed resistance of the contact layers. Further, we determined the OAW that yields the maximum efficiency by calculating efficiency as a function of the active-area width. The proposed method can be applied to the design of the active area of a dye-sensitized solar cell in Z-type series connection modules for indoor and building-integrated photovoltaic systems. Our calculations predicted that OAW increases as the sheet resistances of the contact layers and the intensity of light decrease.

• 한국전기전자재료학회논문지
• /
• 제31권3호
• /
• pp.182-187
• /
• 2018

In this study, 20.8% of a p-type Si bifacial solar cell was used to develop a photovoltaic (PV) module to obtain the maximum power under a limited installation area. The transparent back sheet material was replaced during fabrication with a white one, which is opaque in commercial products. This is very beneficial for the generation of more electricity, owing to the additional power generation via absorption of light from the rear side. A new model is suggested herein to predict the power of the bifacial PV module by considering the backside reflections from the roof and/or environment. This model considers not only the frontside reflection, but also the nonuniformity of the backside light sources. Theoretical predictions were compared to experimental data to prove the validity of this model, the error range for which ranged from 0.32% to 8.49%. Especially, under $700W/m^2$, the error rate was as low as 2.25%. This work could provide theoretical and experimental bases for application to a distributed and microgrid network.

• 마이크로전자및패키징학회지
• /
• 제27권4호
• /
• pp.55-60
• /
• 2020

태양광 발전소에 설치된PERC 태양광 모듈 스트링-어레이는 고전압의 전위차로 인해 여전히 potential-induced degradation(PID) 열화 현상이 여전히 보고되고 있다. 이는 태양전지 모듈 커버글라스의 Na+ 이온이 태양전지 봉지재(EVA)를 투과하여 셀 표면으로 전이되고 결함이 많이 분포되어 있는 ARC(SiOx/SiNx) 계면에 양전하가 축적됨으로써 shunt-Resistance(Rsh)가 감소되고 누설전류량이 증가되어 태양전지 출력이 저하되는 현상이다. 본 연구에서는 이를 방지하기 위해 나노임프린트 리소그래피(nano-imprint lithography, NIL) 방식을 이용하여 모스아이(Moth-eye) 나노 구조를 광학 필름 후면에 증착 하였고, 이를 커버글라스와 EVA 사이에 삽입하여 태양광 미니 모듈을 구성하였다. PID 열화 현상을 확인하기 위해 IEC 62804-1 규격에 기반한 셀 단위 PID 열화가속시험을 진행하였고, Light I-V, Dark I-V 분석을 통해 출력(Pmax), 효율(Efficiency), 병렬 저항(shunt resistance)을 확인하였다. 그 결과 기존의 태양전지는 초기 효율 19.76%에서 6.3% 감소하였으나 모스아이 나노 구조 광학 필름(Moth-eye film)이 적용된 태양전지는 0.6% 만 감소하여 PID 열화 현상이 방지되는 것을 확인하였고, 모스아이 나노구조를 통해 투과도가 4% 향상되어 미니 모듈 출력이 2.5% 향상되었다.