• Resources Recycling
• /
• v.11 no.4
• /
• pp.11-16
• /
• 2002

Analysis and separation of constituent materials of old car have been performed by using the industrial shredding line. For this aim, three old cars made by domestic automobile manufacturers, Sonata II, Sephia and Prince were chosen and delivered in pressed form without engine, tires and doors, etc. Shredding line was substantially composed of pre- and main-shredder. cyclone, magnetic separation, eddy current separation and man-power separation. From the separation of shredder products, iron scrap was observed to be the major material of old car accounting for 60.1 ％ of total weight and non-ferrous metals involving Al, Cu and Zn, etc. were about 2％. Light fluff, about 90％ of total fluff product, was comprised with plastic, fiber and sponge, etc. and the fraction of 5 cm undersize in light fluff was 70.5%. In case of heavy fluff, however. rubber and plastic were found to be the major constituent materials of it. Among the constituent materials of fluff, plastic showed the highest calorific value, more than 10,000 cal/gr and leather and rubber showed relatively high chlorine content, 10.3 and 2.55 wt%, respectively.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.5
• /
• pp.556-565
• /
• 2016

As a result of the enforced control of emission, many devices, including the diesel particulate filter, have been installed in diesel cars to reduce the emission of particulate matters. In this study, a car fire case has been investigated and analyzed. A car fire broke out after the vehicle traveled a distance of 1.4 km from a car service center. The car was provided with DPF cleaning when the DPF warning light came on. After being dismantled in the engine room, the car's engine and gearbox were investigated. The findings showed that the rear part of the DPF metal case was melted and punctured, while the honeycomb filter of the DPF was damaged. The car fire was caused by an overheated DPF associated with inaccurate maintenance practice. Therefore, the responsibility of the fire rested on the car service center that performed the DPF cleaning.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.923-924
• /
• 2010

• Journal of Auto-vehicle Safety Association
• /
• v.3 no.2
• /
• pp.11-16
• /
• 2011

In recent years, rapid-increasing market share of compact cars and SUVs has brought for both consumer and automaker to pay more attention on crash compatibility between the compact passenger vehicles and the light trucks (i.e., Pickups and SUVs). Vehicle compatibility regarding both self and partner protection in frontal crash of different class vehicles is one of hot issues in vehicle safety. Furthermore, it is expected that the amendment of UNECE-Regulation 94 to implement compatibility issues in couple of coming years. In this study, conceptual design of compatibility compliant frontal vehicle structure which subjects to improve? the distribution of frontal crash loading and structural engagement between vehicles is introduced. The effects of proposed vehicle structure on both possible candidates (i.e. FWRB, FWDB and PDB) for a compatibility evaluation test procedure and car-to-car crash are also investigated.

• Journal of the korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.15-20
• /
• 1983

The nature and the sources of sound in cars is discussed in the light of many previous works, and the importance of the system resonances inside cars is suggested. An investigation of a 'boom' problem in a small size passenger car is described. It was established that the 'boom' frequencies coincided with engine firing frequency and also with several system resonances. To find out main transmission path of the noise to the car interior, various possible sources were eliminated from the investigation by means of simple modification to the vehicle. Data on the structural modes of the body, and the acoustic modes of the passenger compartment at various forcing cases were obtained to provide better understanding of the problem. It was found that the acoustic resonance responsible for the boom was controlled largely the bending motion of the floor. To investigate the effect of the structural modification to the acoustic response, center floor of the car was reinforced. a great reduction of the noise inside the car especially at the offending speed range, was achieved by this modification.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.548-553
• /
• 2008

Low Floor buses have no steps to get on or get off the main cabin to provide the old and the handicapped with easy access. The car body for the low floor bus was designed to consider Korean physical standard, passenger capacity (standee, seated, handicapped), arrangement of vehicle components, and bus law or regulations. It was designed as an one body, without any reinforcement armature, which has light-weight sandwich constructions with glass epoxy skins, aluminum honeycomb cores and inner-frames. In this paper, torsion rigidity of the designed car body was evaluated and compared with that of a car body with reinforcement armatures in the cabin. Finite element method verified that the designed car body without reinforcement armatures could satisfy requirements of torsion rigidity.

• Journal of the Ergonomics Society of Korea
• /
• v.29 no.6
• /
• pp.959-964
• /
• 2010

Seat belt is an important means to protect drivers and passengers from the damages by car accidents. Many ways to increase the seat belt wearing rate have been proposed through human factors researches. The primary ways to increase seat belt use rate have emphasized the intention-behavior cycle. This study focused on the gap between intention and behavior. The gap may be bridged by the habit for seat belt use behavior. Divers following a desirable car starting sequence, from sitting on the chair, fastening seat belt, starting engine to moving a car, reported that higher belt wearing rate and unconscious behavior (automated response). That is, the habitualized procedure knowledge prevented drivers from forgetting to fasten their seat belt. The reminder systems such as warning light and warning sound could not significantly give an influence in remembering to fasten seat belt. In order to increase the seat belt use rate, the desirable car starting procedure should be included in the driving education program.

• International Journal of Computer Science & Network Security
• /
• v.24 no.3
• /
• pp.142-150
• /
• 2024

A conceptual model represents an understanding of a system that is going to be developed, which in this research, a driving simulation software to study driver behavior at signalised intersections. Therefore, video observation was conducted to study driver compliance behaviour within the dilemma zone at signalised intersection, with regards to driver's distance from the stop line during yellow light interval. The video was analysed using Thematic Analysis and the data extracted from it was analysed using Chi-Square Independent Test. The Thematic Analysis revealed two major themes which were traffic situation and driver compliance behaviour. Traffic situation is defined as traffic surrounding the driver, such as no car in front and behind, car in front, and car behind. Meanwhile, the Chi-Square Test result indicates that within the dilemma zone, there was a significant relationship between driver compliance behaviour and driver's distance from the stop line during yellow light interval. The closer the drivers were to the stop line, the more likely they were going to comply. In contrast, drivers showed higher non-compliant behavior when further away from stop line. This finding could help in the development of conceptual model of driving simulation with purpose in studying driver behavior.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.190-193
• /
• 2003

This paper Proposes 40 [KVA] rated SIV(Static Inverter) system for Light Rail Transit. The SIV Provide power of a fluorescent light in the car, Air-conditioner. and other equipments. To control output voltage it is used voltage control loop for constant voltage control and simultaneously used current control loop for instantaneous control at load changing. The Performance of SIV system will be verified by experimental results.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.101-104
• /
• 2008

This paper is a report of designing for LED lights driver unit. The main purpose of driver designing is high electrical efficient performance and intelligent control LED driver. This LED driver can be used for intelligent light control. This product expects to improve the light control by dimming instead of interlace on/off light control that increases the social cost such as car accidents and etc.