• 한국해양공학회지
• /
• 제11권4호
• /
• pp.249-261
• /
• 1997

A basic study on the lifting lug design has performed through the rational and systematic process. In order to evaluate the proper design-load distribution around lug eye investigation of contact force between lifting lug and shackle pin is performed using non-linear parametric analysis idealized by gap element models. Gap element modeling and nonlinear analysis procedures are illustrated and discussed based on MSC/NASTRAN. Some analysis and design guides are suggested through the consideration of several important effects such as stress distribution pattern, circumferential contact force distribution along the lug eye face, loading share rate between lug main plate and doubler, effect of loading direction, relation between applied force and deflection and size effect of shackle pin radius. Additionally optimum design studies are performed and general trends according to the variation of design parameters are suggested.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.7-12
• /
• 2004

Large-sized pins are usually used to lift and handle large low speed diesel engine crankshaft. There has then been a need to reduce and optimize the weight of the traditionally used pins. Making an hole by cutting the inside of the pin out was investigated in view of static and fracture strength. To compensate the stress increase caused by the introduction of the inner hole, the groove in the circumferential direction pre-existing on the pin is to be removed. Finite element analysis was carried out for both the original model and weight reduced model. Stress intensity factors for semi-elliptical defects assumed on the pin for the original model and weight reduced model was calculated using the ASME method and compared with the fracture toughness test result of the pin material. The diameter of the cutting hole for the revised model was determined based on the analysis results.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2011년도 특별논문집
• /
• pp.51-54
• /
• 2011

This paper presents methods for design and strength analysis of lifting lugs utilized in assembling, erection, and turning over of ship structures. Lifting lugs are designed in accordance with ASME BTH-1-2008; Design of Below-the-Hook Lifting Devices. Experimental tests for fillet welded joints were conducted to design weld size of lifting lugs and under-structures. The nonlinear finite element method, using MSC.Marc software, is employed for limit state assessment of lifting lugs in static loading conditions. The analysis considers nonlinearities in material properties and contact between lifting lug and pin.

• 대한조선학회논문집
• /
• 제40권4호
• /
• pp.59-65
• /
• 2003

With the fast growth of shipbuilding industry, in recent years several hundreds of thousands of lifting lugs for a year have been used. This paper is aimed at maximizing the recovering use of lifting lugs. In this study, we have evaluated the structural strength for present and modified lifting lugs under in-plane and out-of-plane load conditions. For this purpose, the equivalent stresses have been calculated by nonlinear elasto-plastic analysis using the finite element program ABAQUS. At the same time, the contact conditions between lifting lug and shackle pin are also considered.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2011년도 특별논문집
• /
• pp.82-89
• /
• 2011

In general, a number of lifting lugs have been used in shipbuilding industry and the D-type lugs are mainly used. The aim of this paper is to increase the cycle of the use and to reduce the size of lifting lugs to introduce lightweight shackle. In this study, nonlinear elasto-plastic analysis has been performed to confirm the ultimate strength of lifting lugs. In order to evaluate the proper design-load distribution around lug eye, the contact force between lifting lug and shackle pin has been realized by gab element model. Gap element modeling and nonlinear analysis are carried out using the finite element program MSC/PATRAN & ABQUS. Additionally the ultimate strength tests were performed to verify the structural adequacy of newly designed lifting lug and to insure safety of it. The D-10, 15, 20 & 40 ton models which are mainly used in the block erection are selected in the strength test. According to the results of the analysis and strength test, the ultimate strength of the newly designed lifting lugs has been estimated to exceed 3 times of design working load.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.192-194
• /
• 2005

Joint strength of spot friction welded 5J32 Al alloy were investigated according to the tool shape and the tool penetration depth. General spot friction stir welding tool consists of a shoulder having bigger diameter and a threaded pin projected from the shoulder, which resulted in the generation of large up-lifting of upper plate around the weld nugget because of the deeper penetration and the severe stirring effect of threaded pin. Two kinds of welding tools without the threaded pin were used to avoid the distortion and improve the joint strength. One was a simple cylindrical shape and the other was cylindrical shape with small projection. Therefore, the process was named as spot friction welding comparing to spot friction stir welding because spot friction welding don't use a stirring effect. Using the cylindrical shape tool with small projection, the up-lifting of upper plate were avoided and joint strength were superior to that of the joint using simple cylindrical shape tool. At the 0.5mm of too penetration depth using cylindrical tool with small projection, nugget pull fracture mode can be observed and shear fracture mode were dominant at the rest conditions.

• Restorative Dentistry and Endodontics
• /
• 제14권1호
• /
• pp.205-210
• /
• 1989

The purpose of this study was to observe the minim pins of Link plus (which has buttress thread and shoulder stop design) inserted into dentin and the dentin surrounding pin. The gingival walls of class II cavity were prepared with high speed handpiece in molar teeth not elapsed time after teeth were extracted, and pinhole of 2mm in depth was positioned about 1 mm to the dentinoenamel junction and minim pin was inserted with wrench. After initial examination of the specimens, the specimens were sectioned longitudinally and horizontally to the pins with carborundum disc and low speed diamond saw (Isomet Buehler Ltd) All specimens were coated Au of 250-300${\AA}$ in thickness with Ion Sputter JFC 100 and observed under Scanning Electron Microscope (JSM-35) The following results were obtained. 1. The shoulder stop was seated on the enterance of pinhole in gingival wall, and there were the irregular space between the pin and dentin at the enterance to the pin hole and flakes of dentin lifting from the dentin floor. 2. In case of section to pin horizontally or longitudinally, the dentin debris were observed in gap between pin and dentin, and small cracks were often seen in the dentin surrounding minim pins.

• 한국해양공학회지
• /
• 제25권2호
• /
• pp.101-107
• /
• 2011

In view of the importance of material reduction because of the jump in oil and steel prices, structural design studies for lifting lugs were performed. Hundreds of thousands of such lifting lug structures are needed every year for ship construction. A direct design study was reviewed using the developed design system to increase the design efficiency and provide a way of directly inserting a designer's decisions into the design system process. In order to understand the design efficiency and convenience of a lug structure, parametric studies for prototype lug shapes were performed using the developed design system. From these design studies, various patterns of design parameters for the lug structure according to changes in the main plate length were examined. Based on these parametric study results, design guides were developed for more efficiently suggesting structural data for enormous lug structures. Additionally, a more detailed structural analysis through local strength evaluations will be performed to verify the efficiency of the optimum structural design for a lug structure.

• 한국산학기술학회논문지
• /
• 제22권3호
• /
• pp.94-100
• /
• 2021

멤브레인(membrane) LNG 운반선 화물창(cargo containment) 공사의 생산성 향상을 위해서는 공사 작업대인 비계 시스템(scaffolding system)의 설치 기간 및 공정 단축이 요구된다. 이를 위한 효과적인 방안으로 모듈의 탑재 단위를 기존의 2단에서 8단으로 대형화하자는 의견이 수렴되고 있다. 하지만, 모듈의 대형화로 인해 탑재 하중이 증가하면 메인 수직 파이프를 연결해주는 핀(pin)과 홀(hole) 주위에 국부 응력이 증가하여 재료의 항복응력을 초과하게 되는 문제점이 발생한다. 본 연구의 목적은 이러한 문제점을 해결하기 위해 트리즈(TRIZ)를 도입하여 새로운 대형 모듈의 탑재 방안을 수립하는 것이다. 본 연구에서는 트리즈의 여러가지 문제해결 도구 중 하나인 40가지 발명원리를 활용하는 방안을 채택하였다. 먼저 기술적 모순을 도출하고, 공학변수를 선정하였으며, 모순행렬을 활용하여 기술적 모순을 극복하기 위한 효율적인 발명원리를 선정하였다. 선정된 발명원리를 통해 일반해결안 및 특정해결안을 도출하였고, 구조해석을 통해 구조물에 발생하는 응력이 낮은 수준임을 확인하였다. 수립된 탑재 방안을 적용한 대형 모듈의 실제 탑재에 성공함으로써 트리즈의 유용성을 확인하였다.

• 한국해양공학회지
• /
• 제23권2호
• /
• pp.104-109
• /
• 2009

In the view of the importance of material reduction due to the jump in oil and steel prices, an optimized structural system for lifting lugs was developed. Such a system is needed hundreds of thousands of times a year. A direct design process was added to this developed optimized system to increase the design efficiency and provide a way of directly inserting a designer's decisions into the design system process. In order to verify the system efficiency and convenience, several new prototype lug shapes were suggested using the developed system. From these research results, it was found that the slope of the main plate of the lug structure has a tendency to move from about 45 degrees to about 60 degrees and the design weight was reduced from an initial value of about 32kgf to about $15{\sim}19kg_f$ after the redesign. Based on these initial research results, an efficient reduction in steel weight was expected considering the enormous consumption of lug structures per year. Additionally, a more detail structural analysis through local strength evaluations will be performed to verify the efficiency of the optimum structural design for a lug structure.