• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 가을 학술발표회 논문집
• /
• pp.389-396
• /
• 1998

One solution to prevent deterioration due to expansion joint and to extend lifetime of short span bridges, is jointless integral abutment bridge. To understand behavior of pile foundation of skewed plate girder bridge with integral abutment, finite element analysis was performed for the model of different skew angle from 90。 to 50。. Comparison of stresses at pile and abutment was made for each case. It is found that effect of temperature change is major factor to influence the behavior of skewed integral abutment bridge.

• 조명전기설비학회논문지
• /
• 제27권3호
• /
• pp.43-49
• /
• 2013

Recently harmonics flowing into power system is increasing as the usage of semiconductor equipments and switching mode power equipments are increasing. Harmonics cause problems such as heat increasing and reduction in capacity of transformers, especially the harmonics flowing into a distribution transformer can lead to the lifetime reduction of transformer. In this paper, we are about to develop a device that can monitor harmonics in real-time as it is affixed to a distribution transformer. Unlike the existing expensive harmonic analysis device, a new harmonic analysis algorithm is proposed in order to implement low-cost equipment. The real-time harmonic analysis algorithm proposed in this paper allows implementation on low performance microcontrollers, thus it can monitor the harmonic in real-time as it is individually affixed to the transformer. Therefore, it would improve the reliability of the transformer and stable power system operation would be possible as it can prevent the transformer accidents in advance.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2007년도 정기 학술대회 논문집
• /
• pp.387-392
• /
• 2007

The loss of strength in an aircraft structure as a result of cyclic stress over a period of life time is an important phenomenon for aircraft analysis. Load/stress spectrum can be constructed from the occurrence frequency based on the load/stress histories during a service lifetime. In this paper, three types of fatigue spectrum was compared. The rainflow counting method was applied to concentrate the stress spectrum obtained from the flight loads recorder(FLDR). A fatigue analysis for different stress spectrum was performed by using LUSAS computer application.

• 소성∙가공
• /
• 제9권1호
• /
• pp.43-51
• /
• 2000

The die wear is one of the main factors affecting product accuracy and die life in hot forging process. It is desired to analyze die wear by developing wear prediction method combined with FE-simulatin and experiment. Lots of researches have been done into the wear analysis of cold forging die, and the results of those researches were successful, but there have been little applications to hot forging die giving successful results. That is because hot forging process has many factors influencing die wear, and there was not accurate in-process data. In this research, change of die surface hardness by thermal softening during the lifetime was obtained by experiment, and hardness distribution of cross section was measured. This wear analysis was applied to hot forging die, and gave comparatively good results compared with actual wear profile.

• Journal of Information Processing Systems
• /
• 제10권2호
• /
• pp.300-313
• /
• 2014

Various Time Synchronization protocols for a Wireless Sensor Network (WSN) have been developed since time synchronization is important in many time-critical WSN applications. Aside from synchronization accuracy, energy constraint should also be considered seriously for time synchronization protocols in WSNs, which typically have limited power environments. This paper performs analysis of prominent WSN time synchronization protocols in terms of power consumption and test by simulation. In the analysis and simulation tests, each protocol shows different performance in terms of power consumption. This result is helpful in choosing or developing an appropriate time synchronization protocol that meets the requirements of synchronization accuracy and power consumption (or network lifetime) for a specific WSN application.

• Journal of the Optical Society of Korea
• /
• 제17권2호
• /
• pp.182-187
• /
• 2013

We present a comparative experimental analysis of the thermal spectroscopic characteristics of a phosphosilicate (P)-based ytterbium-doped fiber (YDF) against an aluminosilicate (Al)-based YDF in the temperature range of 25 to $150^{\circ}C$. We also characterize the fibers as gain media in a cladding-pumped amplifier configuration. While both fibers exhibit comparable trends in their thermal characteristics, there are noticeable distinctions in the fluorescence lifetime reduction rate and the spectral dependence of the transition cross-sections. The P- and Al-based YDFs present thermal lifetime reduction rates of $0.012%/^{\circ}C$ and $0.026%/^{\circ}C$, respectively. In particular, in the spectral region at ~940 nm, the absorption cross-section of the P-based YDF undergoes significantly less thermal change compared to that of the Al-YDF. In the cladding-pumped amplifier configuration operating at a total gain of 10 dB, the Al-based YDF generally performs betters than the P-based YDF in the temperature range of 25 to $75^{\circ}C$. However, it is highlighted that in the high temperature range of over $75^{\circ}C$, the latter shows a less gain reduction rate than the former, thereby yielding higher relative output power by 3.3% for a 1060-nm signal, for example.

• 한국항공우주학회지
• /
• 제42권7호
• /
• pp.616-621
• /
• 2014

저궤도에서 운용되는 위성은 대기 저항에 의한 연료소모가 크며, 연료소모는 임무수명 및 발사무게에 영향을 미치게 되어 위성 형상에 따른 항력의 예측이 중요하다. 본 논문에서는 직접모사법을 이용하여 파라볼릭 안테나를 탑재한 저궤도 위성의 임무고도의 변화와 받음각에 따른 항력 및 항력 계수의 변화를 살펴보았다. 저궤도의 희박 기체의 거동을 모사하는 직접모사법의 적용성을 검증하기 위해 스타샤인(Starshine) 위성의 비행데이터를 이용하여 고도, 대기와 표면의 상호작용에 따른 항력 계수를 비교하였다. 결론적으로 계산결과로부터 저궤도 위성의 정밀한 궤도수명 계산에 적합한 항력 계수를 도출하였다.

• 성인간호학회지
• /
• 제28권6호
• /
• pp.701-708
• /
• 2016

Purpose: This study investigated Korean women in between age 30 to 60 who were obese or overweight in order to explore their self-perception based on lifetime phase. Methods: Focus group interviews were performed four times with six to eight participants in each group (a total of 27). Data were analyzed using inductive thematic analysis. Results: The data analysis from the interviews revealed recurring common themes: heavy heart, heavy body, resigned acceptance of their own condition, and compromise. The study also found that each age group had different concerns: concerning others' gaze on their obese appearances (30s), realizing their aging obese appearances (40s), recognizing red flags of their health with obesity (50s), and becoming ambivalent about their obese appearances (60s). Overall, their perceptions of being overweight were negative and stressful. Women in their 30s and 40s were more interested in their appearances, and thus were more obsessive about weight gain. In contrast, women in their 50s and 60s were more accepting of their physical appearances, and thus were more concerned about living healthy than losing weight. Conclusion: These results may be useful to consider when developing tailored weight-control programs for obese and overweight Korean women. Additionally, strategic approaches for successful and effective programs targeting healthy weight should be based on better understanding about women's self-perceptions and motivations.

• 한국재료학회지
• /
• 제24권3호
• /
• pp.166-173
• /
• 2014

The effects of printed circuit board electroless nickel immersion gold (ENIG) and organic solderability preservative (OSP) surface finishes on the electromigration reliability and shear strength of Sn-3.5Ag Pb-free solder bump were systematically investigated. In-situ annealing tests were performed in a scanning electron microscope chamber at 130, 150, and $170^{\circ}C$ in order to investigate the growth kinetics of intermetallic compound (IMC). Electromigration lifetime and failure modes were investigated at $150^{\circ}C$ and $1.5{\times}10^5A/cm^2$, while ball shear tests and failure mode analysis were conducted under the high-speed conditions from 10 mm/s to 3000 mm/s. The activation energy of ENIG and OSP surface finishes during annealing were evaluated as 0.84 eV and 0.94 eV, respectively. The solder bumps with ENIG surface finish showed longer electromigration lifetime than OSP surface finish. Shear strengths between ENIG and OSP were similar, and the shear energies decreased with increasing shear speed. Failure analysis showed that electrical and mechanical reliabilities were very closely related to the interfacial IMC stabilities.

• Nuclear Engineering and Technology
• /
• 제54권6호
• /
• pp.2094-2106
• /
• 2022

The solid-state core of a heat pipe cooled reactor operates at high temperatures over 1000 K with thermal and irradiation-induced expansion during burnup. The expansion changes the gap thickness between the solid components and the material properties, and may even cause the gap closure, which then significantly influences the thermal and mechanical characteristics of the reactor core. This study developed an irradiation behavior model for HPRTRAN, a heat pipe reactor system analysis code, to introduce the irradiation effects such as swelling and creep. The megawatt heat pipe reactor MegaPower was chosen as an application case. The coupled irradiation-thermal-mechanical model was developed to simulate the irradiation effects on the heat transfer and stresses of the whole reactor core. The results show that the irradiation deformation effect is significant, with the irradiation-induced strains up to 2.82% for fuel and 0.30% for monolith at the end of the reactor lifetime. The peak temperatures during the lifetime are 1027:3 K for the fuel and 956:2 K for monolith. The gap closure enhances the heat transfer but caused high stresses exceeding the yield strength in the monolith.