• Journal of Radiation Protection and Research
• /
• v.24 no.2
• /
• pp.73-86
• /
• 1999

The ion-exchange method for the purification of primary coolant has been used broadly in PWR(pressurized water reactor)-type nuclear power plants due to its high decontamination efficiency, simple system, and easy operation. However, its non-selective removal of metal and non-radionuclides shortens its life, resulting in the generation of a large amount of waste ion-exchange resin. In this study, the feasibility of electrodeionization (EDI) was investigated for the purification of primary cooling water using synthetic solutions under various experimental conditions as an alternative method for the ion exchange. The results shows that as the feed flow-rate increased, the removal efficiency increased and the power consumption decreased. The removal rate was observed as a 1000 decontamination factor(DF) at a nearly constant level. For the synthetic solution of 3 ppm TDS (Total Dissolved Solid), the power consumption was 40.3 mWh/L at 2.0 L/min of feed flow rate. The higher removal rate of metal species and lower power consumption were obtained with greater resin volume per diluting compartment. However, the flow rate of the EDI process decreased with the elapsed time because of the hydrodynamic resistivity of resin itself and resin fouling by suspended solids. Thus, the ion-exchange resin was replaced by an ion-conducting spacer in order to overcome the drawback. The system equipped with the ion-conducting spacer resolved the problem of the decreasing flow rate but showed a lower efficiency in terms of the power consumption, the removal rate of metal species and current efficiency. In the repeated batch operation, it was found that the removal efficiency of metal species was stably maintained at DF 1000.

• Korean Journal of Organic Agriculture
• /
• v.20 no.4
• /
• pp.503-518
• /
• 2012

Korean type of no-tillage cultivation method which was applied on this study used the ridge and the furrow and constantly recycling them as it was suitable for Korea's weather and farming conditions. This no-tillage cultivation was reported to have little negative impact such as reduction of production (Kwon et al., 1997). In addition, it was found to have a lot of benefits as it requires less agro-materials and energy costs as well as shortened working hours because tillage operation is not needed. (Yang et al., 2012). According to an analysis, no-tillage cultivation can reduce greenhouse gas emissions by $344.7kgCO^2$ (58%) in every 10a ($1,000m^2$) compared to ordinary pepper farming technique (Korea averages). Direct-indirect reduction effects from using fertilizer and using less amount of energy were 92% and 44% respectively both of which can be considered very high. Besides the direct effects of no-tillage cultivation, soil management using no-tillage technique raises carbon sequestration effect on soil as time goes on (West & Marland, 2002), that is why the technique is expected to have constant carbon emission reduction effect. For theses reasons, distribution and expansion of Korean type no-tillage cultivation are expected to play a role as major agro-green technologies for achieving our goal of reducing greenhouse gas emissions in agricultural sector.

• Journal of Korean Academy of Nursing
• /
• v.9 no.2
• /
• pp.49-61
• /
• 1979

A review of this literature and discussions reveal a development of ideas concerning the elements of nursing models. The elements of a nursing model are the nurses view of the human being, nursing's goal, and nursing activities. It has long been recognized that human beings, at one time or another, require nursing care. Varieties of literature were reviewed in regard to the human being as recipient of nursing care through the theory development in nursing. Florence Nightingale initiated the modern era of nursing and described more clearly man as the recipient of nursing care. She looked at man as responding to the laws of nature whether the person was healthy or sick. Henderson added to Nightingale's concept of man , the recipient of nursing care by emphasizing that man is a whole, complete, and independent being. Her view is further specified by her enumeration of the activities the human being must perform. Johnson has developed a very comprehensive view of man as the recipient of nursing care. Man is a behavioral system which has a tendency to achieve and maintain stability in patterns of functioning. Like Nightingale, Johnson sees that similar patterns occur in both health and illness. Johnson postulates that the whole behavioral system of the human is composed of eight sub-systems: affiliative, achievement, aggressive, dependency, eliminative, ingestive, restorative, sexual. Roger's main contribution to the development of nursing models was her emphasis upon unitary man. She pointed out that man is a unified whole, possessing his own integrity and manifesting characteristics that“are more than and different from the sum of his parts.”Rogers focuses on the life processes of the human and points out that these processes have the following characteristics. Wholeness, openness, unidirectionality, pattern and organization, sentence, and thought. According to Roy, man is a biopsychosocial being in constant interaction with a changing environment. To cope with this changing environment, man has certain innate and acquired mechanisms. Man's ability to respond positively or to adapt, depends upon the degree of the change taking place and the state of the person coping with the change. When she analyzes man as an adaptive organism she further describes man as being composed of four adaptive modes: physiological needs, self-concept, role function, and interdependence. Based on the literary review through the theory development in nursing, general approach by a unified nursing model to a view of the recipient of nursing care may be stated as follows: Man is a unified whole composed of subsystems with a flexible and normal line of defense; his internal regulating mechanisms help him to cope with a changing environment; he functions by the principles of homeodynamics.

• Journal of Digital Convergence
• /
• v.17 no.12
• /
• pp.393-398
• /
• 2019

This study aimed to suggest the optimum number of rinsing by researching changes in optical density and pH in accordance with the number of rinsing after toothbrushing, and then verifying the amount of residual toothpaste in mouth. Total 14 university students who had healthy body with no difficulties in daily life were selected from the students of K university in Daegu as the research subjects. The research subjects rinsed their mouths with 40ml of water from zero time to 12 times after toothbrushing. After collecting each rinsing water, the optical density and pH were measured. In the results of measuring the optical density value of each rinsing water, the rinsing water of six-seven times or more after toothbrushing showed the constant value of optical density, which was statistically significant(p<0.05). There were no differences in accordance with the amount of toothpaste such as 1g, 1.5g, and 2g. Based on such results of this study, it would be necessary to provide the education of the use of dentifrice, and also to have diverse researches on the effects of residual dentifrice in mouth on the oral cavity.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.3
• /
• pp.195-203
• /
• 2012

In this study, The effects of three different biological activated carbon (BAC) materials (each coal, coconut and wood based activated carbons) and anthracite, empty bed contact time (EBCT) and water temperature on the removal of MK, HHCB and AHTN in BAC filters were investigated. Experiments were conducted at three water temperatures (5, 15 and $25^{\circ}C$) and four EBCTs (5, 10, 15 and 20 min). The results indicated that coal based BAC retained more attached bacterial biomass on the surface of the activated carbon than the other BAC, increasing EBCT or increasing water temperature increased the synthetic musk compounds (SMCs) removal in BAC columns. The kinetic analysis suggested a first-order reaction model for MK, HHCB and AHTN removal at various water temperatures (5, 15 and $25^{\circ}C$). The pseudo-first-order biodegradation rate constants and half-lives were also calculated for MK, HHCB and AHTN removal at 5, 15 and $25^{\circ}C$. The pseudo-first-order biodegradation rate constants and half-lives of MK, HHCB and AHTN ranging from 0.0082 $min^{-1}$ to 0.4452 $min^{-1}$ and from 1.56 min to 84.51 min could be used to assist water utilities in designing and operating BAC filters for SMCs removal.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.3
• /
• pp.278-284
• /
• 2016

Software reliability in the software development process is an important issue. In infinite failure NHPP software reliability models, the fault occurrence rates may have constant, monotonic increasing or monotonic decreasing pattern. In this paper, infinite failures NHPP models that the situation was reflected for the fault occurs in the repair time, were presented about comparing property. Commonly, the software model of the infinite failures using the linear hazard rate distribution software reliability based on intercept parameter was used in business economics and actuarial modeling, was presented for comparison problem. The result is that a relatively large intercept parameter was appeared effectively form. The parameters estimation using maximum likelihood estimation was conducted and model selection was performed using the mean square error and the coefficient of determination. The linear hazard rate distribution model is also efficient in terms of reliability because it (the coefficient of determination is 90% or more) in the field of the conventional model can be used as an alternative model could be confirmed. From this paper, the software developers have to consider intercept parameter of life distribution by prior knowledge of the software to identify failure modes which can be able to help.

• Journal of Distribution Science
• /
• v.12 no.8
• /
• pp.5-15
• /
• 2014

Purpose - The method of TV home shopping is a kind of retail method that provides the viewer with information about products and, further, sells the products to consumers through the media of television. The domestic home-shopping industry has been expanding since 1995, and there are six companies in this arena as of 2012. In this study, we evaluate the management efficiency of TV home-shopping companies and provide suggestions for improving efficiency, using the DEA (data envelopment analysis) model. Hence, we expect to contribute to the progress of the companies' efficiency and the development of the TV home-shopping industry, where deepening competition is inevitable because it is experiencing the maturing market stage in its life cycle. Research design, data, and methodology - Efficiency is the ratio of the quantity of input to the quantity of output of a product or service. It is necessary to estimate aggregate inputs and aggregate outputs, which are calculated by applying a weighting to a number of input and output factors, to measure the efficiency. The DEA model is divided into the CCR model and the BCC model. The CCR model is a basic model that assumed constant returns to scale (CRS), and the BCC model extends the CCR model to accommodate technologies exhibiting variable returns to scale (VRS), and concerns only the technical efficiency without considering the efficiency of returns to scale. In this study, we consider six companies each year from 2008 to 2012 as a DMU (Decision Making Unit) and analyze the differences in efficiency for each company in each year. Furthermore, we evaluate the operating characteristics of TV home-shopping companies, using three models, in accordance with the overall performance, profitability, and marketability of the business. Results - The result of the analysis, using DEA models, shows that Hyundai Home Shopping (2009, 2010, 2011), GS Home Shopping (2011), NS Home Shopping (2011) and CJ O Shopping (2012) possess MPSS (most productive scale size), with a score 1.0 in CCR, BCC, and scale efficiency. Particularly, Hyundai Home Shopping is shown to be the most efficient in terms of overall business performance, marketability, and profitability. The overall efficiency of the home shopping industry has displayed an increasing trend since 2008, even though it decreased marginally in 2012; further, we can observe that home shopping companies operate with increasing efficiency with the passage of time. Conclusions - Home shopping companies have focused on market expansion rather than profits, as they displayed better efficiency in marketability than increase in profitability during the period 2008-2012. In addition, the main reason for the increased efficiency in the home shopping industry is the market expansion through the revenue increase of each home shopping company. This study can be used as a reference when home shopping companies attempt to devise future strategies, as it suggests efficiency benchmarks and development levels for each home shopping company.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.6
• /
• pp.1063-1070
• /
• 2011

In this study, total of 5 different chemical amendments were evaluated for determining kinetic parameters and stabilization efficiency of heavy metals in aqueous phase. Standard solution of Cd and Pb ($100mg\;L^{-1}$) was mixed with various ratio of amendments (1, 3, 5, 10%) and heavy metal stabilization efficiency was monitored for 24hrs. All examined amendments showed over 90% of removal efficiency for both Cd and Pb except zerovalent iron (ZVI) for Cd (43-63%). Based on result of heavy metal stabilization efficiency, it was ordered as $CaCO_3$ > Dolomite > Zeolite > Steel slag > ZVI for both Cd and Pb in aqueous phase. For kinetic study, first order kinetic model was adapted to calculate kinetic parameters. In terms of reaction rate constants (k), zeolite showed the fastest reaction rate (k value from 0.4882 for 1% to 2.0105 for 10%) for Cd and ZVI (k value from 0.2304 for 1% to 0.5575 for 10%) for Pb. Considering reaction rate constant and half life for heavy metal stabilization, it was ordered as Zeolite > $CaCO_3$ > Dolomite > Steel slag > ZVI for Cd and $CaCO_3$ > Dolomite > Steel slag > Zeolite > ZVI for Pb. Overall result in this study can be interpreted that lime containing materials are more beneficial to remove heavy metals with high efficiency and less time consuming than absorbent materials.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.25 no.4
• /
• pp.163-180
• /
• 2022

Real estate data can be big data. Because the amount of real estate data is growing rapidly and real estate data interacts with various fields such as the economy, law, and crowd psychology, yet is structured with complex data layers. The existing Relational Database tends to show difficulty in handling various relationships for managing real estate big data, because it has a fixed schema and is only vertically extendable. In order to improve such limitations, this study constructs the real estate data in a Graph Database and verifies its usefulness. For the research method, we modeled various real estate data on MySQL, one of the most widely used Relational Databases, and Neo4j, one of the most widely used Graph Databases. Then, we collected real estate questions used in real life and selected 9 different questions to compare the query times on each Database. As a result, Neo4j showed constant performance even in queries with multiple JOIN statements with inferences to various relationships, whereas MySQL showed a rapid increase in its performance. According to this result, we have found out that a Graph Database such as Neo4j is more efficient for real estate big data with various relationships. We expect to use the real estate Graph Database in predicting real estate price factors and inquiring AI speakers for real estate.

• Korean journal of applied entomology
• /
• v.24 no.4 s.65
• /
• pp.195-201
• /
• 1986

This study was conducted to investigate the life history of Compsidia populnea which is major species of the stem-borers on Populus alba{\times}glandulosa$. Peak emergence of the adult of Compsidia populnea L. was around 10th${\sim}$l2nd of May in Chuncheon vicinities, having one generation a year in Korea. There was a preovipositional period of 10.7 days and a ovipositional period of 14.3.days. Mean adult longevity was 11 days for male and 13.8 days for female. Individual eggs were long oval with somewhat narrowed tip at one side and soft, 2.6mm in length, 0.8mm in diameter, and were laid singly under the U-shaped scars which were made by female before oviposition. Total number of scars per female averaged 56.6 ($8{\sim}135$) and eggs were found in 67.9 percent of the total scars. Egg period was $8{\sim}11$ days at $25^{\circ}C$ constant temperature and $7{\sim}14$ days in the field condition. Early young larvae stayed for $2{\sim}3$ weeks under the scars and then boring into the xylem, forming galls at this time. Size of the gall was 1.8cm($1.3{\sim}2.5$) in length, 1.6cm($1.0{\sim}2.2$) in diameter and the length of mine was everage 3.1cm. Fully grown larvae were developed around the early October and overwintered in the mines of galls. Pupation was done around the early of April. Pupal developmental period averaged 11 days($9{\sim}13$ days) at $25^{\circ}C$ constant temperature condition.