• Journal of Korean Neurosurgical Society
• /
• v.38 no.3
• /
• pp.227-230
• /
• 2005

Hearing loss in the contralateral functioning ear is a rare and distressing complication after vetibular schwannoma removal. Various possible mechanisms have been proposed, however, the etiology of hearing loss is not clear. Fortunately, this is an extremely rare occurrence, sporadic case reports have appeared in the literatures. We report two cases of acute contralateral hearing loss after vestibular schwannoma removal and discuss the possible mechanisms of the phenomenon. Although permanent deafness may result, in our cases, the hearing loss was temporary, returning to near preoperative level within one month. The etiology of hearing loss in one case is thought to be cerebrospinal fluid leakage. However, in the other case, the cause of hearing loss is not clear. A better understanding of these events may lead to preventive measures to avoid contralateral hearing loss after vestibular schwannoma removal.

• Tribology and Lubricants
• /
• v.21 no.5
• /
• pp.227-235
• /
• 2005

This paper presents a tribological study on the failure cases of automatic transmission components in a passenger car. The automatic transmission system is composed of torque converter, clutch, brake, planetary gear, and valve body controlling oil pressure of an automatic transmission fluid. The most largest influence components in an automatic transmission are a torque converter and clutch plate in which are influenced by a wear and torque converting energy loss. The failure case study of an automatic transmission indicates that the tribological design and maintenance technologies should be considered as a key design concept. This means that the failure and power energy loss come from the friction, wear and a oil leakage of an automatic transmission, which is related to the oil seal and O-ring seal failures.

• The KSFM Journal of Fluid Machinery
• /
• v.16 no.2
• /
• pp.15-20
• /
• 2013

An aero-acoustic performance analysis method of regenerative blower is developed as one of the FANDAS codes. The aerodynamic performance of regenerative blower is predicted by using momentum exchange theory coupled with pressure loss and leakage flow models. Based on the performance prediction results, the noise level and spectrum of regenerative blower are predicted by discrete frequency and broadband noise models. The combination of the performance and the noise prediction methods gives aero-acoustic performance map and noise spectrum analysis results, which are well-agreed with the actual measurement results within a few percent relative error.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1465-1468
• /
• 1997

In this study we investigated the aging characteristic such as leakage current, dielectric loss, contact angle, of EPDM for outdoor use by thermal treatment. And also observed the color change of surface, changing of chemical ingredient of the marterials by optical microscope. SEMI, FTIR and EDX at the section and surface. The test result show that leakage current is increased with thermal aging time. contact angle and dielectric loss is slightly decreased. Moreover, micro-void or crack in bulk is severely increased with aging time. However, the result affect to the tan $\delta$ at bulk of EPDM. It seems that carrier sources are removed by degassing with heat treatment.

• Journal of the Korean Society of Combustion
• /
• v.16 no.1
• /
• pp.46-51
• /
• 2011

Exhaust gas of an industrial furnace used at such as metallurgy or ceramic manufacturing usually contains thermal energy with high temperature which can be recycled by heat exchanger. However, when the temperature of the exhaust gas is high such as more than $1,000^{\circ}C$, ordinary metallic heat exchanger cannot fully recover the heat due to the limitation of operating temperature depending on the material property. In the present study, a compact ceramic heat exchanger of cross flow type is introduced and evaluated by heat exchange rate and operating temperature. The ceramic heat exchanger can endure the gas temperature more than $1,300^{\circ}C$, and its volumetric heat exchanging rate exceeds 1 MW/$m^3$. The experimental data is also compared with the previous numerical result which shows reasonable agreement. Meanwhile, the gas leakage rate is measured to be about 3~4%, and heat loss to environmental air is about 23~26% of the fuel energy.

• Electrical & Electronic Materials
• /
• v.9 no.4
• /
• pp.344-350
• /
• 1996

Tracking is one of the biggist problems to be overcome in polymeric materials for outdoor insulators. But It can be decreased with the addition of filler such as alumina trihydrate (ATH). In this paper, the tracking of surface and evaluation of insulating ability at silicone rubber is investigated, using the salt fog test. At initial state, the peak leakage current and numbers by dry band arcing is increasing with increasing the filler level, but at aged state decreasing at high concentration filler samples. This is because the roughness of the surface may contribute to the increase in peak leakage cur-rent and numbers. As increasing the filler level, the insulating ability of materials is higher and weight loss is decreased. The mechanism of insulating failure is occurred by the erosion than the tracking and the erosion caused weight loss of 2 g.

• The KSFM Journal of Fluid Machinery
• /
• v.5 no.2 s.15
• /
• pp.7-14
• /
• 2002

The effect of tip clearance is important part for turbomachinery performance. Tip leakage flow due to tip clearance is mixed with passage vortex. Large amount of loss is generated at the mixing region and overall performance of turbomachinery is reduced. Numerical calculation of the 1st stage rotor of GE7FA gas turbine is carried out to investigate tip clearance effect on performance, pitchwise variations of velocity profiles, pressure distributions and loss coefficients. A commercial code, CFX-TascFlow is validated in this study.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.3
• /
• pp.113-119
• /
• 1998

In this paper, the error sidelobe level and signal to noise loss from the numerical analysis using the modelling of quadrature coherent detector in the case that the channel imbalance and with local oscillator leakage is considered. From the numerical results, the error sidelobe level and signal to noise loss that with the gain and phase imbalance(0.8(dB)J5(dog)) is (-21.322[dB], -0.0071[dB]), (-11.6839[dB], -0.0059[dB]) in the case that the channel imbalance and with local oscillator leakage is considered.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.894-904
• /
• 2016

This study examines the zero-voltage switching (ZVS) operation of an active-clamped forward converter (ACFC) with a current-doubler rectifier (CDR). The ZVS condition can be obtained with a much smaller leakage inductance compared to that of a conventional ACFC. Due to the significantly reduced leakage inductance, the design is optimized and the circulating loss is reduced. The operation of the ACFC with a CDR is analyzed, and a detailed ZVS analysis is conducted on the basis of a steady-state analysis. From the results, a design consideration for ZVS improvement is presented. Loss analyses of the converters shows that enhanced soft-switching contributes to an efficiency improvement under light-load condition. Experimental results from a 100-W (5-V/20-A) prototype verify that the ACFC with a CDR can attain ZVS across an extended load range of loads and achieve a higher efficiency than conventional ACFCs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.505-508
• /
• 1999

In this study, weight loss, ESDD, surface conductivity and leakage current were measured at the different saline solutions by salt fog method. The magnitude of leakage current was higher at higher conductivity of 2 S/m saline water, but weight loss ESDD and surface conductivity which are indices of degradation were lower. This is considered that the current includes mainly ohmic component which doesn\`t contribute to surface degradation. In addition, it is shown that FFT could be useful in measuring initial transition from hydrophobic to hydrophilic surface.