• 수산해양기술연구
• /
• 제27권2호
• /
• pp.120-124
• /
• 1991

이상의 결과를 정리하면 다음과 같이 요약할 수 있다. (1)Karman의 적분 방정식에 미소 거칠기 영향을 고려함으로서 디퓨져 닥트 표면의 경계층 계산에 응용한 결과 모멘트 적분법 및 실험치와의 비교에서 개선된 결과임이 확인되었다. (2) 국소 거칠기의 효과를 주는 방법으로는 Cole의 벽 및 와 법칙에 Clauser의 거칠기 함수와, 압력 기울기를 고려한 부가 형상계수 값으로 적분 방정식에 응용할 수 있다. (3) 국소 거칠기 분포에 의하여 경계층 특성을 교란시켜 표면 마찰력 계수를 줄일 수 있어 마찰력 손실을 줄일 수 있는 방안이 제시되었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.294-297
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. Higher friction coefficient was obtained at harder coating with rougher surface. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with indentation hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics after nano scratching more than indentation hardness.

• Tribology and Lubricants
• /
• 제24권2호
• /
• pp.96-103
• /
• 2008

PTFE is generally utilized as the form of composites with adding various fillers. The purpose of this paper lies on clarifying the friction and wear properties of the PTFE coating layer on steel. Especially, the effects of PTFE powder size for coating and surface roughness of the counter material on the properties are investigated. Sliding friction and wear tests are conducted at several sliding speeds by employing two types of PTFE coating layer using different powder sizes. One type of coating layer is composed of uniform fine powder, whereas the other type is made up of mixture powder of different sizes. As results, it is found that PTFE coating layer are effective to improve the wear resistance and to reduce the friction coefficient. It is clear that PTFE coating layers are abrasively removed by asperities of the counter material during sliding contact. However, PTFE coating layer with uniform fine powder shows somewhat better wear resistance than that with mixture powder of different sizes in low sliding speed region. It can be seen that the wear of the coating layer are drastically reduced because wear fragment from counter material are transferred to the coating layer. On the other hand, friction coefficient is shown not to be directly related with PTFE powder size in coating layer.

• 설비공학논문집
• /
• 제13권12호
• /
• pp.1282-1287
• /
• 2001

This study presents the numerical analysis of natural convection of a micro- environments with air permeability in the clothing air-layer. As a numerical model the clothing air layer of shoulder and arm were adopted. Finite volume method for two-dimensional laminar flow was used for the analysis of flow and thermal characteristics of velocity, temperature and concentration in the air layer between body and clothing. As temperature boundary conditions, a body skin has a high temperature with $34^{\circ}C$ and the environmental temperatures are 5, 15 and $25^{\circ}C$ for various permeability coefficients. The distributions of concentration, temperature and velocity are shown that two large cells form at horizontal and vertical air layer, respectively. As the temperature difference between body skin and environment decreases, the heat transfer is decreased rapidly.

• 한국도로학회논문집
• /
• 제17권1호
• /
• pp.51-58
• /
• 2015

PURPOSES : The objective of this study is to compare the densities of asphalt pavements measured both in the field and in the laboratory, and also to evaluate the applicability of field density measuring equipment, such as the pavement quality indicator (PQI), by using statistical analysis. METHODS : For the statistical analysis of the density measured from asphalt pavement, student t-tests and a coefficient of correlation are investigated. In order to compare the measured densities, two test sections are prepared, with a base layer and an intermediate layer constructed. Each test section consists of 9 smaller sections. During construction, the field densities are measured for both layers (base and intermediate) in each section. Core samples are extracted from similar regions in each section, and moved to the laboratory for density measurements. All the measured densities from both the field and laboratory observations are analyzed using the selected statistical analysis methods. RESULTS AND CONCLUSION : Based on an analysis of measured densities, analysis using a correlation coefficient is found to be more accurate than analysis using a student t-test. The correlation coefficient (R) between the field density and the core density is found to be very low with a confidence interval less than 0.5. This may be the result of inappropriate calibration of the measuring equipment. Additionally, the correlation coefficient for the base layer is higher than for the intermediate layer. Finally, we observe that prior to using the density measuring equipment in the field, a calibration process should be performed to ensure the reliability of measured field densities.

• 한국추진공학회지
• /
• 제16권3호
• /
• pp.82-89
• /
• 2012

추진제탱크 내의 극저온 추진제는 발사체의 비행 과정동안 주변으로부터 에너지를 흡수하여 온도가 상승한다. 비행 종료 시점에 있어 터보펌프 입구 요구조건 이상으로 온도가 상승된 추진제는 사용할 수 없는 잔류추진제로 남게 된다. 본 논문에서는 극저온 추진제 상층부의 온도변화를 살펴보기 위하여 추진제 표면 근처에서의 열전달계수를 구해보고자 하였다. 추진제 상층부의 열전달을 전도로 단순화하여 열전달계수를 예측하는 방법을 제시하였다. 이를 통해 얻어진 추진제 상층부의 온도를 시험데이터와 비교하여 열전달계수 예측 방법의 적용 가능성을 확인하였다.

• 소성∙가공
• /
• 제14권8호통권80호
• /
• pp.696-703
• /
• 2005

In the modern days, a galvannealed sheet steel (GA) instead of a cold rolled steel sheet has been widely used as an alternative to extend the life of automotive body. Accordingly, the mechanical properties of GA for automobiles were taken into account and studied by examining their variation with annealing temperature. To clarify the effect of surface features on the mechanical and frictional properties of GA, the several tests such as nanoindentation, Vickers hardness and nano scratch test were executed. The frictional characteristics of coating layers of GA were examined through nano scratch test in this study. The friction coefficient of coating layers on the surface was obtained from the nano scratch. The variation of friction coefficient versus velocity and pressure was taken into consideration in this paper. Hardness and elastic modulus of coating layer were increased as increasing annealing temperature.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.709-716
• /
• 2011

추진제탱크 내의 극저온 추진제는 발사체의 비행 과정동안 주변으로부터 에너지를 흡수하여 온도가 상승한다. 비행 종료 시점에 있어 터보펌프 입구 요구조건 이상으로 온도가 상승된 추진제는 사용할 수 없는 잔류추진제로 남게 된다. 본 논문에서는 극저온 추진제 상층부의 온도변화를 살펴보기 위하여 추진제 표면 근처에서의 열전달계수를 구해보고자 하였다. 추진제 상층부의 열전달을 전도로 단순화하여 열전달계수를 예측하는 방법을 제시하였다. 이를 통해 얻어진 추진제 상층부의 온도를 시험데이터와 비교하여 열전달계수 예측 방법의 적용 가능성을 확인하였다.

• 대한기계학회논문집B
• /
• 제25권8호
• /
• pp.1131-1139
• /
• 2001

Experimental results are presented, which describe the effect of blowing ratio on film cooling from two rows of holes with opposite orientation angles. The inclination angle is fixed at 35°, and the orientation angles are set to be 45°for the downstream row, and -45°for the upstream row. The studied blowing ratios are 0.5, 1.0 and 2.0. The boundary layer temperature distributions are measured using thermocouple at two downstream locations. Detailed adiabatic film cooling effectiveness and heat transfer coefficient distributions are measured with TLC(Thermochromic Liquid Crystal). The adiabatic film cooling effectiveness and heat transfer coefficient distributions are discussed in connection with the injectant behaviors inferred from the boundary layer temperature distributions. Film cooling performance, represented by heat flux is evaluated from the adiabatic film cooling effectiveness and heat transfer coefficient data. The results show that the investigated geometry provides improved film cooling performance at the high blowing ratios of 1.0 and 2.0.

• 소성∙가공
• /
• 제18권6호
• /
• pp.465-470
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. The effect of surface roughness of cylinder liner on the friction coefficient was analyzed. This study provided tribological data of hard and soft piston ring coatings against cylinder liner. The surface roughness does exert an influence on the average friction coefficient, with smoother surfaces generally yielding lower friction coefficients. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics such as, scratch depth, width, pile-up height and elastic modulus.