• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.123-130
• /
• 2008

Flight safety analysis, which includes risk estimation for the various abnormal flight modes in addition to normal flight, has to be performed necessarily to guarantee launch safety for the operation of space launch vehicles. For this purpose, a dedicated system has been developed such that all the necessary repetitive computations, result reports, and graphical presentations can be performed inside a single system for user convenience. In addition, the developed system is capable of representing computed results on a three dimensional Earth for the realistic presentation. The developed Flight Safety Analysis System will be employed for the launch operation of Korea Satellite Launch Vehicle-I.

• 시스템엔지니어링워크숍
• /
• s.4
• /
• pp.90-94
• /
• 2004

System engineering(SE) management techniques applied for space launch system development are introduced to assess the current status and address the effwctiveness of these techniques. Management plans and guides are prepared for the work breakdown structure , data, comfiguration, interface control, Quality assurance, procurement, reliability, risk and verification/validation . Further improvement is required for the system engineering management plan(SEMP) to merge the international cooperation into current engineering managment system.

• Aerospace Engineering and Technology
• /
• v.2 no.1
• /
• pp.140-152
• /
• 2003

Scenario is a guiding principle of launch operation and control for rocket and ground support system. Therefore, developing a scenario is the first step to prepare for rocket launch, which is a critical task for success of KSR-III flight test. The launch scenario for KSR-III flight test is a procedural sequence of command and control signals to be given to rocket and ground support systems. In this paper, the UML object modeling method is applied to development of a launch scenario. First, the subsystems of the launch system are modeled by objects, and then the interfaces between each two subsystems are modeled by association links. The finally obtained object diagram of KSR-III launch system is used to analyzing flow of data and commands and control signals, and interactions. The scenario includes the sequences of pre-launch/launch operations and emergency operations.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.8
• /
• pp.657-665
• /
• 2016

Launch Control System(LCS) performs the pre-launch preparation and launch operation during launch campaign. The successful launch operation is basically influenced by hardware and software of LCS. Especially, a trivial errors in control algorithm can cause critical problem or disaster in launch operation. Therefore, the hidden or implicit errors should be distinguished and eliminated by the verification test in advance. In this paper, the design and implementation of hardware and software simulator which have already been used in LCS verification will be introduced. By presenting the detailed design and flowchart-based algorithms, we make other similar systems adopt the implementation philosophies of this paper. Especially, this paper emphasizes that all the simulation algorithms work on the self-controller in LCS without using separated computer or PLC.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.6
• /
• pp.567-572
• /
• 2009

The underwater launch system using an ATP consists of five parts: compressor tank, proportional flow control servo valve, expulsion spool valve, air turbine pump, and discharge tube. The purpose of this study is to develop an underwater launch system using an ATP and to verify the validity of the system. The proportional flow control servo valve is modeled as a 2nd order transfer function. The projectile is ejected by pressurized water through the air turbine pump, which is controlled by expulsion valve. The mathematical model is derived to estimate the dynamic characteristics of the system, and the important design parameters are derived by using simulations. The computer simulation results show the dynamic characteristics and the possibility of control for underwater launch system.

• Aerospace Engineering and Technology
• /
• v.11 no.2
• /
• pp.103-108
• /
• 2012

There is close correlation between the reliability of the launch vehicle and the leakage of the propellants or gases from the launch vehicle. This paper describes the definition of the leak rate to determine the quantity of the leakage and introduce the unit conversion of the leak rate. The main parameters for the leak rate were considered. The requirements for the gaseous for the leak test of launch vehicle and various leak test methods were introduced. Leak test method and procedure used in space launch vehicle were briefly described.

• Journal of Aerospace System Engineering
• /
• v.10 no.4
• /
• pp.35-40
• /
• 2016

Mid-course correction maneuvers (MCCMs) are necessary to correct the launch-vehicle dispersion to go to the Moon. There were 3 or 4 MCCMs needed for a direct transfer trajectory. But the strategy for MCCMs of the phasing-loop trajectory is different, because it has a longer trans-lunar trajectory than direct transfer does. An orbiter using a phasing-loop trajectory has several rotations of the Earth, so the orbiter has several good places, such as perigee and apogee, to correct the launch-vehicle dispersion. Although launch dispersion is relatively high, the launch vehicle is not as accurate as we expected. A good MCCM strategy can overcome the high dispersion by using small-magnitude correction maneuvers. This paper describes the phasing-loops sequence and strategy to correct high launch-vehicle dispersions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.7
• /
• pp.517-524
• /
• 2014

Micro-vibration induced by on-board equipments such as fly-wheel and cryogenic cooler with mechanical moving parts affects the image quality of high-resolution observation satellite. Micro-vibration isolation system has been widely used for enhancing the pointing performance of observation satellites. In general, the micro-vibration isolation system requires a launch locking mechanism additionally to guarantee the structural safety of mission payloads supported by the isolation system with low stiffness under launch environment. In this study, we propose a passive launch and on-orbit vibration isolation system using shape memory alloy mesh washers for the micro-vibration isolation of spaceborne compressor, which does not require the additional launch locking mechanism. The basic characteristics of the isolator were measured in static and free vibration tests of the isolator, and a simple equivalent model of the isolator was proposed. The effectiveness of the isolator design in a launch environment was demonstrated through sine vibration, random vibration and shock tests.

• Journal of Korean Society for Quality Management
• /
• v.50 no.3
• /
• pp.533-543
• /
• 2022

Purpose: The purpose of this study is to identify and resolve the causes of defects in the unmanned aerial vehicle launch system(propulsion wire fracture, rear rail deformation) and to prevent recurrence. Methods: The causes of the two defects were derived through fault tree analysis for each of the two defects and fault reproduction tests. In the case of propulsion wire, the installation of a high speed camera to check the behavior of wire was the driving force behind the defect resolution. Results: The results of this study are as follows; It was determined that the thickness of the washer was less than the maximum tolerance of the pulley was the cause of the propulsion wire fracture defect. Failure to comply with the launch procedure and insufficient safety margin were judged as the cause of the rear rail deformation defect. Accordingly, the configuration was changed to remove each defect. Conclusion: The case of this study was conducted to eliminate defects in the launch system for UAV. The causes of defects were estimated through fault tree analysis. After the configuration change, Structural analysis and launch tests were performed to demonstrate the safety and effectiveness of the modified configuration. As a result, the effect of the modified configuration was verified.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.99-105
• /
• 2006

A Launch vehicle which consists of many sub-systems is one sophisticated huge system. A lot of experience and system integration technique are needed for the launch vehicle to accomplish a mission successfully. The characteristics and complexity in the development of the launch vehicle depend on the size of that. However the systematic work flow is similar to each other. This paper introduces a standardized development process which is based on the whole program life cycles and experiences of NASA on the development of the launch vehicle. The development process can be categorized into 10 phases through the life cycle of the launch vehicle.