• Journal of Welding and Joining
• /
• v.15 no.4
• /
• pp.99-108
• /
• 1997

Analytical model for the temperature distribution and the cooling rate of weld in dual beam laser welding is presented for investigating the possibility of controling the cooling rate. The model is based on the solutions to the problem of heat flow due to the distributed and line heat sources for preheating and welding respectively in plates with finite thickness. The effects of beam power, beam distribution parameter, interbeam distance, and welding speed on the resulting temperature distribution and cooling rate are presented. The cooling rates of dual beam laser weld at the weld centerline under the investigated conditions are reduced to as one third of those of welds which were produced by single beam laser. And it appeared that the cooling rate of dual beam laser weld is strongly dependent on the process parameters of preheating laser beam power and welding speed.

• Laser Solutions
• /
• v.3 no.2
• /
• pp.53-61
• /
• 2000

On the laser weld production line, a slight alteration of the welding condition produces many defects. The defects are monitored in real time, in order to prevent continuous occurrence of defects, reduce the loss of material, and guarantee good quality. The measurement system is produced by using three photo-diodes for detection of the plasma and spatter signal in CO$_2$ laser welding. For high speed CO$_2$ laser welding, laser tailored welded blanks for example, on-line weld quality monitoring system was developed by using fuzzy multi-feature pattern recognition. Weld qualities were classified optimal heat input, a little low heat input, low heat input, and focus misalignment, and final weld quality were classified good and bad.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2002.05a
• /
• pp.25-27
• /
• 2002

Most of automotive companies make use of spot welding in order to assemble car body. Even though spot welding has been developed for last 60 years, there were some limitations in upgrading production line. Laser welding has advantages In productivity and degree of freedom in design. Thanks to fast speed, we can reduce body assembly line by 80%. Also with non-contact & one-side approach, it is possible to design various car body structures. New project launched the laser welding technology in mass production has started in 1999. In this paper, a new type of cur named 'next generation vehicle (NGV)' is introduced. The car body of NGV is welded with 4㎾ Nd: YAG laser.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2006.06a
• /
• pp.97-100
• /
• 2006

Picosecond (ps) laser micro-machining has emerged as an attractive method of fabricating high-precision microstructures, especially in metals. In this paper, a metallic mold for diffraction gratings is fabricated with a mode-locked 12 ps $Nd:YVO_4$ laser. Laser pulses with a wavelength of 355nm are irradiated on the surface of NOK 80, a mold material, to generate line patterns. In order to minimize the line width, laser power is set just above the ablation threshold of NOK 80. Results show that the spectrum from the fabricated mold is good enough for some industrial application.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.4
• /
• pp.31-36
• /
• 2009

In this paper, the laser cutting characteristics of the flexible PCB using high power Nd:YAG UV laser were investigated. A specific FPCB model was selected for the experiment. Test sheets were made, which had equal materials and layer structure to those of the outline (OL) region and the contact pad (CP) region in the FPCB. The experiment is made up of two stages. In the first stage of the experiment, the laser cutting fluence was found, which is the threshold fluence to cut the test sheets completely. The laser cutting fluence of the OL sheet is $1781.26{\sim}1970.16\;J/cm^2$ and that of the CP sheet is $2109.34{\sim}2134.34\;J/cm^2$. In the second stage, cutting performance and its qualities were analyzed by the experiment. The laser cutting performance remained almost unchanged for all laser and process parameter sets. The average cutting width (top side/bottom side) of the OL sheet was $40.45\;{\mu}m/11.52\;{\mu}m$ and that of the CP sheet was $22.14\;{\mu}m/10.93\;{\mu}m$. However, the laser cutting qualities were different according to the parameters. The adjacent region of the cutting line on the OL sheet was carbonized as the beam speed was low and the overlap coefficient was high. The surface quality around the cutting line of the CP sheet was about the same. Carbonization and debris occurred on the surface of the cutting line. As a result of the experiment, the cutting qualities were better as the overlap coefficient was made low and beam speed high. Therefore, the overlap coefficient 2 or 3 is proper for the FPCB laser cutting.

• Journal of Acupuncture Research
• /
• v.22 no.5
• /
• pp.121-132
• /
• 2005

Objectives : The purpose of study was to compare and analyze the effect of the Intravascular Laser Irradiation Therapy and the Exterior vascular Laser Irradiation Therapy on Hypercholesterolemia. Methods : The 73 Sam-se-han-bang hospital patients who were irradiated to the Intravascular Laser and the 57 Sam-se-han-bang hospital patients who were irradiated to the Exterior vascular Laser were the study group. They had the treatment two or three times a week, and had checked total cholesterol before and after the ten times irradiation therapy. Results : Both the Intravascular Laser Irradiation Therapy and the Exterior vascular Laser Irradiation Therapy were effective on decreasing total cholesterol. The effect on decreasing total cholesterol was more definite at the abnormal group than the border line group, and the border line group than the normal group. The effect on decreasing total cholesterol was more definite at the Exterior vascular Laser Irradiation Therapy than the Intravascular Laser Irradiation Therapy, but this result was unavailable in the statistics. Conclusion : Both the Intravascular Laser Irradiation Therapy and the Exterior vascular Laser Irradiation Therapy had available effect on decreasing total cholesterol.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.41-45
• /
• 2006

The fabrication process of fiber placement system of carbon fiber reinforced plastic (CFRP) requires real time process control and reliable inspection to ensure quality by preventing defects such as delamination and void. Therefore, novel non-contact inspection technique is required during the non-destructive evaluation in a fiber placement system. For the inspection of delamination in CFRP, various methods to receive laser-generated ultrasound were applied by using piezoelectric transducer, air-coupled transducer, wavelet transform and scanning laser ultrasonic technique. Laser-generated ultrasound was received with a conventional piezoelectric sensor in contacting manner. Then signal characteristics due to defects were analyzed to find a factor for detecting defects. Air-coupled transducer was used for reception of laser-generated guided wave using linear slit array in order to generate high frequency guided wave. And line scan technique was used to confirm the capability of on-line application. The high frequency component of laser-generated guided wave received with piezoelectric sensor disappeared after propagating through delamination region. Nevertheless, it was failed to receive high frequency guided wave in using air-coupled transducer. The first peak of the frequency spectrum under 100kHz in the delamination region is higher than in the sound region. By using this feature, the line scanned frequency data were acquired in fully non-contact generation and reception of ultrasound. This method was proved as useful technique for detecting delamination in CFRP.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2001.11a
• /
• pp.29-32
• /
• 2001

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2003.05a
• /
• pp.35-38
• /
• 2003

• Journal of Mechanical Science and Technology
• /
• v.19 no.10
• /
• pp.1856-1863
• /
• 2005

In this study, a visual sensor system for weld seam tracking the I-butt weld joints in GMA welding was constructed. The sensor system consists of a CCD camera, a diode laser with a cylindrical lens and a band-pass-filter to overcome the degrading of image due to spatters and arc light. In order to obtain the enhanced image, quantitative relationship between laser intensity and iris opening was investigated. Throughout the repeated experiments, the shutter speed was set at 1/1000 second for minimizing the effect of spatters on the image, and therefore the image without the spatter traces could be obtained. Region of interest was defined from the entire image and gray level of the searched laser stripe was compared to that of weld line. The differences between these gray levels lead to spot the position of weld joint using central difference method. The results showed that, as long as weld line is within $\pm15^{o}$ from the longitudinal straight line, the system constructed in this study could track the weld line successfully. Since the processing time is no longer than 0.05 sec, it is expected that the developed method could be adopted to high speed welding such as laser welding.