• 대한기계학회논문집B
• /
• 제20권9호
• /
• pp.2991-3006
• /
• 1996

An experimental study of jet flow and heat transfer has been carried out for the jet impingement cooling on a semi-circular concave surface. For the jet impingement on the concave surface, three different regions-free jet region, stagnation region, and wall jet flow region-exist, and the distributions of mean velocity and fluctuating velocity for each region have been measured by Laser Doppler Velocimeter. Of particular interests are the effects of jet Reynolds number, the distance between the nozzle exit and cooling surface apex, and the distance from the stagnation point in the circumferential direction. The resulting characteristics of heat transfer at the stagnation point and the variation of heat transfer along the circumferential direction including the existence of secondary peak have been explained in conjunction with measured impinge jet flow.

• 대한기계학회논문집B
• /
• 제25권6호
• /
• pp.751-757
• /
• 2001

An experimental study of impinging jet-flow structure has been carried out for a fully developed single circular jet impingement cooling on a flat plate, and the effect of the wall thickness at nozzle exit edge is investigated. Impinging jet flow structures have been measured by Laser-Doppler Velocimeter to interpret the heat transfer results presented previously by Yoon et al.(sup)(10) The peaks of heat transfer rate are observed near the nozzle edge owing to the radial acceleration of jet flow when the nozzle locates close to the impingement plate. The growth of the velocity fluctuations in the wall jet flow is induced by the vortices which originate in the jet shear layer, and consequently the radial distribution of local Nusselt numbers has a secondary peak at the certain radial position. As a wall of circular pipe nozzle becomes thicker for small nozzle-to-target distance, the entrainment can be inhibited, consequently, the acceleration of wall jet flow is reduced and the heat transfer rate decreases.

• 해양환경안전학회지
• /
• 제18권5호
• /
• pp.455-460
• /
• 2012

이 연구에서는 정사각 단면을 갖는 덕트 내부에 원심력의 영향을 받는 유동의 천이특성을 실험 및 수치적으로 규명하였다. 실험적 연구로서 레이저도플러 속도계를 이용하여 축방향속도를 측정하였고, 상용소프트웨어인 플루언트를 이용한 전산유체 시뮬레이션으로 천이특성을 고찰하였다. 유동의 발달은 딘수와 굽힘각에 의존한다는 사실을 알 수 있었으며 덕트의 중앙에서의 속도분포는 원심력 때문에 내외벽보다 낮은 값을 나타내었다.

• 대한기계학회논문집B
• /
• 제25권11호
• /
• pp.1561-1568
• /
• 2001

In the present study, flow characteristics of turbulent pulsating flow in a square-sectional 180$^{\circ}$curved duct were experimentally investigated. The experimental study for air flows in a curved duct are carried out to measure axial velocity profiles, wall shear stress distributions and entrance length in a square-sectional 180$^{\circ}$curved duct by using the Laser Doppler Velocimeter(LDV) system and the data acquisition. Velocity profiles are obtained using the Rotating Machinery Resolver(RMR)and PHASE software in case of turbulent pulsating flow. Finally, it was plotted by the ORIGIN software. The experiment was conducted in seven sections from the inlet (ø = 0$^{\circ}$) to the outlet (ø=l80$^{\circ}$) at 3 0$^{\circ}$intervals of the duct.

• 설비공학논문집
• /
• 제27권7호
• /
• pp.344-353
• /
• 2015

In the present study the characteristics of turbulent oscillatory flows in a square-sectional $180^{\circ}$curved duct were investigated experimentally. A series of experiments for air flow were conducted to measure axial velocity profiles, secondary flow velocity profiles and pressure distributions. The measurements were made by a Laser Doppler Velocimeter (LDV) system with a data acquisition and processing system which includes Rotating Machinery Resolve (RMR) and PHASE software. The results from the experiment are summarized as follows. (1) The maximum velocity moved toward the outer wall from the region of a bend angle of $30^{\circ}$. The velocity distribution had a positive value extended over the total phase in the region of a bend angle of $150^{\circ}$. (2) Secondary flows were generally proportional to the velocity of the main flow. The intensity of the secondary flow was about 25% as much as that in the axial direction. (3) Pressure distributions were effects of the oscillatory Dean number and respective region.

• 설비공학논문집
• /
• 제15권3호
• /
• pp.177-186
• /
• 2003

In the present study, the flow characteristics of developing turbulent flows are investigated at the exit region of a square cross-sectional 180" curved duct with dimensions of 40mm$\times$40mm$\times$4000mm (height $\times$ width $\times$length). Smoke particles produced from mosquito coils were used as seed particles for the LDV measurement. Experiments were carried out to measure axial velocity profiles, shear stress distributions and entrance lengths by using an LDV system and Rotating Machinery Resolver RMR with PHASE software. Experimental results clearly show that the time-averaged Reynolds number does not affect oscillatory flow characteristics because the turbulent components tend to balance the oscillatory components in the fully developed flow region. Also, the velocity profiles are in good agreement with 1/7power law such as the results of steady turbulent flows. The turbulent intensity linearly increases along the walls and is slightly higher, especially in the period of deceleration. On the other hand, the LDV measurements show that shear stress values in slightly higher in the period of deceleration due to the flow characteristics in the exit region. The entrance length where flows become stable appears at the point that is 40 times the length of hydraulic diameter.eter.

• 대한기계학회논문집
• /
• 제17권5호
• /
• pp.1253-1261
• /
• 1993

본 연구에서는 수직 평판에 위치한 후향계단면 위를 흐르는 유체유동의 특성, 즉 재부착점, 박리 및 재순환 영역에 미치는 부력의 영향을 수치해석 및 실험으로 조사한다. 유동의 가시화를 통해 재부착점의 위치를 측정하며 레이저도플러 유속계 (5W,Ar-Ion,DANTEC)에 의한 속도분포 및 CTA(constant temperature anemoneter,55M01 과 55M20, DANTEC)를 사용한 온도분포를 동시에 측정 함으로써 유동 특성 및 열전달에 미치는 부력의 영향을 검토한다.

• 대한기계학회논문집
• /
• 제12권4호
• /
• pp.847-864
• /
• 1988

본 연구에서는 연료분출에 박리가 있는 경우와 없는 경우 각각에 대하여 화염 대 근처의 국부가속 현상이 박리에 의하여 어떻게 영향을 받는가를 실험적으로 규명하 고, 나아가서 종래에 행해져 왔던 관련 연구 결과를 재검토할려고 한다.

• Nuclear Engineering and Technology
• /
• 제24권3호
• /
• pp.263-273
• /
• 1992

핵연료 집합체의 속도분포, 압력강하는 열수력 설계와 안전해석에 중요하다. 본 실험적 연구의 목적은 봉다발 지지 격자 하류에서의 수력학적 혼합을 고찰하는데 있다. 이 연구에서 가압경수로형 5X5 봉다발 부수로의 상세한 수력학적 특성들을 1차익 He-Ne LDV를 이용하여 측정하였다. 축방향 유속, 난류강도와 압력강하를 주로 측정하였고 LDV의 정렬을 조정하여 측방향의 유속, 난류강도, Reynolds 전단응력 등도 역시 측정하였다. 봉다발의 마찰계수와 지지 격자의 손실계수는 측정된 압력 강하로부터 평가하였다. 서로 다른 종류의 지지 격자의 수력학적 혼합성능을 이웃하는 부수로 간에서의 난류 횡류 혼합률을 예측함으로써 고찰할 수 있었다.

• 대한조선학회논문집
• /
• 제56권5호
• /
• pp.410-417
• /
• 2019

An axisymmetric submerged body(L=5.6m, Diam=0.53m) is installed in Large Cavitation Tunnel (LCT) of KRISO and the nominal and total velocities without and with the propeller in operation, respectively, are measured using Laser Doppler Velocimeter (LDV). The flow field is nearly axisymmetric except the wake of the supporting strut, and is considered ideal to study the hydrodynamic interaction between the propeller and the oncoming axisymmetric sheared flow. The measured velocity data are then provided to compute the propeller-induced velocity to get the effective velocity, which is defined by subtracting the propeller-induced velocity from the total velocity. We adopted, in computing the induced velocity, two different methods including the vortex lattice method and the vortex tube actuator model to evaluate the resultant effective velocity distribution. To secure a fundamental base of experimental data necessary for the research on the effective wake, we measured the drag of the submerged body, the nominal and total velocity distributions at various axial locations for three different tunnel water speeds.