• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 C
• /
• pp.851-853
• /
• 1999

DLC thin films have been fabricated by pulsed laser deposition with various deposition parameters. The characterization of fabricated thin films was performed depending on the deposition parameters. As the kinetic energies provided by deposition temperature and the laser energy density were increased, the film showed graphite properties. Structural properties of the films were investigated by Raman spectroscopy. The growth energy should be optimized to fabricate high quality DLC thin films. DLC films showed high hardness and their friction coefficient was measured to be about 0.2 regardless of the load of the ball pin.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.54-57
• /
• 2004

ZnO thin films on (001) sapphire substrates have been deposited by pulsed laser deposition(PLD) technique using an Nd:YAG laser with a wavelength of 266 m. During deposition, the experiment of the deposition of ZnO thin films has been performed for substrate temperatures in the range of $400^{\circ}C$ and flow rate of 350 sccm, films have been annealed at various substrate temperatures after deposition. After post-annealing treatment in the oxygen ambient, the structural properties of ZnO thin films were characterized by diffraction (XRD), SEM and the optical of the ZnO were characterized by photoluminescence (PL).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.224-227
• /
• 1999

Ferroelectric Pb(Zr$\sub$0.52/Ti$\sub$0.48/)O$_3$ thin films were fabricated by pulsed laser deposition, mainly varying process conditions such as substrate temperature, oxygen pressure, and laser energy, PZT films annealed at more than 600$^{\circ}C$ were crystallized into pure perovskite phases regardless of deposition temperatures. Lower deposition temperature of 400$^{\circ}C$ accompanied with post-annealing at 650$^{\circ}C$ resulted in denser microstructures with extremely small grains compated to those of thin films annealed at higher deposition temperatures. Hysteresis curves of thin film with small grains exhibitied good squareness and low leakage characteristics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.162-164
• /
• 2004

Nanocrystalline silicon(nc-Si) thin films on the silicon substrates have been prepared by pulsed laser deposition(PLD). The optical and structural properties of films have been investigated depending on deposition temperature, annealing, and oxidation process. When the deposition temperature increased, photoluminescence(PL) intensity abruptly decreased and peaks showed red shift. Annealing process could reduce the number of defect centers. Oxidation had a considerable effect upon the formation and isolation of the nanocrystals. These results indicate that the formation mechanism of Si nanocrystals grown by PLD can be explained by three steps of growth, passivating defect centers, and isolation, sequentially.

• 한국CDE학회논문집
• /
• 제8권3호
• /
• pp.150-156
• /
• 2003

Direct Metal Deposition (DMD) is a new additive process producing three-dimensional metal components or tools directly from CAD data, which aims to take mold making and metalworking in an entirely new direction. It is the blending of five common technologies: lasers, CAD, CAM, sensors and materials. In the resulting process, alternatively called laser cladding, an industrial laser is used to locally heat a spot on a tool-steel work piece or platform, forming a molten pool of metal. A small stream of powdered tool-steel metal is then injected into the metal pool to increase the size of the molten pool. By moving the laser beam back and forth, under CNC control, and tracing out a pattern determined by a computerized CAD design, the solid metal part is eventually built line-by-line, one layer at a time. DMD produces improved material properties in less time and at a lower cost than is possible with traditional fabrication technologies.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.539-542
• /
• 2000

ZnO thin films for light emission device have been deposited on sapphire and silicon substrates by pulsed laser deposition technique(PLD). A Nd:YAG laser was used with the wavelength of 355 nm. In order to investigate the emission properties of ZnO thin films, PL measurements with an Ar ion laser as a light source using an excitation wavelength of 351 nm and a power of 100 mW are used. All spectra were taken at room temperature by using a grating spectrometer and a photomultiplier detector. ZnO exhibited PL bands centered around 390, 510 and 640 nm, labeled near ultra-violet (UV), green and orange bands. Structural properties of ZnO thin films are analized with X-ray diffraction (XRD).

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권5호
• /
• pp.344-348
• /
• 1999

Diamond like carbon(DLC) thin films possesed not only marvelous material characteristics such as large thermal conductivity, high hardness and being chemically inert, but also possesed negative electron affinity (NEA) properties. The NEA is an extremely desirable property of the material used in microelestronics and vacuum microelestronics device. DLC films were fabricated by pulsed laser deposition(PLD). Theeffect of the laser energy density and the substrate temperature on the properies of DLC films was investigated. The experiment was accomplished at temperatures in the range of room temperature to $600^{\circ}C$. The laser energy density was in the range of 6 $J/cm^2$ to 16 $J/cm^2$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1149-1151
• /
• 1995

In order to examine the deposition mechanism for $SiO_2$ by ArF(193nm) excimer Laser using $Si_2H_6$ and $N_2O$ gas mixture, deposition rate and refractive index were measured and creative modeling on film deposition was established by suggesting now precursor and film growing mechanism.

• 전기학회논문지
• /
• 제59권1호
• /
• pp.113-115
• /
• 2010

In this study, ZnO films have been grown on PES(polyethersu]fone) substrate by PLD(pulsed laser deposition) and characterized as a change of laser density and substrate temperature. Growing conditions were changed with substrate temperatures ranging from 50 to $200^{\circ}C$ and laser densities ranging from $0.2\sim0.4 J/cm^2$. Optical and structural properties were measured by XRD, SEM, AFM, PL measurement.

• 한국전기전자재료학회논문지
• /
• 제24권2호
• /
• pp.108-111
• /
• 2011

The semiconducting material of ZnO in II-VI group was well known as its good application for photo electronics, chemical sensors and field effect transistors due to the remarkable optical properties with wide energy band gap and great ionic reactivities. Up to now the growth of a good quality of ZnO film has been issued for better performances. Even though there were many deposition methods for making ZnO films, pulse laser deposition methods have been preferred for high crystalline films. In this report, the ZnO film was also created by pulsed laser deposition technique which also showed high crystalinity. By controlling several factors when deposited, it was investigated that the optimal condition for ZnO film formation. Mainly, oxygen partial pressures and growth temperatures were changed when ZnO films were synthesized and followed the characterization by HRXRD and AFM.