• 대한치과보철학회지
• /
• 제38권4호
• /
• pp.510-525
• /
• 2000

The effects of pretreatment of Co-Cr alloy, including two adhesive primers that contain either MDP or MAC-10, and silicoating on the bond The result sobtained as follows; o Strength of 4-META/MMA-TBB resin were investigated using FT-IR, SEM, and EDAX. o In the SEM observation of surface morphologies, the sandblasted specimen exibited a very rough surface, whereas the surfaces of the two groups primed with either MDP or MAC-10 were covered with a layer of primer, and the surface morphology of the silicoated specimen remained almost the same after sandblasting. o Before the thermocycling tests, the group treated with MDP demonstrated the highest mean tensile bond strength and the sandblasted group showed the lowest bond strength. o After 20,000 thermocyling, the mean tensile bond strength of the sandblasted group exhibited a 50% reduction in bond strength, while the others showed a $20\sim30%$ reduction. o Observation of the metal-resin interface revealed that in all groups the resin permeated the rough surface formed by sandblasting thereby producing a mechanical bond between the metal and the resin. It was also found that thermocycling resulted in a gap formation at the metal-resin interface of the specimens, and the sandblasted group exhibited a larger gap width than the other groups. o In fracture mode, all specimens indicated a cohesive fracture within the resin before thermocycling. However, thermocyling produced adhesive failure at the edge of the resin-metal interface in most specimens. The sandblasted group, which exhibited the lowest bond strength after thormocycling, also demonstrated the largest area of adhesive failure.

• 한국전기전자재료학회논문지
• /
• 제15권5호
• /
• pp.435-440
• /
• 2002

In this study, we have investigated photo-induced changes of optical energy gap( $E_{OP)}$ and photoluminescence (PL) in amorphous ($\alpha$-) S $e_{100-x}$G $e_{x}$ (x=5, 25 and 33) thin films prepared by conventional thermal evaporation method. In the $\alpha$-S $e_{100-x}$G $e_{x}$ thin film, the $E_{OP}$ is obtained by a linear extrapolation of the ($\alpha$hν)$^{\frac{1}{2}}$ versus hν plot to the energy axis using the optical absorption coefficient ($\alpha$) calculated from the extinction coefficient k measured in the wavelength range of 290~900nm. Although the values of $\Delta$ $E_{OP}$ are very different, all films exhibit photo-induced photo-darkening (PD) effect that is a red shift of $E_{OP}$ . In particular, $\Delta$ $E_{OP}$ in $\alpha$-S $e_{75}$ G $e_{25}$ thin film exhibits the largest value (i, e., $\Delta$ $E^{OP}$ ~40meV for $\alpha$-S $e_{95}$ G $e_{5}$ , $\Delta$ $E_{OP}$ ~200meV for $\alpha$-S $e_{75}$ G $e_{25}$ , $\Delta$ $E_{OP}$ ~130meV for $\alpha$-S $e_{67}$ G $e_{33}$ ). PL spectra in $\alpha$-SeGe by hν$_{HeCd}$ have no-Stokes shift (SS) and show a tendency dependent on both composition and illumination time. We explain the energy-induced phenomena such as the PD and thermal bleaching, the native charged-defect generation and the no-SS PL, etc..the PD and thermal bleaching, the native charged-defect generation and the no-SS PL, etc..tc..

• 대한치과기공학회지
• /
• 제40권4호
• /
• pp.209-215
• /
• 2018

Purpose: The purpose of this study was to evaluate the clinical acceptability of the marginal and internal gap of Co-Cr metal copings fabricated with stereolithography (SLA). Methods: Titanium master dies were milled after scanning of the prepared tooth (n=30). For group I, Co-Cr metal copings were made from conventional lost-wax technique(LWT, n=10). For group II, the master dies were scanned and designed with CAD system. Then, metal copings were milled with Co-Cr(SUB, n=10). For group III(ADD, n=10), the scanning and design procedures were same as group II and burn-out resins were fabricated with SLA device. The marginal and internal discrepancies were measured under an optical microscope(100x) on ten reference points and were statistically analyzed with one-way ANOVA(${\alpha}=.05$). Results: The mean total discrepancies were $53.76{\pm}12.42{\mu}m$ in the LWT group and $69.82{\pm}15.48{\mu}m$ in the ADD group. The SUB group showed the largest total mean value $110.33{\pm}13.77{\mu}m$. There was statistically significant difference between the SUB and the other groups(P<0.05). Conclusion : Co-Cr metal copings fabricated with SLA technology showed clinically acceptable value on marginal and internal gap and there was no statistically significant difference between conventional lost-wax technique and SLA.

• 한국전기전자재료학회논문지
• /
• 제37권3호
• /
• pp.292-296
• /
• 2024

In this study, Iron (III) oxide-hydroxide (δ-FeOOH) was successfully synthesized using hydrogen peroxide (H₂O₂) as an oxidizing agent. The synthesis of δ-FeOOH was carried out by controlling the amount of H₂O₂, and pure δ-FeOOH was successfully synthesized in ranges from 0.2 mL to 0.6 mL of H₂O₂. The size of the synthesized δ-FeOOH particles was compared by controlling the amount of oxidant H₂O₂. The average particle size of the synthesized pure δ-FeOOH particles increased from 875.1 nm to 897.2 nm as the amount of H₂O₂ was increased. The optical properties of δ-FeOOH synthesized under these specific conditions were investigated. All δ-FeOOH showed a similar trend of increasing and decreasing light absorption from 800 nm to 400 nm, although there was a slight difference in the amount of light absorption, with the largest amount of light absorption at 410 nm. The band gap energy of δ-FeOOH through the Tauc plot method was about 2.1~2.2 eV when H₂O₂ was 0.2~1.4mL. With a sufficient small particle size, simple control of that particle size, and a small band gap energy enough to absorb light in the visible spectrum, δ-FeOOH could be useful in a variety of applications, including photoelectrochemistry and battery electrodes.

• 한국가정과교육학회지
• /
• 제16권1호
• /
• pp.79-91
• /
• 2004

이 연구의 목적은 중$.$고등학교 기술$.$가정과 교사의 수행평가에 대한 관심도 및 실행수준, 실행실태, 지원정도를 분석하여 수행평가의 보다 효과적인 실행을 위한 지원 체제를 수립하기 위한 기초자료를 제공하는 데 있다. 연구 자료는 텍사스대학의 교사 교육을 위한 연구 개발 센터에서 Hall. Hord등이 개발한 관심에 기초한 혁신채택 모형을 연구 도구로 하여 경기도에 소재한 95개 중$.$고등학교 기술$.$가정과 교사를 대상으로 우편을 통한 설문지로 수집하였으며, 157부를 최종 분석에 사용하였다. 자료는 SPSS/WIN 프로그램을 이용하여 평균, 표준편차, 백분율, t-test, ANOVA, 카이검증 분석을 실시하였다. 이 연구를 통해 밝혀진 결과를 요약하면 다음과 같다. 첫째, 기술$.$가정과 교사들의 수행평가에 대한 관심도는 대부분이 실행 초기 상태를 나타내고 있었던 반면에, 실행수준은 4. 5단계에 많은 빈도를 보여 교사들은 자신의 수행평가 실행수준을 관심도가 시사하는 것보다 더 높게 평가하는 것으로서 이는 학교에서 본인의 관심도와는 관계없이 업무상 평가와 관련된 지침을 만들고 평가에 대한 근거 자료를 남겨야 하는 교육 현장의 현실과도 관련이 있는 것으로 보인다. 둘째. 수행평가 실행실태는, 실행수준이 높은 교사일수록 수행평가 본래의 취지에 부합된 실행실태를 보여주었으며, 수행평가 시행을 위한 지원에 대한 기술$.$가정과 교사들의 인식 정도를 조사 분석한 결과는 전반적인 평균점수가 7점 만점에 3점 이하로 나타나 지원의 정도가 미비한 것으로 나타났으며, 관심유형 및 실행 수준별 분석에서도 단계별 지원이 전반적으로 이루어지지 못하고 있음을 알 수 있다. 이상과 같이 중$.$고등학교 기술$.$가정과 교사들의 수행평가에 대한 관심도와 실행수준. 실행형태를 알아본 결과 교사들의 개인적 특성에 따라 관심유형과 실행수준에서 많은 차이점이 있음을 알 수 있었으며, 그 실행형태 또한 다양하게 나타나고 있으나 수행평가에 대한 지원 정도를 분석한 결과는 관심유형별로 차별화 된 지원이 전혀 이루어지지 못하고 있는 실정이므로 수행평가의 효과를 극대화하기 위해서는 교사 자신이 수행평가에 대해 지속적인 관심을 가져야 하고, 학교당국. 교육행정가. 교육전문가 등의 변화 지원자는 수행평가 실행과정 동안 발생하는 문제들을 해결할 수 있도록 개별화된 지원을 아끼지 않아야 한다. 따라서 교사들의 관심유형과 실행수준에 따라 수행평가에 대한 지원을 달리함으로써 교사들의 관심도와 실행수준을 향상시켜야 할 것이며 보다 효과적인 수행평가가 실시되도록 해야 할 것이다.

• 한국치위생학회지
• /
• 제11권2호
• /
• pp.243-250
• /
• 2011

Objectives : The purpose of this study was to examine the oral health behavior and knowledge of middle schoolers in an attempt to facilitate the selection of what to teach about oral health. Methods : The subjects in this study were 315 students at three different middle schools located in the city of Gunsan. After a self-administered survey was conducted by using structured questionnaires in collaboration with their homeroom teachers, the answer sheets from 315 students were gathered. And the answer sheets from 302 students were analyzed with SPSS 12.0 program except 13 incomplete ones. The findings of the study were as follows: Results : 1. By gender and grade, the middle school boys(51.3%) outnumbered the middle school girls(48.7%), and the seventh, eighty and ninth graders respectively accounted for 31.5, 32.8 and 35.8 percent. 2. As to the parts of the mouth they brushed, the largest number of the seventh graders(31.6%) and ninth graders(56.5%) brushed their teeth and tongue. The largest group of the eighth graders(39.4%) brushed their teeth, tongue and gums, and the gaps between them and the others were statistically significant. 3. In regard to toothbrushing frequency, the ninth graders did that 2.62 times, which was the largest frequency, but the gap between them and the others was not statistically significant. 4. Concerning school oral health education experiences, the rates of the seventh, eighth and ninth graders who had ever received that education stood at 69.5, 50.6 and 50.5 percent respectively, and those students significantly outnumbered the others who hadn't(p<0.01). 5. As for the relationship of their oral health behavior scores to toothbrushing frequency, there was a statistically significant correlation between the two(r=0.227, p<0.001). And the oral health knowledge scores had a statistically significant correlation to toothbrushing frequency (r=0.116, p<0.05) and oral health behavior scores(r=0.358, p<0.001). Conclusions : It is concluded that proactive oral health education must be made through diverse programs and systems. Also, regular oral examination and active oral health program for preventing dental caries and periodontal disease should be proliferated in order to evaluate achievement and effectiveness and maintain oral health care.

• 한국치위생학회지
• /
• 제6권4호
• /
• pp.349-359
• /
• 2006

The purpose of this study was to help improve the quality of education to keep up with fast-changing environments in educating sector. Relevant literature and data were reviewed, and the subjects in this study were dental hygiene juniors at seven two-year colleges in the Seoul metropolitan area and other regions, on whom a survey was conducted for about three months from August through October, 2004, to assess their satisfaction level with their major and educational environments. And it's concluded that in order to attract more new students and foster qualified students, dental hygiene practice labs should be improved on a large scale, and that there should be a great deal of investment in teaching facilities. The major findings of the study were as follows: 1. As for satisfaction with major choice, 57.5% of the students investigated, the largest percentage, expressed satisfaction with their major. 27.8%, the second largest group, found their choice not to be bad. 2. Regarding satisfaction with the state of practice labs, 41.9% were pleased with practice labs. This rate was quite lower than that of nursing students, as 64.2% of nursing students were pleased with their practice labs.7) 3. As to satisfaction with individual practice labs, oral prophylaxis labs were considered most satisfactory, as 53.9% were satisfied with them. Digital radiation labs appeared to be satisfactory the least, which made 77.0% dissatisfied. 4. Whether there were any connections between their working experience as a clinical worker and satisfaction level was investigated. In terms of their satisfaction with major choice and the state of practice labs, the students who had ever worked as a clinical worker were relatively pleased with the state of practice labs. As for satisfaction with each practice lab, those who had ever served as a clinical worker before being admitted into college expressed more satisfaction with radiation practice labs(p<0.05) and digital radiation labs(p<.05) than the others who hadn't. The gap between the two was statistically significant. 5. In regard to the causes of dissatisfaction with practice labs, 93.7 and 80.0% were respectively dissatisfied with digital radiation labs and basic dental hygiene labs because their colleges were devoid of those labs. 51.6%, the largest group, found oral prophylaxis labs unsatisfactory because of their frequent breakdown. In the event of most of the other practice labs, the greatest percentage were discontented due to a shortage of equipment.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.267.2-267.2
• /
• 2016

Semiconductor photo-catalysis offers the potential for complete removal of toxic chemicals through its effective and broad potential applications. Various new compounds and materials for chemical catalysts were synthesized in the past few decades. As one of the most important II-VI group semiconductors, zinc sulfide (ZnS) with a wide direct band gap of 3.8 eV has been extensively investigated and used as a catalyst in photochemistry, environmental protection and in optoelectronic devices. In this work, the ZnS films and nanostructures have been successfully prepared by wet chemical method. We show that the agglomerates with four successive scales are always observed in the case of the homogeneous precipitation of zinc sulfide. Hydrodynamics plays a crucial role to determine the size of the largest agglomerates; however, other factors should be invoked to interpret the complete structure. In addition, studies of the photocatalytic properties by exposure to UV light irradiation demonstrated that ZnS nanocrystals (NCs) are good photo-catalysts as a result of the rapid generation of electron-hole pairs by photo-excitation and the highly negative reduction potentials of excited electrons. A combination of their unique features of high surface-to volume ratios, carrier dynamics and rich photo-catalytic suggests that these ZnS NCs will find many interesting applications in semiconductor photo-catalysis, solar cells, environmental remediation, and nano-devices.

• 대한소아치과학회지
• /
• 제10권1호
• /
• pp.67-76
• /
• 1983

The state of pulp and dental hard tissue during the process of resorption and shedding of 104 non-carious primary teeth was assessed by histomorphologic study. The teeth were extracted from the Korean school children aged 5 to 15 and classified into preshedding, shedding, delayed shedding groups according to the age of the child at the time of extraction, The results were as follows: 1. The inflammatory cell infiltration in primary pulp tissues occurred in 61.5% of observed teeth and were increased in the order of preshedding, shedding and delayed shedding stages. 2. The odontoclasts were appeared in 43.3% of observed teeth and were increased in the order of preshedding, shedding and delayed shedding stages. 3. The polymorphonuclear leukocytes and odontoclasts couldn't be observed in the exfoliated primary pulp tissues before the process of resorption has involved the root surface about 1.8mm subjacent to the cemento-enamel junction. 4. The intact root surface was the longest and largest in the preshedding stage. 5. The resorption process of primary teeth roots occurred mainly in the stage of preshedding and shedding stages. 6. There was a tendency of repair of resorbing root surfaces in the delayed shedding stage.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.65-68
• /
• 2005

This paper investigated the engineering properties of cement mortar mixed with more than 2 kinds of sand. For fresh mortar properties, unit volume weight is constant regardless of mixing content and type of sand. An increase in contents of river and crushed sand resulted in an increase in flow, whereas an increase in recycled sand contents reduced flow. Gap between maximum flow in N3C0R0 and minimum flow in N0C0R3 exhibited about $12\%$. Compressive strength at 28 days ranged from 32 to 36 MPa in order for crushed sand, river sand and recycled sand. Mortar with mixed sand along with river sand and crushed sand showed compressive strength comparable to crushed sand. An increase of fraction of recycled sand in mixed sand resulted in a decrease in compressive strength. For drying shrinkage, N0C0R3 had the largest drying shrinkage among various mixture type. The combination of large contents of recycled sand and small contents of river and crushed sand had a large amount of drying shrinkage.