• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.3
• /
• pp.263-268
• /
• 2015

This paper describes lost motion analysis for a novel 6-DOF ultra-precision positioning stage. In the case of flexure hinge based precision positioning stage, lost motion is generated when the displacement of actuator is not delivered completely to the end-effector because of the elasticity of flexure hinge. Consequently, it is need to compute amount of lost motion to compensate the motion or to decide appropriate control method for precision positioning. Lost motion analysis for the vertical actuation unit is presented. The analysis results are presented in two ways: analytic and numerical analyses. It is found that they closely coincide with each other by 1% error. In finite element analysis result, the amount of lost motion is turned out to be about 3%. Although, the amount is not so large, it is necessary procedure to check the lost motion to establish the control method.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.6
• /
• pp.56-64
• /
• 2013

Crabbing motion is the pure sway motion of a ship without surge velocity. Thus, it can be applied to a berthing operation. Crabbing motion is induced by a peculiar operation method called the push-pull mode. The push-pull mode is induced by using a combination of the main propeller and side thruster. Two propellers generating the same amounts of thrust and rotating in opposite directions produce some yawing moment on a vessel but do not induce longitudinal motion. With the additional operation of side thrusters, the push-pull mode is used to induce a large amount of lateral force. In this paper, three-degree-of-freedom equations of motion such as for the surge, sway, and yaw are constructed for the crabbing motion. Based on these equations of motion, a feedback linearization control method is applied to auto-berthing control for a twin-screw ship with side thrusters. The controller can deal with the nonlinearity of a system, which is present in the berthing maneuver of a twin screw ship. A simulation of the auto-berthing of a ship is performed to validate the performance of the designed controller.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.3
• /
• pp.69-80
• /
• 2007

The purpose of this study was to investigate the difference of ground reaction forces of swimming athletes during their starting motion and to find out the most effective starting motions which were used in swimming athletes. The subjects were 9 male and 8 female high school swimming athletes who were athletic career over 7 years and used three starting motions in competition. The ground reaction forces were measured from each athletes performing three starting motion each of the open grap starting motion, closed grap starting motion and track starting motion. For the measurement, the force platform of AMTI company was utilized, and the analysis on measured ground reaction forces were used of Biosoft(Ver. 1.0). The items measured were stance time, Fz max deceleration force and Fz max deceleration force time, Fz mid stance force and Fz mid stance force time, Fz max acceleration force and Fz max acceleration force time, Torque maximum and Torque maximum time, Torque average, Excursion along Y axis of center of pressure of foot, Excursion along X axis of center of pressure of foot, Length of center of pressure of foot, Average velocity of center of pressure of foot. The data measured by the closed grap starting motion, open grap starting motion and track starting motion were analyzed by one-way repeated ANOVA. The results were as follows ; 1. The Fz max deceleration force time, Fz mid stance force, Fz max acceleration force, Torque maximum and Torque maximum time, Excursion along Y axis of center of pressure of foot, Average velocity of center of pressure of foot were significantly fast and large in the closed grap starting motion then open grap starting motion and track starting motion. 2. The Excursion along Y axis of center of pressure of foot was significantly long in the closed grap starting motion then open grap starting motion and track starting motion.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.49 no.4
• /
• pp.23-31
• /
• 2012

This paper proposes a motion estimation-based super resolution algorithm to restore input low-resolution images of large movement into a super-resolution image. It is difficult to find the sub-pixel motion estimation in images of large movement compared to typical experimental images. Also, it has disadvantage which have high computational complexity to find reference images and candidate images using general motion estimation method. In order to solve these problems for the traditional two-dimensional motion estimation using the proposed registration threshold that satisfy the conditions based on the reference image is determined. Candidate image with minimum weight among the best candidates for super resolution images, the restoration process to proceed with to find a new image registration algorithm is proposed. According to experimental results, the average PSNR of the proposed algorithm is 31.89dB and this is better than PSNR of traditional super-resolution algorithm and it also shows improvement of computational complexity.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.6
• /
• pp.452-459
• /
• 2015

It is important to use bench test results in the design process of anti-rolling tanks. Traditional bench tester is usually designed to perform only roll motions about a fixed axis and relatively small so that the viscous effects may not be neglected. Novel bench tester which could adjust the motion center to realize the coupled motion of sway and roll has been devised and manufactured therefore, large scaled bench tester could be utilized for designing the passive anti-rolling tanks. The time history of the reference signal from the rotation sensor of the bench tester have been recorded and processed to determine the phase angle to derive the Response Amplitude Operator(RAO) of the stabilized ship. The breadth of ART tank model should be large up to 2 m to diminish viscous scale effect and the vertical position of the tank can be varied with the ship's center of motion. The periods and the amplitude of roll motion can be varied from 1.5 sec to 5 sec and up to ±20°, respectively. The components of the tester was expressed in three dimensional digital mockup (DMU) and assembled together in the CAD space. The final configuration of the bench tester has been determined by confirming the smooth operation of the moving parts without interference through the animation in CAD space. New analytic logic are introduced for the determination of hydrodynamic moment and phase difference due to fluid motion in ART and verified through the test. The developed bench tester is believed to be effective and accurate for the verification of stabilization effect of ART taking into the consideration of the sway effect in the design stage.

• Ocean Systems Engineering
• /
• v.8 no.4
• /
• pp.427-439
• /
• 2018

Floating Production Storage and Offloading (FPSO) units have the advantages of their ability to provide storage and offloading capabilities which are not available in other types of floating production systems. In addition, FPSOs also provide a large deck area and substantial topsides payload capacity. They are in use in a variety of water depths and environments around the world. It is a good solution for offshore oil and gas development in fields where there is lack of an export pipeline system to shore. However due to their inherently high motions in waves, they are limited in the types of risers they can host. The Low Motion FPSO (LM-FPSO) is a novel design that is developed to maintain the advantages of the conventional FPSOs while offering significantly lower motion responses. The LM-FPSO design generally consists of a box-shape hull with large storage capacity, a free-hanging solid ballast tank (SBT) located certain distance below the hull keel, a few groups of tendons arranged to connect the SBT to the hull, a mooring system for station keeping, and a riser system. The addition of SBT to the floater results in a significant increase in heave, roll and pitch natural periods, mainly through the mass and added mass of the SBT, which significantly reduces motions in the wave frequency range. Model tests were performed at the Korea Research Institute of Ships & Ocean Engineering (KRISO) in the fall of 2016. An analytical model of the basin model (MOM) was created in Orcaflex and calibrated against the basin-model. Good agreement is achieved between global performance results from MOM's predictions and basin model measurements. The model test measurements have further verified the superior motion response of LM-FPSO. In this paper, numerical results are presented to demonstrate the comparison and correlation of the MOM results with model test measurements. The verification of the superior motion response through model test measurements is also presented in this paper.

• Journal of the Korea Computer Graphics Society
• /
• v.28 no.4
• /
• pp.13-22
• /
• 2022

In this paper, we propose a single framework based on the MPM(Material Point Method) that can represent the dynamic angular motion of the elementary particle unit. In this study, the particles can have various shapes while also describing linear and angular motion. As a result, unlike other particle-based simulations, which only represent linear movements of spherical (e.g. Circle, Sphere) particles, it is possible to express the visually dynamic motion of them. The proposed framework utilizes MPM, due to the fact that rotational motion can be decomposed and derived from large deformation. During the integration process of the presented technique, a deformation gradient tensor is decomposed by polar decomposition theory for extracting rotation tensor. By applying this together with the linear motion of each particle, as a result, it is possible to simultaneously express the angluar and linear motion of the particle itself. To verify the proposed method, we show the simulation of rotating particles scattering in the wind field, and the interaction(e.g. Collision) between a moving object and them by comparing the traditional MPM

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.1-11
• /
• 1997

When a barge is towed by a tug boat using a tow line, the barge is frequently subject to a large sway motion induced from its inherent yaw motions. This large sway motion combined with external forces due to winds and waves may makes the towing to be difficult or even dangerous. It has been reported that in worse situations, barges or tugs are capsized. In addition, the large sway motion of the towed barge gives a menace to the safety of ships navigating nearby. This paper is the results of the experimental investigation into the course stability of an 8,000 DWT barge using a Towing Tank and a Circulating Water Channel. Various skegs are designed and course stability tests for the barge with skegs are conducted in calm water and in irregular waves. It is observed that an effective skeg attached to the barge enables the sway motion to be zero while the sway amplitude of the bare hull is around 10 times its breadth.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.4
• /
• pp.3-14
• /
• 1990

For a moored body on the sea surface, incident waves with narrow-banded spectra excite the body oscillations of short and long periods. Since the period of slow oscillations can be as long as the natural period of the moored body in horizontal modes, resonance can occur and resulting large motions may cause significant strains in mooring cables. By using the perturbation method of multiple scales, the large slow motion can be analyzed without solving any second-order potentials explicitly. To the leading order, the flows associated with the fast and slow motions interact only parametrically and thus they can be studied separately. It is found that the slow motion strongly depends on the mooring stiffness. In particular, if the moring stiffness is considerably weak compared to the body inertia, the slow motion is highly amplified near resonance. It is also shown that the slow motion is associated with the generation of long waves.

• Fashion & Textile Research Journal
• /
• v.21 no.4
• /
• pp.468-479
• /
• 2019

This study used a three-dimensional-analysis method to quantitatively analyze the change of clothing appearance according to a gusset added to bodice and sleeve patterns for men in their twenties. Comparing six different patterns, the study found that patterns P1 and P2 with little gusset did not have a large difference in the strain map, and pattern P6 had no gusset in the motion of raising the arm $28^{\circ}$ to the side (M1). When the arm was raised $45^{\circ}$ to the side (M2), the P1 pattern had the smallest deformation, and only the P5 pattern had a large deformation from the neck to the armhole area. In contrast, except for in the P3 pattern, large wrinkles formed in the front and back when the arm was raised above $158^{\circ}$ (M3) from the side of the waist to the armpit. In addition, P3 had the smallest change in the hem of the bodice and sleeves. However, the appearance of P2, P3, and P5 was excellent when the arm was moved forward (M4), and the P2 and P5 patterns were the smallest at the bodice and sleeve hem. The P6 pattern showed the least fitness in terms of function. In the case of raising the arm, there was a strong correlation between gusset size and motion function, but when the motion of the arm changed, the motion function did not improved just by changing the ease size.