본 연구는 국내의 대표적인 연약지반인 남해안 광양지역과 양산지역의 피스톤 샘플러와 대형블록시료로 수행된 실내시험 시료를 이용하여 교란도 분석을 시행하고 교란에 따른 실내시험 압축지수 특성을 평가하기 위하여 계측침하량 분석에 의한 역해석 압축지수와 비교 분석하였다. 본 연구대상지역의 피스톤 시료에 의한 실내시험 결과로 시료교란도 분석을 수행한 결과 대부분 시료가 품질이 불량한 것으로 평가되어 실내시험결과로 산정된 압축지수를 이용한 설계 예측침하량이 과소평가되었음을 알 수 있었다. 인근지역에서 수행된 시험자료에 대한 교란도 분석결과 대형블록시료가 피스톤 시료보다 교란도가 작은 것으로 분석되었다. 계측침하량을 이용한 장래침하량 예측기법인 쌍곡선법, Hoshino법, Asaoka법, ${\sqrt{S}}$법으로 예측한 결과 일부 측점의 예측자료를 제외하고는 예측기법별 신뢰도는 동일한 것으로 분석되었다. 피스톤 시료의 압축지수에 대한 교란영향을 보정하기 위하여 Schmertmann의 수정 압축지수와 계측침하량 분석에 의한 역해석 압축지수를 이용하여 피스톤 시료의 압축지수를 추정하는 새로운 보정식을 제시하였다.
The aim of this study is to investigate strength and water purification characteristics of effective microorganism-applied volcanic ash block using flexural strength test and water quality analysis. The specimens were prepared with volcanic ash from Mt. Baekdusan and Mt. Hallasan, and cement as the ratios of 3.5:1, 4.0:1, 4.5:1, 5.0:1 with and without metakaolin. Flexural strength degraded with increasing of the amount of volcanic ash, and increased with addition of metakaolin as a binder. Based on these results, the optimal ratio for fabricating volcanic ash-cement mixture block is determined as 3.5:1 with metakaolin. Furthermore, from water quality analysis on contaminated water, removal ability of effective microorganism-applied volcanic ash-cement mixture block and caged volcanic ash block against T-N, T-P and SS was highly evaluated because of adsorption due to the large specific surface area of volcanic ash. Hence, volcanic ash-cement mixture block and caged volcanic ash block possibly contribute to water purification.
후방산란전자(BSE)는 입사전자빔이 시료와 충돌하면서 발생한다. BSE 이미징은 시료의 화학적 특성을 구분할 수 있는 조성대비를 제공한다. 집속이온빔장치(FIB)는 전계방사형 주사전자현미경(FESEM)과 결합할 수 있으므로 이중빔 체계(FIB-FESEM)가 구현된다. 갈륨(Ga) 이온빔으로 10~100 nm 두께로 시료를 절삭할 수 있으므로 FIB-FESEM은 플라스틱으로 포매된 블록의 면을 z축 고해상도를 유지하며 연속적으로 이미징할 수 있다. BSE이미지의 대비를 반전시키면 투과전자현미경의 이미지와 유사하다. 연속블록면 이미징의 또 다른 방안으로써 특수한 초박절편기가 FESEM 내부에 장착된 것이 $3View^{(R)}$로 상용화되어 있다. 이로써 플라스틱으로 포매된 시료의 내부 구조를 넓은 면적을 연속적으로 이미징 할 수 있으므로 3차원 재구성도 용이하게 된다. 이러한 FESEM에 기반한 두 가지 방식은 복잡한 생물계의 총체적인 이해를 위하여 세포 및 세포 수준 이하의 구조물 간의 공간적 연관성을 규명하는 데 활용될 수 있다.
Two kinds of alumina specimens with different grain size (1 and 51 $\mu\textrm{m}$) but same density were prepared by hot-pressing. Fracture strength and fracture toughness of these specimens at low strain rate, sonic velocity, and elastic property were evaluated. Ballistic performance against Cal. 50 AP projectile was characterized by thick-backing method by using A16061-T6 reference block. Mechanical properties measured at low strain rate showed that the specimen with samll grain (SG) were better than specimen with large grain (LG). Fracture strength and fracture toughness of LG specimen were 131 MPa and 3.01 MPa{{{{ SQRT { m} }}, but those of SG specimen were 349 and 4.23, respectively. Sonic velocity and elastic properties of these specimen were similar, but bulk velocity and bulk modulus were different at amount of 4 and 9%. The tendency of ballistic performance was not consistent with the mechnaical properties at low strain rate. The ballistic performance based on quantitative efficiency revealed that the LG specimen (5.13) was ballistically better than the SG specimen (4.00) in spite of their lower mechanical properties.
This study evaluated the multi-bonding performances of timbers as well as those of reinforcement and timber to obtain data for preparing guidelines regarding the use of timbers as large structural members. For the multi-bonding performances of timbers, four types of bonding surfaces were prepared according to the pith position. For the bonding performances of FRP (fiber-reinforced plastic)/steel plate and timber, a total of 11 types of specimens were produced for the selection of the appropriate adhesive. The bonding performances of the produced specimens were evaluated through a water soaking delamination test, a water boiling delamination test, and a block shear strength test. The test results showed that the bonding strength of the bonding surface according to the pith position was highest in the specimen for which the two sections with the pith at the center of the cross-section on timber and between the bonding surfaces (the tangential and radial sections were mixed) were bonded. Furthermore, the specimens for which the section (radial section) with the pith on the bonding surface of the timber was bonded showed a high delamination percentage. The results of the block shear strength test showed that the bonding section did not have a significant effect on the shear strength, and that the measured wood failure percentage was higher than the KS standard value. The PVAc adhesive showed the highest bonding strength between larix timber and GFRP (glass FRP). Furthermore, the epoxy and polyurethane adhesives showed good bonding strength for CFRP (carbon FRP) and structure steel, respectively.
International Journal of Naval Architecture and Ocean Engineering
/
제6권2호
/
pp.459-470
/
2014
During ship design, welding-induced distortions are roughly estimated as a function of the size of the component as well as the welding process and residual stresses are assumed to be locally in the range of the yield stress. Existing welding simulation methods are very complex and time-consuming and therefore not applicable to large structures like ships. Simplified methods for the estimation of welding effects were and still are subject of several research projects, but mostly concerning smaller structures. The main goal of this paper is the application of a multi-layer welding simulation to the block joint of a ship structure. When welding block joints, high constraints occur due to the ship structure which are assumed to result in accordingly high residual stresses. Constraints measured during construction were realized in a test plant for small-scale welding specimens in order to investigate their and other effects on the residual stresses. Associated welding simulations were successfully performed with fine-mesh finite element models. Further analyses showed that a courser mesh was also able to reproduce the welding-induced reaction forces and hence the residual stresses after some calibration. Based on the coarse modeling it was possible to perform the welding simulation at a block joint in order to investigate the influence of the resulting residual stresses on the behavior of the real structure, showing quite interesting stress distributions. Finally it is discussed whether smaller and idealized models of definite areas of the block joint can be used to achieve the same results offering possibilities to consider residual stresses in the design process.
In this study, partially restrained beam-column moment joints in the weak-axis direction were examined using three large-scale specimens subject to cyclic loading in order to assess the seismic resistance of the joints of low-rise steel structures and to propose joint details based on the test results. The influence of different number of bolts on the moment joints was thoroughly investigated. It was found that the flexural capacity of the joints in the direction of weak axis was highly dependent on the number of high-tension bolts. In addition, even though the flexural connections subjected to cyclic loading was perfectly designed in accordance with current design codes, severe failure mode such as block shear failure could occur at beam flange. Therefore, to prevent excessive deformation at bolt holes under cyclic loading conditions, the holes in beam flange need to have larger bearing capacity than the required tensile force. In particular, if the thickness of the connecting plate is larger than that of the beam flange, the bearing capacity of the flange should be checked for structural safety.
평면이방성 암석의 특성을 실험적으로 규명하기 위하여 이방성각도에 따른 일축압축강도 및 변형률, 탄성상수의 변화를 분석하였다. 실험에는 유상구조가 뚜렷한 유문암의 7개의 서로 다른 각도를 갖는 총 35개 시험편을 사용하였다. 본 연구의 제 1보에서는 시험자료의 각도에 따라 개별적인 분석을 주로 논의하였으며, 제 2보에서는 이들 자료를 종합적으로 검토할 것이다. 수평 및 수직시료에서는 가정식을 적용하지 않고 4개의 탄성상수를 얻을 수 있기 때문에 이들의 크기는 참값이라 결정할 수 있다. 변형률 측정에서 각도에 따라 자료의 분산 정도가 달라지는데, 작은 각도에서는 큰 각도보다 분산이 크게 나타났다. 겉보기 탄성계수의 변화는 각도에 따라 M자 또는 U자 형태로 측정되었다. 낮은 각도에서는 겉보기 탄성계수의 변화가 단조증가의 경향을 보이지 않으므로 Saint-Venant 식을 적용될 수 없으며, E1의 크기는 참값범위에 포함되는 값을 얻을 수 없다. 75도 각도의 시료는 변형률과 강도의 측정 편차가 가장 작게 나타났으며, 해석된 4개의 모든 탄성상수가 참값의 범위에 포함되었다. 따라서 만약 한 개의 시험편에서 평면이방성의 탄성상수를 얻고자하는 경우에, 이방성각도가 75도 근처의 시험편을 선정하는 것이 바람직하다.
Various efforts have been made to reduce the weight of concrete slabs while preserving their flexural strength. This will result in reducing deflection and allows the utilization of longer spans. The top zone of the slab requires concrete to create the compression block for flexural strength, and the tension zone needs concrete to join with reinforcing for flexural strength. Also, the top and bottom slab faces must be linked to transmit stresses. Voided slab systems were and are still used to make long-span slab buildings lighter. Eight slab specimens of (1000*1000 (1000*1000 mm2) were cast and tested as two-way simply supported slabs in this research. The tested specimens consist of one solid slab and seven voided slabs with the following variables (type of slab solid and voided), thickness of slab (100 and 125 mm), presence of steel fibers (0% and 1%), and the number of GFRP layers). The voids in slabs were made using high-density polystyrene of dimensions (200*200*50 mm) with a central hole of dimensions (50*50*50 mm) at the ineffective concrete zones to give a reduction in weight by (34% to 38%). The slabs were tested as simply supported slabs under partial uniform loading. The results of specimens subjected to monotonic loading show that the combined strengthening by steel fibers and GFRP sheets of the concrete specimen (V-125-2GF-1%) shows the least deflection, deflection (4.6 mm), good ultimate loading capacity (192 MPa), large stiffness at cracking and at ultimate (57 and 41.74) respectively, more ductility (1.44), and high energy absorption (1344.83 kN.mm); so it's the best specimen that can be used as a voided slab under this type of loading.
원전의 1차 계통 건전성 확보를 위한 일환으로서 초음파 검사 방법은 매우 중요하다. 그러나, 초음파는 검사 대상제의 내부 구조 및 형상에 따라 검사의 제한을 받으므로 결정립이 큰 재질에서 후방 산란 잡음 즉 시 불변성(time invariant) 잡음이 발생한다. 이로 인하여 수신 신호는 낮은 신호 대 잡음비의 결과로 나타나게 된다. 주파수 대역 분할 방식(split spectrum processing:SSP) 기술은 이와 같은 잡음을 억제하는데 효율적이다. 그러나, 종래의 SSP 기술은 minization, PT 알고리즘중 한 알고리즘만 적용하였으나 본 논문에서는 이두 가지 알고리즘을 동시에 처리하는 MPO(minimization and polarity threshold)알고리즘을 적용하고, 주파수 대 대역폭비가 일정한 FIR 여파기로서 새로운 constant-Q SSP를 수행하여 신호처리 시간을 단축하였다. 현장 검사 요건과 동일하게 종파와 횡파에도 일부 적용하였다. 한편, 이러한 새로운 SSP 기술을 적용할 수 있도록 초음파 탐상기를 설계 제작하였고, 시험편들의 준비는 원전 모재 대비시험편, 모재와 동일한 재질의 스테인레스 스틸 및 구리 시험편들이며, 이들 시험편으로 부터 초음파 신호를 수집하여 본 신호 처리를 적용한 결고 신호 대 잡음비가 향상됨을 알 수 있었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.