• Asian Journal of Atmospheric Environment
• /
• v.6 no.4
• /
• pp.281-287
• /
• 2012

Aerosol concentrations at the CC-Lag site in the Teshio Experimental Forest increased from winter to spring and sometimes showed extremely high values associated with Kosa and/or forest-fire events. The range and mean of the mass concentrations of aerosol chemical species were as follows: total particulate mass, 1.2-29, 5.0; elemental carbon, 0.061-2.2, 0.43; organic carbon, 0.059-3.5, 0.79; and sulfate, 0.12-6.2, 1.8 ${\mu}g/m^3$. The total masses of the deposited particles on hybrid larch and on bamboo leaves were approximately 35 and 30 ${\mu}g/cm^2$, respectively. The amounts of soil particles on the leaves were 6 ${\mu}g/cm^2$ for the upper part of hybrid larch, 2 ${\mu}g/cm^2$ for the lower part of hybrid larch, and 1 ${\mu}g/cm^2$ for Sasa bamboo leaves. The amounts of deposited black carbon were 2.3 ${\mu}g/cm^2$ for the upper part of hybrid larch, 0.6 ${\mu}g/cm^2$ for the lower part of hybrid larch, and 0.2 ${\mu}g/cm^2$ for Sasa bamboo leaves. Half of the total deposited particular mass was attached on the hybrid larch; however, most of the total deposited mass was adhered on the Sasa bamboo leaves. Regardless of the species, there tend to be more deposited particles on the leaves in the upper part than in the lower part, with only a few meters height difference. Comparing the composition of the deposited particles to that of the atmospheric aerosols without any size cut, the fractions of water-soluble material sulfate and sea salt in the deposited aerosols were about one tenth and one hundredth lower than that in the aerosols, respectively. On the basis of the measured concentration and the deposited amount on leaves, the deposition velocity of black carbon was estimated to be approximately 0.5 cm/s.

• Journal of Korean Society of Forest Science
• /
• v.88 no.2
• /
• pp.266-272
• /
• 1999

Aboveground biomass and nutrient contents of a 31-year-old pitch pine(Pinus rigida) and a 31-year-old Japanese larch(Larix leptolepis) plantations were measured in the Chungbu Forest Experiment Station, Kyunggi Province. Aboveground biomass was 170.2ton/ha in the pitch pine and 87.2ton/ha in the Japanese larch plantations. Aboveground biomass difference between both plantations was due to the difference of stand density. Aboveground biomass in both plantations was allocated as follows : stemwood>branch>stembark>needle. The concentrations of all nutrients(N, P, K, Ca, Mg) were generally higher in the Japanese larch needle than in the pitch pine because of high nutrient uptake characteristics of larch compared with pine tree species. The nutrient concentration in different tree tissues in both tree species decreased in the order of needle>branch>stembark>stemwood. Nutrient contents of aboveground biomass were : N, 335.9 ; P, 40.4 ; K, 121.4 ; Ca, 188.6 ; Mg, 93.8kg/ha in the pitch pine plantation, while nutrient contents in the Japanese larch plantation were : N, 226 ; P, 11.5 ; K, 72.9 ; Ca, 75.7 ; Mg, 37.1kg/ha. The nitrogen use efficiency calculated as the biomass produced by one unit of nitrogen was higher in the pitch pine than in the Japanese larch plantations. This result suggests that pine with high nitrogen use efficiency could be adapted in lower site productivity area compared with larch tree species.

• Journal of the Korea Furniture Society
• /
• v.26 no.2
• /
• pp.138-144
• /
• 2015

Among several thermal wood modification methods German oil heating technology was applied for color changing larch and paulowniawood specimens. They were heat treated at $200^{\circ}C$ for 3 hours in an autoclave filled with linseed oil. The CIE $L^*a^*b^*$ color indexes of the shells and cores of the oil heated specimens were measured. The color difference indexes between the oil heated and the control specimens of larch and paulowniawood were in the range of 6 and 12, which implies considerably different. The color difference indexes between the core layers of the larch and paulowniawood specimens were 4.3 and 1.7, respectively. It could be concluded that the specimens of the two species were color changed uniformly by oil heating.

• Journal of the Korea Furniture Society
• /
• v.22 no.4
• /
• pp.265-269
• /
• 2011

To make value-added products from small-diameter larch logs it is necessary to reduce the color variation between boards. The effect of heat treatment on the color variation was investigated. Four hundred air-dried larch squares were visually classified into six groups. The largest color difference index between them was 8.8. When they were kiln-dried lower than $120^{\circ}C$, their average color difference indexes decreased to less than 6.0 compared with the air-dried. However statistical analyses revealed that kiln-drying largely increased the variation of the indexes of the color elements. Heat-treatment above $150^{\circ}C$ increased the color difference indexes with the increase of temperature. The variation of color difference indexes within a group at $190^{\circ}C$ were less than the groups at $150^{\circ}C$ and $170^{\circ}C$. It implies that heat treatment at $190^{\circ}C$ could make the color of larch squares uniform.

• Journal of the Korea Furniture Society
• /
• v.21 no.4
• /
• pp.273-283
• /
• 2010

Structural larger timber have some weak points as like much longer drying time at lower MC(15%), a considerable check developing and the difficulty for the chemicals injection, so it is necessary to develop lighter structural size member for using the new Hanok, heavy timber construction, living necessaries, furniture and industrial goods. The developed skin timber can be a good raw material for those uses. Skin timber is a hollowed timber which be bored out of its considerable cross-sectional area. The intention of this study was the evaluation of compressive capacity of skin timber. Specially, skin timbers which have more than 200mm in sizes were used to analyze the compressive capacity. From the results of this study, the following conclusions have been made: 1. Though considerable inner parts were bored out, both pine skin timber and larch skin timber showed a good compressive capacity to that of non-bored solid timber. 2. According to ASTM, pine skin timber showed various failure types, but Splitting type, Brooming and end rolling type were main failure types for the larch skin timber. 3. Pine skin timber didn't show the significance between cylindrical shape and rectangular shape, but larch skin timber showed the significance between two shapes. Therefore, for the larch skin timber, cylindrical shape and rectangular shape should be used as a column uses and beam uses respectively. 4. Pine skin timber and larch skin timber didn't show the significance on the compressive capacity. There is not much difference of compressive capacity between them, so it can be possible to select on the user convenience.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.1
• /
• pp.1-9
• /
• 2012

Densified fuels from biomass are widely used in North America and Europe as a regenerable and clean bioenergy. In this study, the fuel characteristics and densification characteristics of Japanese larch and Hyunsasi poplar were studied using a piston-type briquetting machine. The effects of pressure, pressure holding time, species, and particle size on briquette characteristics were studied. At room temperature, the highly densified briquettes of Japanese larch and Hyunsasi poplar can be produced at a compression pressure of 110~170 MPa. The produced briquettes have densities between 0.66 and 0.94 g/$cm^3$ after 28 days of storage at room temperature. The optimum pressure holding time was found to be 12 seconds. There is a linear increase in pressure with increase in density. The densities of briquettes from Japanese larch were higher than those of briquettes from Hyunsasi poplar. Also, the coarser particle size resulted in higher densities in briquettes than the finer particle size.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.1
• /
• pp.57-66
• /
• 2021

In recent years, the use of cross laminated timber (CLT) has been evolving. In addition, CLT manufactured with various species such as Japanese cedar has been developed to utilize the local resources in each country. However most factories in Japan produce CLT by bonding the laminae in width direction for orthogonal layers, where grain of element is perpendicular to the grain of outer layer, and this process is considered to be one of the factors that reduce productivity. A new wood based material (hereinafter referred to as Ply-lam) using wooden panel such as plywood for the orthogonal layer was developed in order to improve productivity in CLT manufacturing and improve quality. Japanese cypress lamina was used for the parallel layer, where grain of element is parallel to the grain of outer layer, of CLT and Korean larch plywood was used for the orthogonal layer, in order to effectively use Korean larch and expand the utilization of Japanese cypress. The cross-sectional construction of the Ply-lam was 5-layers 5-plies, and the dimensions were 1000 mm (width) × 150 mm (depth) × 4000 mm (length). As a performance evaluation of the manufactured Ply-lam, strength tests such as out-of-plane bending, in-plane bending, out-of-plane shearing and in-plane shearing tests were carried out. As the result of this study, Ply-lam composed of Japanese cypress lamina panels and Korean larch plywood showed very higher out-of-plane bending strength compared to the standard strength of CLT. And the result obtained in other tests seems to show a sufficiently high value.

• Korean Journal of Agricultural Science
• /
• v.48 no.4
• /
• pp.753-760
• /
• 2021

This study was carried out to discover suitable packaging methods during the cold or frozen storage of sawtooth oak and Japanese larch seedlings, which are major afforestation tree species in Korea. The weight loss rate of sawtooth oak was lower under frozen storage at -2℃ (maximum, 33.7%) than under cold storage at 2℃ (maximum, 61.0%). A film liner treatment inside the packaging box effectively suppressed the increase in the weight loss rate. For the sawtooth oak containerized seedlings, when stored at -2℃, the rate of weight loss was 17.9 to 25.4% in the untreated group and less than 1% in the film liner treatment group. Similar results were observed with Japanese larch. After two months of freezing at -2℃, both species maintained a low index of 1.0 - 1.1 with regard to the degree of shoot desiccation of containerized seedlings, and there was no significant difference between the treatments. On the other hand, the chlorine dioxide treatment could more effectively reduce the occurrence of mold and shoot desiccation than a PE single treatment in bare-root seedlings. According to these results, it was concluded that frozen storage is generally suitable as a means of long-term storage compared to cold storage of sawtooth oak and Japanese larch. A chlorine dioxide treatment at 20 ppm was effective for maintaining seedling quality levels during storage, demonstrating the good effect of suppressing the occurrence of shoot desiccation and the occurrence of mold.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.25-31
• /
• 1974

1. Various gluing qualities applying Resorcinol Plyophen #6000 were studied on aiming the strength relationships of laminated woods resulted by single species [poplar (Populus deltoides), larch(Larix leptolepis)], mixed species of (poplar and larch), preservatives, treated poplar the scarf joint with mixed species of poplar and larch and the scarf joint treated with preservatives. 1. 1 On the block shear and on the DVL tension test, the mean wood failure ratio showed an excellent value i.e., above 65% and the tangential strength for larch was higher than that of radial, but it was reversed for poplar as shown in Tables 1 and 2. 1. 2 The lamina treated with Na-PCP reduced slightly the strength but the limited strength allowed for manufacturing laminated wood was not influenced by treating Na-PCP as shown in Tables 3 and 4. 1. 3 The safe scarf ratio in the plane scarf joint was above 1/12 for larch and 1/6 for poplar regard less of the chemical treatment or untreatment as shown in Tables. 5, 6, 7 and 8. 2. In the normal and boiled state, the gluing quality of the laminated wood composed of single[poplar (Populus deltoides), larch (Larix leptolepis)] and double species (poplar and larch) glued with Resorcinol Plyophen #6000 were measured as follow, and also represented the delamination of the same laminated wood. 2.1 The normal block shear strength of the straight and curved laminated wood (in life size) were more than three times of the standards adhesion strength. And, the value of the boiled stock was decreased to one half of the standard shear adhesion strength, but it was more than twice the standard strength for the boiled stock. Thus, it was recognized that the water resistance of the Resorcinol Plyophen #6000 was very high as shown in Tables 9 and 10. 2. 2 The delamination ratio of the straight and curved laminated woods in respect of their composition were decraesed, in turn, in the following order i. e., larch, mixed stock (larch+poplar) and poplar. The maximum value represented by the larch was 3.5% but it was below the limited value as shown in Table 11. 3. The various strengthes i.e., compressive, bending and adhesion obtainted by the straight laminaced wood which were constructed by five plies of single and double species of lamina i. e., larch (Larix leptolepis) and poplar (Populus euramericana), glued with urea resin were shown as follows: 3. 1 If desired a higher strength of architectural laminated wood composed of poplar (P) and larch (L), the combination of the laminas should be arranged as follows, L+P+L+P+L as shown in Table 12. 3.2 The strength of laminated wood composed of laminas which included pith and knots was conside rably decreased than that of clear lamina as shown Table 13. 3.3 The shear strength of the FPL block of the straight laminated wood constructed by the same species which were glued with urea adhesives was more than twice the limited adhesion strength, thus it makes possible to use it for interior constructional stock.

• Journal of the Korea Furniture Society
• /
• v.23 no.2
• /
• pp.214-221
• /
• 2012

Sustainable energy consumption and increasing $CO_2$ emissions stimulate Eco-friendly industry. Wood has positive various properties as alternative energy such as solar, wind and water. Wood provide lumber, pallet, paper, pulp and fuel through production process. Even Korea republic has 63.7% of forest rates, weather condition makes low forestry production capacity. For utilization of domestic small diameter log needs study mechanical properties. In this study, various properties tested on domestic Japanese Larch small diameter lumbers and make mechanical properties table for allowable stress calculation. Result of compressive test, allowable compressive stress is 13 MPa. Allowable bending stress is 12 MPa.