• Journal of the Korean Wood Science and Technology
• /
• v.38 no.2
• /
• pp.94-100
• /
• 2010

This study was performed to develop an LRFD (Load Resistance Factored Design) Code for Domestic Larch. To accomplish his, we evaluated bending, compression, tension and shear strength. The results of the strength evaluation were utilized to verify the distribution and code conversion. For bending, tension and compressive strength, the Weibull distribution was well-fitted, but for shear strength we observed a normal distribution. For evaluating the bending and compressive strength, a full-sized specimen was used. A small clear specimen was used to test tension and shear strength. Compressive strength in particular was found to be affected by tight knots, although there was little difference between grades. In the code conversion, the design value of the LRFD was larger than the existing allowable stress value in the Korean Building Code. However, the allowable stress in this study was about two times higher than the value listed in the Korean Building Code. This result induced the difference between the soft and hard conversions. For greater reliability, the accumulation of additional data is necessary and further studies should be performed

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.2
• /
• pp.125-131
• /
• 2011

The characteristics of radio-frequency/vacuum drying Japanese larch boxed heart round logs with 150 mm and 210 mm in diameter and 2,500 mm in length, subjected to compressive loading, after the pretreatment of kerf were investigated. The results of this study were as the follows: The drying time of about 120 hours~130 hours was needed from green to about 15 percent of moisture content. The gradient of final moisture content for all specimens was very gentle in both longitudinal and transverse directions owing to dielectric heating. The surface checks seriously occurred although the occurrence extent of surface check for the kerfed specimens was slight compared with that for the control specimens because drying stress was relieved by kerf. The occurrence of surface checks for the L-specimen was more serious than that for the S-specimen.

• Journal of Forest and Environmental Science
• /
• v.33 no.2
• /
• pp.147-153
• /
• 2017

The purpose of this study was to examine productivity and cost of tree-length harvesting using cable yarding system in a larch (Larix leptolepis) clear-cutting stand located in Pyeongchang-gun, Gangwon-do. We used tree-length harvesting method using cable yarding system with a tower yarder HAM300. The productivity was $17.6m^3/hr$ for felling, $12.4m^3/hr$ for delimbing, $4.2m^3/hr$ for yarding, and $8.1m^3/hr$ for processing. The total cost of the harvesting system was $48,381won/m^3$, which was majorly composed of yarding operation cost, at $40,169won/m^3$ (79.3%), while felling had the lowest cost at $1,154won/m^3$ (4.1%). Major factors affecting felling and processing productivity was tree volume and the number and thickness of branches for delimbing productivity. In addition, we suggest that training and education for machine operators were critical to improve yarding productivity.

• Journal of Korea Foresty Energy
• /
• v.20 no.2
• /
• pp.41-45
• /
• 2001

Japanese Larch(Larix kaempferi) was treated with aqueous solutions(30%, 40%, 50%) of polyethylene glycols(PEG, #1000, #1500, #4000, #6000) for the dimensional stabilization. The antiswelling efficiency(ASE) was measured for the evaluation of the dimensional stabilization. The weight percent gains(WPGs) of the woods treated with 40% solutions were higher than those of the others, and the highest WPG was achieved by treatment with 40% solution of PEG #1500. The ASE decreased with increasing molecular weight of PEG. ASE of woods treated with PEG #1000 and PEG #1500 were higher than those of the others.

• Journal of Plant Biotechnology
• /
• v.36 no.3
• /
• pp.230-235
• /
• 2009

The effect of auxin transport inhibitor (TIBA and PCIB) or auxin synergist (phloroglucinol) on somatic embryo maturation and germination in Japanese larch (Larix leptolepis) was examined. The addition of 15.8 mg/L ABA+5.0 mg/L PCIB showed most promoted the maturation of cotyledon -staged somatic embryos (177.7/90 mg ESM). In contrast, with treatment of 5.0 mg/L PCIB or 5.0 mg/L TIBA, no somatic embryos were obtained. Considering from this result, PCIB or TIBA alone could not substitute for exogenously supplied ABA for maturation of somatic embryos. In the test of below concentration of 5.0 mg/L PCIB, the highest results were recorded in 15.8 mg/L ABA+2.0 mg/L PCIB (109.3/90 mg ESM) or 15.8 mg/L ABA+5.0 mg/L PCIB (103.7/90 mg ESM). However, 5.0 mg/L phloroglucinol (0/90 mg ESM) or no ABA addition (3/90 mg ESM) had little influence on somatic embryos maturation. In germination study, the highest frequency of plantlet regeneration obtained from the somatic embryos which had matured on 15.8 mg/L ABA+5.0 mg/L PCIB (67.9%). However, either 5.0 mg/L PCIB nor 5.0 mg/L TIBA resulted in obtained from plantlets.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.2
• /
• pp.6-15
• /
• 1998

A total of forty five-ply, 30- by 30-cm lauan and larch plywood sheets were manufactured in the laboratory using commercial urea and phenol resin adhesives; half of these sheets were treated with fresh concrete. Each sheet was carbonized for 2, 4, and 6hours at $400^{\circ}C$, $600^{\circ}C$, and $750^{\circ}C$, respectively, and their physical properties were measured. The yie1d of charcoal decreased as carbonization temperature and time increased. Charcoal yield was greater in plywood than in veneer, and slightly greater in plywood treated with concrete compared to untreated plywood. Plywood manufactured with phenol resin adhesive had higher pH, higher equilibrium moisture content (EMC), and greater adsorption of methylene-blue dye compared to plywood manufactured with urea resin. For concrete-treated plywood, pH was greater than 10 even when the sheets were carbonized for 2hours at $400^{\circ}C$. Although the EMC of the phenol resin plywood was higher than that of the urea resin plywood, EMC of the phenol resin was lower than that of the urea resin. The larch phenol resin plywood that was carbonized for 6 hours at $750^{\circ}C$ adsorbed more methylene-blue than did the commercia1 wood-based activated charcoal as a result of total pore volume and surface area.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.3
• /
• pp.16-22
• /
• 1995

The profiles of the heating temperature in three water vat temperatures (55, 66 and 77$^{\circ}C$) and the cooling temperature under the average ambient temperature of 3$^{\circ}C$ in 4 and 10cm depths from surface at the center of veneer bolts length showed similar patterns for Japanese larch (Larix leptolepis). Dahurian larch (Larix gmelinei) and Radiata pine (Pinus radiata). The difference of these core temperatures of 10cm depth from surface varied proportionally with the increase of vat temperatures. The average heating time based on final core temperature of 6$^{\circ}C$ lower than vat temperature required about 14.5 hours in vat temperature of 55$^{\circ}C$ and 13.5 hours in vat temperature of 66and 77$^{\circ}C$. Each internal temperature of 4 and 10cm depths from surface started to decrease from the beginning of cooling and after about two hours.

• The Korean Journal of Ecology
• /
• v.25 no.6
• /
• pp.399-403
• /
• 2002

Cellulose mass loss by cellulose filter papers was measured for 3 time (35 days, 70 days, 105 days) incubation during the growing season (from May to September 2002) with different tree density and after fertilization in a Japanese larch (Larix leptolepis) plantation. Cellulose mass loss rates were significantly different between tree density types and fertilization treatments during the study periods. After 105 day incubation of cellulose filter paper, cellulose mass loss rates were significantly higher in the low tree density (70.1 $\%$) than in the high tree density (49.9$\%$). Cellulose mass loss rates averaged 62.8$\%$ in the fertilization and 58.9% in the unfertilization treatments during the same periods. However, cellulose mass loss was not significantly different between the forest floor and the mineral soil layer except for 35 day incubation. The results indicate that cellulose decomposition rates are a useful index to express differences in organic matter decomposition activity in different tree density and after fertilizer treatments.

• Journal of Korean Society of Forest Science
• /
• v.10 no.1
• /
• pp.1-3
• /
• 1970

It is quite difficult to analyse the profit that can be obtained from tree plantations because very many factors are involved. However, for giving sound guidelines to forestry enterprices, it is beneficial in calculating the cost ratios. The present author has made some predetermined assumptions for this calculation relating to larch plantations. According to the results, to insure a sound enterprice, the rate of the annual compound interest should be less than 8 percent taking into consideration the risk ratio. It is true, however, that we do not always depend only upon profit analysis results in forest management.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.1
• /
• pp.28-36
• /
• 1997

Several thick board and dimension lumbers of Japanese larch(Larix leptolepis), Dahurian larch(Larix gmelini) and radiata pine(Pinus radiata) air-dried in four different seasons to compare air-drying process. Patterns of air-drying curves were influenced by climatological conditions and limber thickness. The initial drying rates of summer were the highest, followed those of fall, spring and winter. The drying times to equilibrium moisture contents for four seasons were nearly the same except for winter. However, the drying time for winter required twice more time than the other seasons. The drying time of dimension lumbers required 1.3 times more than boards. The final moisture contents were lowest during spring, highest during winter and similar between summer and fall.