• 한국가스학회지
• /
• 제25권2호
• /
• pp.22-27
• /
• 2021

이 논문은 LPG 자동차용 엔진의 고장사례를 연구하여 자동차 생산에 활용함이 목적이다. 첫번째 사례는 엔진의 실린더헤드를 분해하여 확인한 결과 실린더 헤드의 점화플러그가 조립되는 나사부 마멸때문에 점화플러그의 불꽃이 누설되어 출력이 떨어지면서 엔진의 부조화 현상이 가끔 유발되는 것을 발견하였다.. 두 번째 사례는 캠샤프트의 위치와 크랭크 샤프트 위치를 맞춘 타이밍 마크가 0.5칸 틀어져 엔진의 부조화 현상이 발생된 것을 확인되었다. 세 번째 사례는 실린더 헤드를 분해하여 확인한 결과, 실린더 헤드에 제거되지 못한 이물질이 3번 흡기포트에서 공기 흐름에 따라 이동하다가 흡기밸브의 닫힘시기를 원활하지 못하여 하여 고장이 발생된 것을 확인하였다. 따라서, 자동차 관리자는 철저하게 점검해야 하고, 자동차 생산자는 철저한 품질확보를 통해 고장의 원인을 제거해야 할 것으로 판단된다.

• 한국산학기술학회논문지
• /
• 제19권5호
• /
• pp.681-688
• /
• 2018

최근 강화된 환경규제 및 높은 연비에 대한 요구로 인해 천연가스를 연료로 사용하는 선박이 증가하고 있다. 친환경 선박 연료로 대두되고 있는 LPG 혹은 메탄올을 사용한 선박의 요구도 증가하고 있다. 이러한 흐름의 연장선상으로 LPG 혹은 메탄올을 사용하는 ME-LGI 엔진에 대한 연구가 최근 활발히 이루어지고 있다. ME-LGI 엔진을 탑재한 선박은, 선박 항해 중 연료분사밸브의 작동 신뢰도를 지속적인 테스트를 통해 확인해야할 필요가 있다. 따라서 연료분사밸브 테스터의 개발은 ME-LGI 엔진의 상용화를 위해 반드시 필요하다. 이에 본 연구에서는 요구조건 분석, 기능분석, 설계 합성의 순서로 진행되는 시스템 엔지니어링 프로세스를 활용하여 ME-LGI 엔진용 연료분사밸브 테스터의 개념설계를 수행하였다. 요구조건 분석 단계에서 먼저 연료분사밸브의 작동 프로세스를 분석하였고, 밀폐 오일 누유 여부 확인의 필요성을 도출하였다. 그 다음 기능분석 단계에서 연료분사밸브 테스터의 기능 및 기능의 흐름을 수준별로 정의하였다. 이후 설계 합성 단계에서 각 기능에 해당하는 장비들을 설정하였고, 이를 바탕으로 process block diagram을 도출하였다. 또한 시스템 분석 및 조정 단계의 일환으로 초기위험도 분석을 수행하여 안전 방안을 개념설계 안에 추가하였다. 본 연구는 시스템 엔지니어링 프로세스가 개념설계에 적용되는 과정을 상세히 보여줌으로써 향후 타 시스템의 개념 설계 시 좋은 참고자료가 될 수 있을 것으로 기대된다.

• 한국수소및신에너지학회논문집
• /
• 제15권2호
• /
• pp.129-136
• /
• 2004

환경문제와 석유자원의 고갈이 많은 연구자들을 기존 탄화수소연료를 대체할수 있는 재생 가능한 연료를 구하는데 많은 노력을 기울이고 있다. 수소연료는 유해배기물질이 없는 연소와 또한 연소후에 재생 가능한 물성분만 배출하는 속성으로 미래의 청정에너지로 각광을 받고 있다. 이러한 이유로 수소연료는 수송기계의 연료로도 주목을 받고 있다. 따라서 수소연료기관 개발은 21세기에도 지속적으로 진행될 것이다. 이에대한 초기연구로 기체 LPG 연료가 아닌 액체 LPG 연료를 흡기관에 분사하여 기화된 LPG 연료를 엔진으로 흡입하는 LPi엔진에 수소연료를 과급하여 엔진에 성능을 연구하고자 하였다.

• 한국분무공학회지
• /
• 제19권1호
• /
• pp.40-46
• /
• 2014

Recently rise in oil prices feet the burden on not only diesel vehicle driver but also LPG vehicle driver, and get interested in various way to reduce fuel costs. In this study discuss on exhaust emissions characteristics on driving cycle mode and ignition advance condition change of CNG/LPLI Bi-Fuel vehicle. Experimental test was performed by changing the conditions of fuel (LPG/CNG), spark advance (Base, $10^{\circ}CA$, $15^{\circ}CA$), and driving mode (FTP-75, HWFET, and NEDC). In case of CO emission, in the order of CNG Base, CNG S/A10, S/A15 condition are average reduced -21%, -35%, -29% respectively compared to LPG fuel. The active emission reduction from the initial engine start, spark retard is likely to be beneficial in catalyst warm-up and improve combustion stability rather than spark advance.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.99-105
• /
• 2003

The configuration of intake port is a dominant factor of inlet air flow and mixture formation in an engine. In this study, as an available technology to optimum intake port, the flow box system using resine has been applied. So we presents a methodology for estimating inlet flow characteristics in this paper. This quantified experimental result shows good agreements with visualization data in a cylinder. We obtained the optimal value of swirl ratio and flow coefficient under steady flow rig test for new development of intake port for heavy-duty engine. From this results, the cylinder heat with a good evaluated swirl flow characteristics was developed and adapted for a 11L heavy-duty engine using the liquid phase LPG injection (LPLi) system. This .research expects to clarify major factor that make the intake port efficiently.

• 한국분말재료학회지
• /
• 제6권2호
• /
• pp.163-170
• /
• 1999

Engine valve seat is a functionally important part for maintaining engine performance. The progress of automotive technology has increased the severity of conditions to which it is exposed, especially as regards LPG fuel engines and turbocharger. Therefore, it requires excellent heat and wear resistance to meet the severe condition inside the engine. In the present study, effects of solid lubricants such as CaF$_2$, MnS and MoS$_2$ on microstructure and mechanical properties of sintered Fe alloys for valve srats have been investigated for the development of valve seat material with high temerature wear resistance. As a results of engine simulation test, 0.5 wt% CaF$_2$ specimen showed the most excellent property, but in the overall aspect of view valve recession has increased with increasing the amount of solid lubricants.

• 한국수소및신에너지학회논문집
• /
• 제10권4호
• /
• pp.233-243
• /
• 1999

Combustion characteristics of synthetic gas from flame pyrolysis gasification of polymetric wastes are reported and the applicability of synthetic gas from flame pyrolysis gasification to a gas engine system is presented. Engine power is easily predicted by the volume percentage of the synthetic gas. Measurements have been made to obtain the range of flame existence in the function of volume percentage of CO and $H_2$ gases in the synthetic gas. In order to clarify the emission of the flames, NOx measurements by chemiluminescent analyser are taken in flames with different equivalent ratios. From the results of the engine performance data we also have demonstrated that the output of the gas engine modified from a LPG engine is about 5 ps at normal rating. We conclude that synthetic gas from flame pyrolysis gasification of polymetric wastes is applicable to a gas engine system.

• 한국분무공학회지
• /
• 제14권1호
• /
• pp.34-38
• /
• 2009

This paper presents the pulsation of carburetor inlet and outlet pressure of a small SI gasoline engine. The engine used in this paper is a 23cc, single cylinder, diaphragm carburetor, two-stroke, air-cooled for brush cutter. The rpm and pressure wave pulsation at the inlet and the outlet of carburetor were measured and analysed for the understand of the internal air flow into the barrel on the diaphragm carburetor. These data should be used for the development of the duel fuel injection system for gasoline and LPG. The results showed that the carburetor inlet pressure variations were very steady, but the pressure variations at carburetor outlet were very sensitive to the pressure variation into the crank case and were to similar independently to the engine speed on partial opened throttle conditions. According to increasing engine speed, the pressure waves started to come out and be developed after closing the intake port of the engine at carburetor outlet. Reverse flow occurred on the WOT (wide open throttle) condition.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2005년도 학술발표논문집
• /
• pp.592-597
• /
• 2005

Biogas is widely accepted as one of renewable energy. Raw biogas can be used in internal combustion engines either spark ignition or diesel engines. Since the gas has relatively low calorific values, engine power also is lower than rated power values. Modified engines or biogas-specific engines have been utilized in order to increase efficiency. Recently, gas engine/generators are provided for various purposes. They are mostly for LPG or natural gas. When biogas is fueled to the gas engines, de-rating is inevitable due to its lower calorific values. Meanwhile, massively produced commercial gas engines are more competitive in terms of initial investment for engines, compared to biogas-specific engines. Then, the characteristics of the commercial engine and power generation should be understood for better operation. A 5kW gas engine/generator(natural gas) was tested for determining an allowable maximum concentration of $CO_2$ in synthetic biogas, with respect to engine stating, power generation. Experimental results indicated that about 65% of methane concentration is required to start the gas engine. At this condition, the power generated was about 3 kW. It is about 60% of the nominal power, which is similar to the ratio of calorific values.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.1-11
• /
• 2014

The aim of this study is to investigate the effect of SCR reactor on the exhaust emissions characteristics in order to develop a urea-SCR aftertreatment system for reducing $NO_x$ emissions. The experiments are conducted by using a flue tube LPG steam boiler with the urea-SCR aftertreatment system. The urea-SCR aftertreatment system utilizes the ammonia converted from 17% aqueous urea solution injected in front of SCR catalyst as a reducing agent for reducing $NO_x$ emissions. The equivalence ratio, urea injection amount, ammonia slip and $NO_x$ conversion efficiency relative to boiler load are applied to discuss the experimental results. In this experiment, the average equivalence ratio is calculated by changing only the fuel consumption rate while the intake air amount is constantly fixed at $25,957.11cm^3/sec$. The average equivalence ratios are 1.38, 1.11, 0.81 and 0.57 when boiler loads are 100, 80, 60 and 40%. The $NO_x$ conversion efficiency is raised with increasing urea injection amount, and $NH_3$ slip is also boosted at the same time. Consequently, the $NO_x$ conversion efficiency relative to boiler load should be examined in combination with urea injection amount and $NH_3$ slip. The results are calculated by 89, 85, 77 and 79% for the boiler loads of 100, 80, 60 and 40%. The appropriate amount of urea injection for the respective boiler load can be not discussed by only $NO_x$ emissions, and should be determined by considering the $NO_x$ conversion efficiency, $NH_3$ slip and reactive activation temperature simultaneously. In this study, the urea amounts of 230, 235, 233 and 231 mg/min are injected at the boiler loads of 100, 80, 60 and 40%, and the final $NH_3$ slips are measured by 8.48, 5.58, 11.97 and 11.34 ppm at the same conditions. THC emission is affected by the SCR reactor under other experimental conditions except 100% engine load, and CO emission at only 40% engine load. The rest of exhaust emissions are not affected by the SCR reactor under all experimental conditions.