• Design & Manufacturing
• /
• v.2 no.4
• /
• pp.1-4
• /
• 2008

Micro pattern is applied to the light guiding plate(LGP) to enhance the uniformity of the brightness of the LCD. The micro cones are molded in intaglio on the surface of the LGP. The surface roughness of each cone was 40nm and 38nm in negative and positive die for laser ablation. In chemical etching, the surface roughness was 25nm, 24nm in negative and positive. And the surface roughness of negative and positive dies were 4nm and 5nm for LIGA-reflow process.

• Journal of Information Display
• /
• v.5 no.1
• /
• pp.7-15
• /
• 2004

A highly simplified backlight unit mainly composed of diffractive grating in sub-micron order imprinted light-guide plate (LGP) is proposed for edge-lit backlight unit. Optical characteristics of the imprinted LGP are examined by RCWA and the performance is verified through Monte Carlo simulation. Results show that the diffraction efficiency, luminous flux and its uniformity over the area are significantly affected by the angle of incident ray. Consequently couples of design considerations are additionally proposed to enhance luminous flux. In terms of peak luminance and out-coupling luminous flux, the experimental results are agreed well with the performance simulation. Finally, compared with optical characteristics of conventional backlight unit, we could conclude that the proposed simplified backlight unit made of diffractive grating imprinted light-guide plate is a good substitute for the conventional backlight unit.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.361-367
• /
• 2011

In this paper, it was attempted to analyze the optimal design of light emitting diode (LED), a source of back light unit (BLU). LED is beginning with commercialized red LED which is made by GaAsP compound semiconductor, and has been developed focusing on liquid crystal panel. In order to get the optimal design, optical simulation was made by analyzing luminosity shape, reflector angle, chip depth, and chip position of LED lighting. Final results show that the proposed LED characteristics were useful to increase light efficiency and it has been proven by distribution chart for actual exposed light on the light guide panel (LGP).

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.53.3-53
• /
• 2001

This paper deals with the development of a shape inspection system of the Light Guide Panel(LGP), and the study for the performance of the system. The conventional contact sensing methods have been used to inspect the shape. However the contact-sensing methods have some problems. The contact between a tip of the sensor and the surface of objects make a sensor tip abraded and generate a defect on the surface of objects. In this paper, we employed the Non-Contact Optical Sensor[1] to measure the shape inspection system of LGPs, The Sensor composed of Hologram laser[3] unit used for CD Optical Pickup[2] is low cost and has a good performance to measure a transparent objects. From the results of experiments for LGP shape inspection ...

• LP가스
• /
• s.85
• /
• pp.65-73
• /
• 2003

최근 산업자원부는 올해 국내 LGP수요는 전년대비 3.9%가 증가한 8백47만톤이며, 이중 프로판은 지난해와 비슷하고 부탄은 6.7%가 늘어날 것으로 내다봤다.

• Transactions of Materials Processing
• /
• v.20 no.1
• /
• pp.11-16
• /
• 2011

Recently, according to the rapid development of display, many display applications, such as, cellular phone, navigation, monitor and LCD TV have been changed from CRT type to LCD type. BLU(Back Light Unit) is one of main parts in LCD unit and generally, it consists of a light source, a reflective sheet, a LGP(Light Guide Plate), a diffuser sheet, and two prism sheets. The most important component of BLU is a light guide plate, which diffuses the input light to the TFT-LCD module uniformly. The LGP is usually made by injection molding process, and it has numerous optical micro patterns on the surface. In the present study the micro-patterned stamper which has cylindrical shape was fabricated by using the UV-LiGA process. And the replication characteristics have been compared among three different kinds of injection molding process; general injection molding, injection/compression molding and RHCM(Rapid Heating and Cooling Molding). Average replication ratios of CIM and ICM were 19.1% and 64.6%, respectively. On the other hand, the average replication ratio of RHCM process showed the higher value of 98.4% among these. It show that maintaining the mold surface above $T_g$ could increase the replication ratio of micro patterns substantially.

• Design & Manufacturing
• /
• v.2 no.2
• /
• pp.29-32
• /
• 2008

A back light unit (BLU) is a key module of a thin film transistor liquid crystal display (TFT-LCD), frequently utilized in various mobile displays. In this study, we experimentally characterize transcription and optical properties of concave and convex microlens arrays (MLAs) of light guide plate (LGP) fabricated by injection molding with polycarbonate as a LGP substrate material. Nickel mold inserts were manufactured by electroforming on the MLA which was fabricated by the thermal reflow of photoresist microstructures patterned by UV-photolithography. For the case of convex microlens, the height of replicated microlens was less than that of the mold insert while maintaining almost the same microlens diameter of the mold insert as the location of the microlens is far from the gate. In contrast, for the concave microlens, the diameter of replicated microlens was larger than that of mold insert, while showing almost the same microlens height as the mold insert. From the optical examination of replicated convex and concave MLAs, it was found that a higher luminance of the LGP was achieved by the concave MLAs compared to the convex MLAs (about 30% enhancement in this case)due to the utilization of a larger amount of light provided by the light sources.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.429-429
• /
• 2007

In this study, it was investigated about the variation of luminance properties in LED backlight with geometrical shape such as prism or lens shape on the light-entering face. Generally, LED light source has the loss in backlight system because it has horizontal direction light. PMMA(Poly-Methyl-Meta-Acrylate) is used LGP(Light-Guide-Plate) in conventional backlight system. PMMA has low refraction angle. so that. horizontal direction light was not used in backlight system. The addition of geometrical shape in light-entering face in LGP improves the luminance characteristics because it prevents horizontal direction light generation in light-entering-face. Prism or lens shape in same pitch disposition was almost same without these treatment such as the value of 1% rising. Besides. It is particular that the gap of these shape such as the value of 0.407~0.22mm prevents horizontal direction light, so then it contributes luminance rising at 5.6%.

• Korean Journal of Food Science and Technology
• /
• v.48 no.4
• /
• pp.347-353
• /
• 2016

This study was performed to examine the quality characteristics of the sponge cakes with different contents (2-10% (w/w)) of lemon grass powder (LGP). An increase in LGP content in the cake led to a significant increase in the specific gravity of batter, baking loss rate, redness, hardness, cohesiveness, chewiness, and 1,1-diphenyl-2-picrylhydrazyl radical scavenging activity of the cakes and a significant decrease in pH, moisture content, specific volume, height, volume and symmetry index, lightness, and yellowness of the cakes. Springness and resilience did not show any difference between the cakes. The consumer acceptance test indicated that the addition of LGP up to 2% did not cause a significant negative effect on the consumer acceptances in all attributes. The sponge cakes with 2% LGP can be recommended for manufacturing bakery.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.291-292
• /
• 2008